scholarly journals Semi-interpenetrating networks based on POLY(N-isopropyl acrilamide) and POLY(N-vinylpyrrolidone)

2007 ◽  
Vol 61 (6) ◽  
pp. 350-356 ◽  
Author(s):  
Dragana Zugic ◽  
Pavle Spasojevic ◽  
Jasna Djonlagic
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polymer Networks ◽  
Interpenetrating Polymer Networks ◽  
Molar Ratio ◽  
Dynamic Shear Modulus ◽  
Interpenetrating Networks ◽  
Elongation At Break ◽  
Equilibrium Degree ◽  
Degree Of Swelling

Three series of semi-interpenetrating polymer networks based on cross-linked poly(N-isopropylacrylamide), PNIPA, and 1, 2 and 3 wt% of linear poly(N-vinylpyrrolidone), PVP, were synthesized in order to improve the mechanical properties of PNIPA gels. The effect of the incorporation of the linear PVP polymer into the temperature responsive networks on the phase transition temperature, swelling behavior and mechanical properties was studied. Polymer networks with four different crosslinking densities were prepared with various molar ratios (25/1 to 100/1) of the monomer (N-isopropylacrylamide) to the cross linker (N,N'-methylene-bisacrylamide). The hydrogels were characterized by determination of the equilibrium degree of swelling at 25 ?C, the dynamic shear modulus and the effective crosslinking density, as well as the ultimate hydrogel properties, such as the tensile strength and elongation at break. Furthermore, the deswelling kinetics of the hydrogels was also studied by measuring their water retention capacity. The inclusion of the linear hydrophilic PVP in the PNIPA networks increased the equilibrium degree of swelling, the highest values of which were obtained for samples with 2 and 3 wt% of PVP and the NIPA/MBA molar ratio of 75/1 and 100/1. The highest reinforcement effect, evaluated from the ratio of G'red(semi-IPN) to G'red(PNIPA), was obtained by incorporation of 2 wt% PVP. The tensile strength of the semi-IPNs reinforced with linear PVP was higher than that of the PNIPA networks. The elongation at break of these semi-IPNs varied between 22 and 55%, which are 22^11% larger than those for single PNIPA networks. The tensile measurements confirmed that the presence of 2 wt% of the linear polymer significantly reinforced the PNIPA network.

Semi-Interpenetrating Networks of Sulfur-Containing Bismaleimides

1993 ◽  
Vol 5 (4) ◽  
pp. 297-305 ◽  
Author(s):  
F P Glatz ◽  
R Mdiilhaupt
Keyword(s):  
Mechanical Properties ◽  
Polymer Networks ◽  
Interpenetrating Polymer Networks ◽  
Acid Anhydride ◽  
Resin System ◽  
Tetracarboxylic Acid ◽  
Interpenetrating Networks ◽  
Sulfur Containing ◽  
Phenylene Sulfide

Microphase-separated semi-interpenetrating polymer networks (semi-n Ns) were obtained by curing 4,4'-bismaleimidodiphenylmethane (BMII), which was advanced in situ with diamine-terminated oligo(phenylene sulfide) (PPS-DA), in the presence of a non-crosslinked linear high-T, aromatic polyether. Poly(thioether amide imide) (PTEAI) containing two phenylene sulfide units, Ultems 1000 poly(ether imide) (PEI) and benzophenone tetracarboxylic acid anhydride/diaminophenylindane polyimnide XU 218$ (PI) were used as non-crosslinked modifiers for the sulfur-containing BMI/PPS-DA resin system, which formed the continuous polymer matrix. Morphological and mechanical properties of the polyether-modified BMI/PPS-DA resin systems were investigated as a function of semi-n?,-compositions and polymer compatibilities. The soluble high-TA P1 gave improved strength and toughness without sacrificing the high T, of the resulting multiphase semi-iPNS.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1616
Author(s):  
Vincenzo Titone ◽  
Antonio Correnti ◽  
Francesco Paolo La Mantia
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Moisture Content ◽  
Mechanical Testing ◽  
Hydrolytic Degradation ◽  
Slight Reduction ◽  
Biodegradable Polyester ◽  
Molding Process ◽  
Elongation At Break ◽  
Effect Of Moisture

This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that the amount of absorbed water—both before processing and before mechanical testing—causes an increase in elongation at break and a slight reduction of the elastic modulus and tensile strength. These changes have been associated with possible hydrolytic degradation during the compression molding process and, in particular, with the plasticizing action of the moisture absorbed by the specimens.

Effect of Castor Oil Impregnation on the Physical and Mechanical Properties of Bacterial Cellulose

2012 ◽  
Vol 3 (1) ◽  
pp. 13-26
Author(s):  
Myrtha Karina ◽  
Lucia Indrarti ◽  
Rike Yudianti ◽  
Indriyati
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Young’S Modulus ◽  
Castor Oil ◽  
Young's Modulus ◽  
Physical And Mechanical Properties ◽  
Scanning Electron Micrographs ◽  
Elongation At Break ◽  
Acetone Water

The effect of castor oil on the physical and mechanical properties of bacterial cellulose is described. Bacterial cellulose (BC) was impregnated with 0.5–2% (w/v) castor oil (CO) in acetone–water, providing BCCO films. Scanning electron micrographs revealed that the castor oil penetrated the pores of the bacterial cellulose, resulting in a smoother morphology and enhanced hydrophilicity. Castor oil caused a slight change in crystallinity indices and resulted in reduced tensile strength and Young's modulus but increased elongation at break. A significant reduction in tensile strength and Young's modulus was achieved in BCCO films with 2% castor oil, and there was an improvement in elongation at break and hydrophilicity. Impregnation with castor oil, a biodegradable and safe plasticiser, resulted in less rigid and more ductile composites.

Properties of Random PSF/PES Copolymers as High-Performance Polymers

2011 ◽  
Vol 217-218 ◽  
pp. 1606-1610
Author(s):  
Dong Jiang ◽  
Xiao Ran Zhang ◽  
Yan Mei Ma ◽  
Cheng You Ma
Keyword(s):  
Weight Loss ◽  
Tensile Strength ◽  
Glass Transition ◽  
High Performance ◽  
Molar Ratio ◽  
Transition Temperatures ◽  
Elongation At Break ◽  
Glass Transition Temperatures ◽  
High Performance Polymers ◽  
Diphenyl Sulfone

A series of random polysulfone/polyethersulfone (PSF/PES) copolymers were synthesized by the polycondensation of 4, 4'-isopropylidendiphenol, 4, 4΄-dihyolroxy diphenyl sulfone and 4, 4'-dichlorodiphenyl sulfone in the presence of K2CO3. We obtained a series of copolymers by changing the molar ratio of 4, 4΄-dihyolroxy diphenyl sulfone and 4, 4'-isopropylidendiphenol (it was marked as the ratio of S:A). The copolymers have the similar solubility with polyethersulfone. They also have high glass transition temperatures (Tg: 199°C~229°C) and 5% weight loss temperatures (4, 4'-isopropylidendiphenol: 4, 4΄-dihyolroxy diphenyl sulfone=1:1, Td5=497°C). At the same time the elongation at break is much higher than that of PES, while the tensile strength is a little lower than that of PES.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

Thermal and mechanical properties of simultaneous and sequential full-interpenetrating polymer networks

2004 ◽  
Vol 370 (1-2) ◽  
pp. 288-292 ◽  
Author(s):  
A Bartolotta ◽  
G Di Marco ◽  
M Lanza ◽  
G Carini ◽  
G D’Angelo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Networks ◽  
Interpenetrating Polymer Networks ◽  
Thermal And Mechanical Properties

Studies on Nanostructured Polyurethane/Clay Interpenetrating Polymer Networks

2005 ◽  
Vol 475-479 ◽  
pp. 1001-1004
Author(s):  
Ninglin Zhou ◽  
Xiao Xian Xia ◽  
Li Li ◽  
Shao Hua Wei ◽  
Jian Shen
Keyword(s):  
Mechanical Properties ◽  
Polymer Networks ◽  
Testing Machine ◽  
Physical And Mechanical Properties ◽  
Interpenetrating Polymer Networks ◽  
Absorption Properties ◽  
Tensile Testing Machine ◽  
Swelling Agent ◽  
Silicate Layers ◽  
Polyurethane Matrix

A novel exfoliated polyurethane (PU)/clay Interpenetrating Polymer Networks (IPNs) nanocomposite has been synthesized with polyurethane and organoclay. MTPAC is used as swelling agent to treat Na-montmorillonite for forming organoclay. The results indicate that there is very good compatibility between organoclay and PU. Nanoscale silicate dispersion was analyzed by XRD. The mechanical properties of the nanocomposites have been measured by tensile testing machine. The nanocomposites show obviously improved physical and mechanical properties when compared with the pure polymer. Additionally, PU /MTPAC- clay shows lower water absorption properties than pure PU do. In addition, the reinforcing and intercalating mechanism of silicate layers in polyurethane matrix are discussed.

Sign in / Sign up

Export Citation Format

Share Document