scholarly journals On engineering of properties of wood-polypropylene composite

2006 ◽  
pp. 59-70 ◽  
Author(s):  
Milanka Djiporovic ◽  
Jovan Miljkovic ◽  
Eva Dingova
Keyword(s):  
Tensile Strength ◽  
Filler Content ◽  
Wood Flour ◽  
Beech Wood ◽  
Impact Resistance ◽  
High Strength ◽  
Polypropylene Composite ◽  
Elongation At Break ◽  
New Type ◽  
Polypropylene Matrix

New materials based on wood have the advantage in the sense that their properties can be engineered so as to correspond to user demands. The properties which can be engineered are those relating both to their utilisation and machining, in particular - the tensile strength, elongation at break, modulus of elasticity and impact resistance. The research at the Faculty of Forestry and "Hipol" Chemical Industry related to the new type of wood-polypropylene composite. The content of wood filler was varied in the range between 40% and 70% mass contents of beech wood flour. After the highest tensile strength at 50% of filler content was determined, the effect of the wood filler origin was also examined at this content value. Therefore, wood flour of beech, poplar, acetylated pine and the waste MDF was used. The influence of the composition of the wood filler (beech combined with MDF, poplar and acetylated pine) in comparison with pure polypropylene matrix was also examined, as well as the effect of the type of coupling agent. Hopefully, the results obtained in this study might serve as the initial data for production of easily machined high-strength composites.

Graphite/Bio-Based Epoxy Composites: The Mechanical Properties Interface

2015 ◽  
Vol 799-800 ◽  
pp. 115-119 ◽  
Author(s):  
Anika Zafiah M. Rus ◽  
Nur Munirah Abdullah ◽  
M.F.L. Abdullah ◽  
M. Izzul Faiz Idris
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Filler Content ◽  
Weight Percent ◽  
Epoxy Composites ◽  
Elongation At Break ◽  
Graphite Content ◽  
Dispersion Condition ◽  
Strong Interfacial Bonding

Graphite reinforced bio-based epoxy composites with different particulate fractions of graphite were investigated for mechanical properties such as tensile strength, elastic modulus and elongation at break. The graphite content was varied from 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.%, 30 wt.% by weight percent in the composites. The results showed that the mechanical properties of the composites mainly depend on dispersion condition of the treated graphite filler, aggregate structure and strong interfacial bonding between treated graphite in the bio-based epoxy matrix. The composites showed improved tensile strength and elastic modulus with increase treated graphite weight loading. This also revealed the composites with increasing filler content was decreasing the elongation at break.

Preparation and characterizations of ternary biodegradable blends composed of polylactide, poly(ε-caprolactone), and wood flour

2012 ◽  
Vol 32 (6-7) ◽  
pp. 435-444 ◽  
Author(s):  
Hsin-Tzu Liao ◽  
Chin-San Wu
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Tensile Strength ◽  
Fourier Transform ◽  
Wood Flour ◽  
High Price ◽  
Infrared Analysis ◽  
Melt Blending ◽  
Ternary Blends ◽  
Elongation At Break

Abstract Melt blending of polylactide (PLA), poly(ε-caprolactone) (PCL), and wood flour (WF) was performed in an effort to overcome the major drawbacks (brittleness and high price) of PLA. In addition, the acrylic acid (AA)-grafted PLA70PCL30 (PLA70PCL30-g-AA) was used as the alternative for the preparation of ternary blends to improve the compatibility and the dispersability of WF within the PLA70PCL30 matrix. As expected, PCL improved the elongation at break and the toughness of PLA but decreased the tensile strength and modulus. Because the hydrophilic WF is dispersed physically in the hydrophobic PLA70PCL30 matrix, as the result of Fourier transform infrared analysis, the mechanical properties of PLA70PCL30 became noticeably worse when it was blended with WF. This problem was successfully conquered by using PLA70PCL30-g-AA to replace PLA70PCL30 due to the formation of an ester carbonyl group between PLA70PCL30-g-AA and WF. Furthermore, the PLA70PCL30-g-AA/WF blend provided a plateau tensile strength at break when the WF content was up to 50 wt%. PLA70PCL30/WF exhibited a tensile strength at break of approximately 3–25 MPa more than PLA70PCL30-g-AA/WF. By using p-cresol and tyrosinase, the enzymatic biodegradable test showed that PLA70PCL30-g-AA is somewhat more biodegradable than PLA70PCL30 because the former has better water absorption. After 16 weeks, the weight loss of the PLA70PCL30/WF (50 wt%) composite was >80%. PLA70PCL30-g-AA/WF exhibited a weight loss of approximately 1–12 wt% more than PLA70PCL30-g-AA/WF. It was also found that the addition of WF to PLA70PCL30 or PLA70PCL30-g-AA decreased the crystallinity of PLA and PCL in PLA70PCL30 or PLA70PCL30-g-AA and then increased their biodegradable property.

The Development of Annealing Time for Super Fine Grain and High Strength IF Steel

2013 ◽  
Vol 631-632 ◽  
pp. 613-616 ◽  
Author(s):  
Hong Mei Zhang ◽  
Li Feng Qiao
Keyword(s):  
Tensile Strength ◽  
High Strength ◽  
Strain Ratio ◽  
Continuous Annealing ◽  
High Tensile Strength ◽  
Plastic Strain Ratio ◽  
Fine Grain ◽  
New Type ◽  
High Strength If Steel ◽  
Annealing Experiments

The hot rolling, cold rolling and simulative continuous annealing experiments were carried out in the laboratory on the base of new type SFG HSS (super fine grain, high strength steel sheet). The results show that the microstructure which contains a number of cake shaped grain can be refined and homogenized by the feasible annealing holding time. Contrast to the conventional steel, the SFG steel have the characters of super fine grain, high tensile strength, low yield strength/tensile strength rate, good elongation and high r-value high（the plastic strain ratio）．

Tensile Properties and Morphology of Low Linear Density Polyethylene/Kapok Husk Eco-Composites

2015 ◽  
Vol 754-755 ◽  
pp. 161-165
Author(s):  
Nurul Fatin Syazwani binti Arshad ◽  
Salmah Husseinsyah ◽  
Lim Bee Ying
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Modulus Of Elasticity ◽  
Interfacial Adhesion ◽  
Linear Density ◽  
Filler Content ◽  
Rotor Speed ◽  
Elongation At Break ◽  
Morphology Study

This research focused on the utilization of kapok husk (KH) as filler in low linear density polyethylene (LLDPE). The effect of filler content on tensile properties and morphology of LLDPE/KH eco-composites were investigated. The eco-composites were prepared by using Brabender Plasticiser EC Plus at temperature 160 °C and rotor speed 50 rpm. The results indicated that the tensile strength and elongation at break decreased with KH content increased. However, the modulus of elasticity increased with increasing of KH content. The morphology study of eco-composites exhibit poor interfacial adhesion between KH and LLDPE.

scholarly journals Utilization of melamine impregnated paper waste as a filler in thermoplastic composites

BioResources ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. 3159-3170
Author(s):  
Fatma Bozkurt ◽  
Büşra Avci ◽  
Fatih Mengeloğlu
Keyword(s):  
Mechanical Properties ◽  
Filler Content ◽  
Wood Flour ◽  
Environmental Benefits ◽  
Thermoplastic Composites ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Composite Manufacturing ◽  
Elongation At Break ◽  
Molding Method

The potential utilization of melamine impregnated paper (MIP) waste in thermoplastic composites was investigated. Composites were also manufactured utilizing wood flour (WF) at the same filler rates for comparison. The composites were manufactured using a compression molding method. The effects of filler type and filler rate on the mechanical properties of low-density polyethylene (LDPE)-based composites were evaluated. Mechanical properties, such as tensile and flexural strengths, were determined in accordance with ASTM D638 (2001) and ASTM D790 (2003), respectively. Results showed that filler type and filler content had significant effects on all mechanical properties investigated. Both fillers improved all mechanical properties except for tensile strength and elongation at break of LDPE. In conclusion, MIP waste has a potential to be utilized in thermoplastic-based composite manufacturing and might generate some economic and environmental benefits.

Direct Reactive Compatibilization of GMA on PE/Wood-Flour Composite

2011 ◽  
Vol 378-379 ◽  
pp. 735-739
Author(s):  
Yue Wen Li ◽  
Xin Hua Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Reactive Extrusion ◽  
Rupture Surface ◽  
Elongation At Break ◽  
Reactive Compatibilization ◽  
Anchoring Strength

Reactive compatibilization between high-density polyethylene(HDPE) and wood-flour was achieved via direct reactive extrusion of glycidyl methacrylate(GMA), initiator, HDPE and wood-flour. Impact rupture surface of the composite was observed by scanning electron microscope(SEM), and its load deformation temperature(HDT) and mechanical properties were tested. Effect of GMA dosage and extrusion temperature on reactive compatibilization of the composite was analysed. The result indicated that the anchoring strength of interface in the composite was obviously strengthened, and its HDT, tensile strength, flexural strength, notched impact strength and elongation at break of the composite were distinctly improved due to the addition of GMA and dicumyl peroxide(DCP). When the composite was extruded at 180°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 45Mpa, 11% and 6.6KJ.m-2, which respectively increased by 17°C, 74%, 36%, 83% and 69% than that of the composite without reactive compatibilization, and when the composite was extruded at 190°C, the peak values of its HDT, tensile strength, flexural strength, elongation at break and notched impact strength respectively were 84°C, 40Mpa, 44Mpa, 11% and 6.6KJ.m-2, which respectively increased by 20°C, 60%, 26%, 83% and 83% than that of the composite without reactive compatibilization. When GMA usage increased, the HDT and mechanical properties of the composite increased first, then descended, and the optimum usage of GMA was 1wt%-3wt%.

The Effect of Silica Nanofiller on the Physical and Thermal Characteristics of Rubber-Based Composites

2021 ◽  
Vol 36 (1) ◽  
pp. 60-68
Author(s):  
A. Chelli ◽  
L. Hemmouche ◽  
H. Ait-Sadi ◽  
D. Trache ◽  
M. Benziane ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Catalytic Effect ◽  
Filler Content ◽  
Thermal Analyses ◽  
Thermal Characteristics ◽  
Butadiene Rubber ◽  
Nano Silica ◽  
Scanning Calorimetry ◽  
Elongation At Break ◽  
Tear Strength

Abstract The use of nano composites in elastomer blends gives outstanding mechanical properties compared to the use of micro and macro composites, even with very low nano filler content. In this paper, we studied the influence of varying proportions of natural rubber (NR) and acrylonitrile butadiene rubber (NBR) reinforced with nano silica on the mechanical and thermal characteristics of the rubber. Mechanical characterizations were carried out with hardness, tensile strength, elongation at break, tear strength, modulus and toughness. For thermal analyses, we used differential scanning calorimetry ( DSC) and Thermogravimetric Analysis (TGA). In most cases, the increase in the percentage of NBR with the presence of nano silica enhances hardness, modulus and toughness, however, it reduces tensile strength, tear strength and elongation at break. It was found that nano silica has a catalytic effect on the mixture, and NBR has a catalytic effect on the decomposition of NR.

Effect of wood particle size on selected properties of neat and recycled wood polypropylene composites

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 3427-3442
Author(s):  
Vedat Çavuş ◽  
Fatih Mengeloğlu
Keyword(s):  
Particle Size ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Wood Particle ◽  
Sem Analysis ◽  
Elongation At Break

Neat polypropylene (PP)- and post-industrial recycled polypropylene (rPP)-based wood-plastic composites (WPC) were manufactured using 40% mahogany wood flour (WF). The effect of particle size (0.074 to 0.149 mm, 0.177 to 0.250 mm, and 0.400 to 0.841 mm) on the selected properties of PP and rPP composites was studied. The influence of 3% maleic anhydride grafted polypropylene (MAPP) presence in the formulation was also evaluated. Test specimens were manufactured using a combination of extrusion and injection molding processes. The density and mechanical properties, such as flexural strength, flexural modulus, tensile strength, tensile modulus, elongation at break, hardness and impact strength values were determined. Morphology of the manufactured composites was also studied using scanning electron microscopy (SEM) analysis. Results showed that the particle size, polypropylene type (neat or recycled), and presence of MAPP had important effects on WPC’s properties. Density, flexural modulus, tensile modulus, and impact strength values increased with decreased particle size regardless of the presence of MAPP. Flexural strength values increased with decreased particle size without MAPP. Regardless of particle size, addition of MAPP in composites provided higher flexural strength, flexural modulus, tensile strength, and tensile modulus values but lower elongation at break values compared to composites without MAPP.

Mechanical properties of polypropylene/glass weft knitted composites hot pressed in various structures and contents

2013 ◽  
Vol 20 (1) ◽  
pp. 67-73 ◽  
Author(s):  
Dariush Semnani ◽  
Ali Zadhoush ◽  
Matin Mashayekhi
Keyword(s):  
Mechanical Properties ◽  
Impact Resistance ◽  
High Strength ◽  
Hot Press ◽  
Knitted Fabrics ◽  
Manufacturing Method ◽  
Maximum Stiffness ◽  
Bending Resistance ◽  
Press Method ◽  
Polypropylene Matrix

AbstractIn this study, composites of knitted fabric made from side-by-side multiple glass and polypropylene yarns have been investigated. These composites have been produced by a new manufacturing method – the hot press method. By using various knitted fabrics made from different components of glass and polypropylene yarns, several types of knitted structures and yarn components were investigated: rib 1-1, full Milano and full cardigan. The mechanical properties of composites were measured in three directions. The results showed that hot-pressed knitted composites of glass and polypropylene yarns have high strength, impact resistance, work-to-break and elongation, simultaneously. The highest bending resistance and maximum stiffness are achieved for rib-knitted composites consisting of 8 wt% glass and 92 wt% polypropylene yarns. The highest impact energy absorption was obtained with 18 wt% glass content and 82 wt% polypropylene matrix.

scholarly journals Ultraflexible and Mechanically Strong Polymer/Polyaniline Conductive Interpenetrating Nanocomposite via In Situ Polymerization of Vinyl Monomer

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2159
Author(s):  
Haihua Wang ◽  
Xiaojing Wu ◽  
Xuan Qin ◽  
Guiqiang Fei ◽  
Liyu Sun ◽  
...  
Keyword(s):  
Tensile Strength ◽  
In Situ Polymerization ◽  
Conductive Polymer ◽  
High Strength ◽  
Polymer Nanocomposite ◽  
Vinyl Monomer ◽  
Elongation At Break ◽  
Conductive Polyaniline ◽  
High Flexibility

Simultaneous enhancement of conductivity and mechanical properties for polyaniline/polymer nanocomposite still remains a big challenge. Here, a reverse approach via in situ polymerization (RIP) of vinyl monomers in waterborne polyaniline dispersion was raised to prepare conductive polyaniline (GPANI)/polyacrylate (PMB) interpenetrating polymer (GPANI-PMB) nanocomposite. GPANI/PMB physical blend was simultaneously prepared as reference. The conductive GPANI-PMB nanocomposite film with compact pomegranate-shape morphology is homogeneous, ultraflexible and mechanically strong. With incorporating a considerable amount of PMB into GPANI via the RIP method, only a slight decrease from 3.21 to 2.80 S/cm was detected for the conductivity of GPANI-PMB, while the tensile strength significantly increased from 25 to 43.5 MPa, and the elongation at break increased from 40% to 234%. The water absorption of GPANI-PMB3 after 72 h immersion decreased from 24.68% to 10.35% in comparison with GPANI, which is also higher than that of GPANI/PMB. The conductivity and tensile strength of GPANI-PMB were also much higher than that of GPANI/PMB (0.006 S/cm vs. 5.59 MPa). Moreover, the conductivity of GPANI-PMB remained almost invariable after folding 200 times, while that of GPANI/PMB decreased by almost half. This RIP approach should be applicable for preparing conventional conductive polymer nanocomposite with high conductivity, high strength and high flexibility.

Sign in / Sign up

Export Citation Format

Share Document