scholarly journals The influence of decorative surface of commercial particleboards on the formaldehyde release measured by flask method

2018 ◽  
pp. 137-142
Author(s):  
Mladjan Popovic ◽  
Tijana Todorovic ◽  
Milanka Djiporovic-Momcilovic ◽  
Ivana Gavrilovic-Grmusa ◽  
Jasmina Popovic
Keyword(s):  
Formaldehyde Emission ◽  
The Other ◽  
Test Series ◽  
Test Results ◽  
Formaldehyde Content ◽  
Formaldehyde Release ◽  
Very High

The formaldehyde release and the formaldehyde content from the commercial particleboards were determined using the flask and perforator methods. Since the melamine faced boards were used in this research, the flask method was applied to evaluate how much the decorative surface (melamine impregnated paper) affects the test results in terms of reducing the formaldehyde emission from the samples. Hence, the flask method tests were performed simultaneously with one test series presenting the melamine faced samples, and the other one presenting the samples with sanded surface. Also, the decorative surface was sanded off from all of the test samples intended for formaldehyde content measurements using perforator method. During this research, it was found that by removing the decorative surface, the formaldehyde emission increased in the range from 12.6% to 16.6%, suggesting that the decorative surface acts as a barrier to formaldehyde emission even for the samples of such a small size used in the flask method. In addition, very high correlation, of 0,989 and 0,959, was found between the formaldehyde content values (perforator method) and the values of formaldehyde release from sanded and melamine faced samples, respectively.

Bit Swap Established on EOC for VDSL

2014 ◽  
Vol 513-517 ◽  
pp. 1170-1175
Author(s):  
Chen En Liu ◽  
Ping Li
Keyword(s):  
Rapid Development ◽  
The Other ◽  
Test Results ◽  
Digital Subscriber Line ◽  
Crosstalk Noise ◽  
Line System ◽  
Subscriber Line ◽  
High Bit Rate ◽  
The One ◽  
Very High

With the rapid development of VDSL (Very high-bit-rate Digital Subscriber Line) system, not all the tones have the same margin. In order to cope with the slowly-changing channel, Bit Swap is utilized to swap the tone pairs: the one has a high margin while the other one has a relatively low margin. Although the Bit Swap has been proposed before, there is no Bit Swap established on EOC and the proposed scheme also implements coarse and fine SNR margin tuning. The paper presents the architecture and process of Bit Swap based on EOC and also proposes the method to adjust the margin for tones calculated to be swapped. After thoroughly tested, the test results show that the proposed scheme functions well. Compared with the scheme without Bit Swap, it greatly improves the performance against crosstalk noise and can reduce the RS errors to zero.

Thrombotic Thrombocytopenic Purpura: Mechanism for Effectiveness of Plasmapheresis

1979 ◽  
Author(s):  
J. G. Kelton ◽  
P. B. Neame ◽  
I. Walker ◽  
A. G. Turpie ◽  
J. McBride ◽  
...  
Keyword(s):  
Platelet Count ◽  
Thrombotic Thrombocytopenic Purpura ◽  
The Other ◽  
Unknown Etiology ◽  
Normal Range ◽  
Antiplatelet Antibody ◽  
Thrombocytopenic Purpura ◽  
Serious Illness ◽  
Normal Platelet ◽  
Very High

Thrombotic thrombocytopenic purpura (TTP) is a rare but serious illness of unknown etiology. Treatment by plasmapheresis has been reported to be effective but the mechanism for benefit is unknown. We have investigated the effect of plasmapheresis in 2 patients with TTP by quantitating platelet associated IgG (PAIgG) levels prior to and following plasmapheresis. Both patients had very high levels of PAIgG at presentation (90 and A8 fg IgG/platelet respectively, normal 0-5). in both, the PAIgG levels progressively fell to within the normal range and the platelet count rose following plasmapheresis. One patient remained in remission with normal platelet counts and PAIgG levels. The other relapsed after plasmapheresis and the PAIgG level rose prior to the fall in platelet count. Plasmapheresis was repeated and resulted in normalization of both the platelet count and PAIgG level. It is suggested that plasmapheresis removes antiplatelet antibody or immune complexes which may be of etiological importance in this illness.

Adding an expansive agent to increase the toughness of steel fibre reinforced concrete

2019 ◽  
Vol 26 (4) ◽  
pp. 197-208
Author(s):  
Leo Gu Li ◽  
Albert Kwok Hung Kwan
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
The Other ◽  
Fibre Reinforced Concrete ◽  
Test Results ◽  
Compressive Properties ◽  
Shrinkage Cracking ◽  
Steel Fibre Reinforced Concrete ◽  
Expansive Agent ◽  
Concrete Matrix

Previous research studies have indicated that using fibres to improve crack resistance and applying expansive agent (EA) to compensate shrinkage are both effective methods to mitigate shrinkage cracking of concrete, and the additions of both fibres and EA can enhance the other performance attributes of concrete. In this study, an EA was added to fibre reinforced concrete (FRC) to produce concrete mixes with various water/binder (W/B) ratios, steel fibre (SF) contents and EA contents for testing of their workability and compressive properties. The test results showed that adding EA would slightly increase the superplasticiser (SP) demand and decrease the compressive strength, Young’s modulus and Poisson’s ratio, but significantly improve the toughness and specific toughness of the steel FRC produced. Such improvement in toughness may be attributed to the pre-stress of the concrete matrix and the confinement effect of the SFs due to the expansion of the concrete and the restraint of the SFs against such expansion.

Growth Characteristics of Activated Sludges Acclimated to para-Nitrophenol in Batch and Continuous Modes

1994 ◽  
Vol 29 (7) ◽  
pp. 327-333
Author(s):  
Y. Matsui ◽  
F. Yamaguchi ◽  
Y. Suwa ◽  
Y. Urushigawa
Keyword(s):  
Growth Characteristics ◽  
The Other ◽  
Operational Mode ◽  
Continuous Mode ◽  
Relative Resistance ◽  
Batch Mode ◽  
The Given ◽  
Operational Modes ◽  
Very High ◽  
Sensitive Group

Activated sludges were acclimated to p-nitrophenol (PNP) in two operational modes, a batch and a continuous. The operational mode of the PNP acclimation of activated sludges strongly affected the physiological characteristics of predominant microorganisms responsible for PNP degradation. Predominant PNP degraders in the sludge in batch mode (Sludge B) had lower PNP affinity and were relatively insensitive to PNP concentration. Those of the sludge in continuous mode (Sludge C), on the other hand, had very high PNP affinity and were sensitive to PNP. MPN enumeration of PNP degraders in sludge B and C using media with different PNP concentrations (0.05, 0.2,0.5 and 2.0 mM) supported the above results. Medium with 0.2 mM of PNP did not recover PNP degraders in sludge C well, while it recovered PNP degraders in sludge B as well as the medium with 0.05 mM did. When switching from one operational mode to the other, the predominant population in sludge B shifted to the sensitive group, but that of sludge C did not shift at the given loading of PNP, showing relative resistance to inhibitive concentration.

Islamic hedging for pilgrimage funds: case of Indonesia

2019 ◽  
Vol 11 (3) ◽  
pp. 328-341
Author(s):  
Rifki Ismal ◽  
Nurul Izzati Septiana
Keyword(s):  
Exchange Rate ◽  
The Other ◽  
Exchange Rate Risk ◽  
Content Type ◽  
Other Hand ◽  
Rate Risk ◽  
Risk Identify ◽  
Hajj Season ◽  
The Right ◽  
Very High

Purpose The demand for Saudi Arabian real (SAR) is very high in the pilgrimage (hajj) season while the authority, unfortunately, does not hedge the hajj funds. As such, the hajj funds are potentially exposed to exchange rate risk, which can impact the value of hajj funds and generate extra cost to the pilgrims. The purpose of this paper is to conduct simulations of Islamic hedging for pilgrimage funds to: mitigate and minimize exchange rate risk, identify and recommend the ideal time, amount and tenors of Islamic hedging for hajj funds, estimate cost saving by pursuing Islamic hedging and propose technical and general recommendations for the authority. Design/methodology/approach Forward transaction mechanism is adopted to compute Islamic forward between SAR and Rupiah (Indonesian currency) or IDR. Findings – based on simulations, the paper finds that: the longer the Islamic hedging tenors, the better is the result of Islamic hedging, the decreasing of IDR/USD is the right time to hedge the hajj funds and, on the other hand, the IDR/SAR appreciation is not the right time to hedge the hajj funds. Findings Based on simulations, the paper finds that: the longer the Islamic hedging tenors, the better is the result of Islamic hedging, the decreasing of IDR/USD is the right time to hedge the hajj funds and, on the other hand, the IDR/SAR appreciation is not the right time to hedge the hajj funds. Research limitations/implications The research suggests the authority to (and not to) hedge the hajj fund, depending on economic conditions and market indicators. Even though the assessment is for the Indonesian case, other countries maintaining hajj funds might also learn from this paper. Originality/value To the best of author’s knowledge, this is the first paper in Indonesia that attempts to simulate the optimal hedging of hajj funds.

scholarly journals Evaluating Presence/Absence of Target Microbes in Microbiological Tests

2000 ◽  
Vol 83 (6) ◽  
pp. 1429-1434
Author(s):  
Robert J Blodgett ◽  
Anthony D Hitchins
Keyword(s):  
Performance Studies ◽  
Collaborative Study ◽  
False Negative ◽  
The Other ◽  
Test Results ◽  
Logistic Curve ◽  
Microbiological Method ◽  
Test Portion ◽  
Method Performance ◽  
Data Set

Abstract A typical qualitative microbiological method performance (collaborative) study gathers a data set of responses about a test for the presence or absence of a target microbe. We developed 2 models that estimate false-positive and false-negative rates. One model assumes a constant probability that the tests will indicate the target microbe is present for any positive concentration in the test portion. The other model assumes that this probability follows a logistic curve. Test results from several method performance studies illustrate these estimates.

scholarly journals Effect of Fly Ash on Compressive Strength, Drying Shrinkage, and Carbonation Depth of Mortar with Ferronickel-Slag Powder

2021 ◽  
Vol 11 (3) ◽  
pp. 1037
Author(s):  
Se-Jin Choi ◽  
Ji-Hwan Kim ◽  
Sung-Ho Bae ◽  
Tae-Gue Oh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Bituminous Coal ◽  
Raw Materials ◽  
Drying Shrinkage ◽  
The Other ◽  
Test Results ◽  
Slag Powder ◽  
Ferronickel Slag

In recent years, efforts to reduce greenhouse gas emissions have continued worldwide. In the construction industry, a large amount of CO2 is generated during the production of Portland cement, and various studies are being conducted to reduce the amount of cement and enable the use of cement substitutes. Ferronickel slag is a by-product generated by melting materials such as nickel ore and bituminous coal, which are used as raw materials to produce ferronickel at high temperatures. In this study, we investigated the fluidity, microhydration heat, compressive strength, drying shrinkage, and carbonation characteristics of a ternary cement mortar including ferronickel-slag powder and fly ash. According to the test results, the microhydration heat of the FA20FN00 sample was slightly higher than that of the FA00FN20 sample. The 28-day compressive strength of the FA20FN00 mix was approximately 39.6 MPa, which was higher than that of the other samples, whereas the compressive strength of the FA05FN15 mix including 15% of ferronickel-slag powder was approximately 11.6% lower than that of the FA20FN00 mix. The drying shrinkage of the FA20FN00 sample without ferronickel-slag powder was the highest after 56 days, whereas the FA00FN20 sample without fly ash showed the lowest shrinkage compared to the other mixes.

Rolling and Recrystallization Textures in High Purity Al Cold Rolled to Very High Rolling Reductions

2005 ◽  
Vol 495-497 ◽  
pp. 603-608 ◽  
Author(s):  
Atsushi Todayama ◽  
Hirosuke Inagaki
Keyword(s):  
Cold Rolling ◽  
High Purity ◽  
Work Hardening ◽  
Dynamic Recovery ◽  
The Other ◽  
Rolling Reduction ◽  
Theoretical Investigations ◽  
Theoretical Predictions ◽  
Cold Rolled ◽  
Very High

On the basis of Taylor-Bishop-Hill’s theory, many previous theoretical investigations have predicted that, at high rolling reductions, most of orientations should rotate along theβfiber from {110}<112> to {123}<634> and finally into the {112}<111> stable end orientations. Although some exceptions exist, experimental observations have shown, on the other hand, that the maximum on the β fiber is located still at about {123}<634> even after 97 % cold rolling. In the present paper, high purity Al containing 50 ppm Cu was cold rolled up to 99.4 % reduction in thickness and examined whether {112}<111> stable end orientation could be achieved experimentally. It was found that, with increasing rolling reduction above 98 %, {110}<112> decreased, while orientations in the range between {123}<634> and {112}<111> increased, suggesting that crystal rotation along the βfiber from {110}<112> toward {123}<634> and {112}<111> in fact took place. At higher rolling reductions, however, further rotation of this peak toward {112}<111> was extremely sluggish, and even at the highest rolling reduction, it could not arrive at {112}<111>. Such discrepancies between theoretical predictions and experimental observations should be ascribed to the development of dislocation substructures, which were formed by concurrent work hardening and dynamic recovery. Since such development of dislocation substructures are not taken into account in Taylor-Bishop-Hill’s theory, it seems that they can not correctly predict the development of rolling textures at very high rolling reductions, i. e. stable end orientations. On annealing specimens rolled above 98 % reduction in thickness, cube textures were very weak, suggesting that cube bands were almost completely rotated into other orientations during cold rolling. {325}<496>, which lay at an intermediate position between {123}<634> and {112}<111> along theβfiber, developed strongly in the recrystallization textures.

LONG DURATION ECHOES FROM AURORA, METEORS, AND IONOSPHERIC BACK-SCATTER

1953 ◽  
Vol 31 (2) ◽  
pp. 171-181 ◽  
Author(s):  
D. W. R. McKinley ◽  
Peter M. Millman
Keyword(s):  
Long Range ◽  
High Frequency ◽  
The Other ◽  
Very High Frequency ◽  
Long Duration ◽  
E Region ◽  
Very High ◽  
Visual Observations

In the course of the Ottawa meteor program some unusual echoes have been detected on 33 Mc. Echoes from the aurora are discussed and correlated with visual observations. Two mechanisms of radio reflections from the aurora have been proposed but the data here presented are insufficient to favor one over the other. On Aug. 4, 1948, six extremely long duration meteor echoes were observed which may have been due to abnormal ionospheric conditions. From time to time since August, 1948, a weak semipermanent echo has been recorded, usually appearing at a range of about 80 km., and enduring up to an hour. It is suggested that this echo is due to back-scatter from the same sources in the lower E-region that are presumed to be responsible for long-range very high frequency propagation.

scholarly journals Generation of an EDS Key Based on a Graphic Image of a Subject’s Face Using the RC4 Algorithm

Information ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 19
Author(s):  
Alexey Semenkov ◽  
Dmitry Bragin ◽  
Yakov Usoltsev ◽  
Anton Konev ◽  
Evgeny Kostuchenko
Keyword(s):  
Image Recognition ◽  
Random Number ◽  
Statistical Test ◽  
The Other ◽  
Test Results ◽  
Random Generation ◽  
Facial Image ◽  
Random Number Generators ◽  
Graphic Image ◽  
High Level

Modern facial recognition algorithms make it possible to identify system users by their appearance with a high level of accuracy. In such cases, an image of the user’s face is converted to parameters that later are used in a recognition process. On the other hand, the obtained parameters can be used as data for pseudo-random number generators. However, the closeness of the sequence generated by such a generator to a truly random one is questionable. This paper proposes a system which is able to authenticate users by their face, and generate pseudo-random values based on the facial image that will later serve to generate an encryption key. The generator of a random value was tested with the NIST Statistical Test Suite. The subsystem of image recognition was also tested under various conditions of taking the image. The test results of the random value generator show a satisfactory level of randomness, i.e., an average of 0.47 random generation (NIST test), with 95% accuracy of the system as a whole.

Sign in / Sign up

Export Citation Format

Share Document