scholarly journals Experimental model for energy efficiency examination of pneumatic system

2011 ◽  
Vol 24 (1) ◽  
pp. 21-30
Author(s):  
Vladislav Blagojevic ◽  
Miodrag Stojiljkovic ◽  
Vlastimir Nikolic

In pneumatic systems, which represent large energy consumers, energy saving is very important. Mostly, the costs of the electric power used for feeding the compressors in the production of compressed air amount to around 20% of the overall costs of electrical power for some factory. In order to examine energy efficiency of conventional pneumatic system as well as servo system, no matter on actuator type, in this paper the new experimental model for energy efficiency examination is proposed. It consists of two important parts, such as electric and pneumatic part. The conducted experiments have demonstrated that this new experimental model provides satisfactory results of actuator positioning and energy efficiency as well.

2009 ◽  
Vol 13 (1) ◽  
pp. 185-193 ◽  
Author(s):  
Dusan Gordic ◽  
Milun Babic ◽  
Dubravka Jelic ◽  
Davor Koncalovic ◽  
Nebojsa Jovicic ◽  
...  

This paper deals with energy audit procedure implemented on only Serbian car manufacturer 'Zastava Automobili'. Based on the results of energy auditing and performed technological and economical feasibility studies several energy saving measures were proposed. The measures are related to different energy sources: steam, hot water, compressed air, electricity, and water. Such energy efficiency programs reduce energy costs and increase production profitability of the factory.


2014 ◽  
Vol 628 ◽  
pp. 225-228
Author(s):  
Xiao Lin Tian ◽  
Shou Gen Hu ◽  
Hong Bo Qin ◽  
Jun Zhao ◽  
Ling Yuan Ran

As the most widely used fourth energy, compressed air system has high operating costs. The research about energy consumption and energy optimization measures of compressed air system has become the new field to achieve energy saving among countries all over the world. In recent years, air compressor system researches in energy consumption, influence factors, energy saving technologies and energy efficiency evaluation have been carried out at home and abroad, and some achievements have been achieved. This paper summarizes energy consumption research status of air compressor system at home and abroad, and energy-saving technologies of compressed air in generation link, treatment link and gas link, and energy efficiency evaluation methods for of air compressor systems. Potentials and drawbacks of current researches are analyzed simultaneously. In the end energy-saving development directions of air compressor system are predicted.


Actuators ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 125
Author(s):  
Milan Šešlija ◽  
Vule Reljić ◽  
Dragan Šešlija ◽  
Slobodan Dudić ◽  
Nikolina Dakić ◽  
...  

In order to improve the energy efficiency of multi-actuator pneumatic systems, a control scheme for the recovery of exhausted compressed air is designed and studied herein. This paper explains the procedure for the development of the balanced operation of a multi-actuator pneumatic system through the collection and reuse of exhausted compressed air. Compared with traditional motion control of pneumatic actuators, significant energy savings can be achieved, while the dynamic behavior of the cylinders from which the exhausted air is collected is maintained.


2016 ◽  
Vol 856 ◽  
pp. 82-90
Author(s):  
Christian Sand ◽  
Matthias Seidl ◽  
Christian Leinauer ◽  
Maximilian Neuner ◽  
Moritz Meiners ◽  
...  

Modern assembly lines are usually optimized towards output and tact time as well as process capability and quality. Yet, approaches for energy saving are hardly used in assembly presses. Therefore, assembly lines are using more electric power and compressed air than necessary. Especially at high load, during handling phases and in different idle modes there is a huge potential for energy savings. Current research is focusing on high-power consuming turning and milling machines as well as laser welding. Energy saving projects usually focus on whole factory halls instead of manufacturing lines and single assembly machines. Therefore, this paper presents a new methodology using a top-down-approach and data mining analysis regarding a conventional assembly press as well as a whole assembly line. Here, relevant information types like process data, quality factors, expenditure of energy per produced part and power consumption are used to generate more insight into chained assembly processes. Various tools like energy analysis, process flow and correlation analysis are used to identify focus stations of a whole assembly line for energy saving projects and quality improvements. This novel holistic approach regards the electrical power and compressed air consumption of each relevant station and its machine components during different operating states as well as its correlations between process data, quality factors and energy consumption. Besides tact-time-analysis of the process, the scheduled and unplanned downtimes of the machine are also regarded. Furthermore, it enables predictions of tool wear and breakdown, quality impacts of supplied parts, as well as energy savings on process and machine level. Due to an increased quality, the material efficiency may rise as well.


2010 ◽  
Vol 34-35 ◽  
pp. 551-556 ◽  
Author(s):  
Chong Liu ◽  
Mao Lin Cai

This paper proposes a representation and measurement method for compressed air power widely used by various industries in the industrial. It proposes an accurate and standardized way to represent and measure the power energy in unit time of the flow compressed air, then establishes the evaluation system in energy distribution, loss and use in pneumatic system, which can clear the energy loss in pneumatic system and its components. Pneumatic power transducer designed in accordance with pneumatic power, it has advanced functions and higher precision, which can promote the energy efficiency greatly in pneumatic system.


2018 ◽  
Vol 14 (2) ◽  
pp. 9-14 ◽  
Author(s):  
Tomáš Skrúcaný ◽  
Saša Milojević ◽  
Štefánia Semanová ◽  
Tomáš Čechovič ◽  
Tomasz Figlus ◽  
...  

Abstract The article deals with the problem of electric power production in terms of environmental impact, in particular the energy efficiency of its production to utilize primary sources. The efficiency of its production directly depends on the composition of primary sources and technologies used. Difference in efficiency by converting various forms of energy into electrical power and their ratio in the use directly affect the resulting efficiency, production of emissions and thus the environmental impact. Electric traction, its production, is burdened less efficient than other types of tractions used in transport, but at the final reconciliation of their consumption in vehicles, this difference decreases or delays because the vehicles themselves work with different conversion efficiency of its traction on mechanical work, vehicle driving.


Author(s):  
Ivan M. Gryshchenko ◽  
Liudmyla M. Hanushchak-Yefimenko ◽  
Valeriia G. Scherbak ◽  
Оleksii Yu. Volianyk

This study attempts to address the issues of enhancing energy efficiency using mathematical modeling methods. The research findings assert that energy saving is a new challenging task of the 21st century, since thermal and electric power consumption is essential to human life and building a favourable living environment. It is observed that boosting the competitiveness, financial stability, energy and environmental security of Ukraine’s economy, as well as improving the living standards and the life quality seem hardly possible without realizing the energy saving potential and increasing energy efficiency through modernization, technological advancements and the transition towards rational and environmentally responsible utilization of energy resources. It is argued that by resolving the above objectives, Ukraine might strengthen its positions among developed economies. The following methods were used to carry out mathematical modeling to enhance the university energy efficiency in the frameworks of the energy knowledge hub: neural network technologies, mean absolute and relative error, mean absolute deviation; statistical comparison of the forecast accuracy based on the mean absolute error, as well as time series forecasting. A model to boost the University energy efficiency has been developed within the knowledge energy hub by implementing neural network patterns based on the experimental data from the Kyiv National University of Technologies and Design for the heating period 2020–2021. In particular, to optimize the operating modes of automatic power supply control for University Building 4, mathematical models with a complex algorithm structure have been employed (offering the increased resource intensity of such tasks). It is argued that making a decision on the feasibility of using an energy hub for University buildings and selecting appropriate equipment should be accomplished with due regard to the structure and the capacity of energy consumers, their types, demands for quality and reliability of electric power supply, their compliance with operating and safety standards, as well as taking into account the results of climate, wind monitoring and monitoring of solar activity. The conclusions resume that to assure the energy quality and the system sustainability, it is considered important to resolve a range of issues related to inconsistency in generation and supply of renewable energy from power plants, ensuring reliability and quality of energy supply through the use of energy storage (batteries) in particular, etc.).


Author(s):  
Marat R. Lukmanov ◽  
◽  
Sergey L. Semin ◽  
Pavel V. Fedorov ◽  
◽  
...  

The challenges of increasing the energy efficiency of the economy as a whole and of certain production sectors in particular are a priority both in our country and abroad. As part of the energy policy of the Russian Federation to reduce the specific energy intensity of enterprises in the oil transportation system, Transneft PJSC developed and implements the energy saving and energy efficiency improvement Program. The application of energy-saving technologies allowed the company to significantly reduce operating costs and emissions of harmful substances. At the same time, further reduction of energy costs is complicated for objective reasons. The objective of this article is to present additional methods to improve the energy efficiency of oil transportation by the example of the organizational structure of Transneft. Possibilities to reduce energy costs in the organization of the operating services, planning and execution of work to eliminate defects and preparatory work for the scheduled shutdown of the pipeline, the use of pumping equipment, including pumps with variable speed drive, the use of various pipelines layouts, changing the volume of oil entering the pipeline system and increase its viscosity.


Sign in / Sign up

Export Citation Format

Share Document