scholarly journals Removal of acridine orange dye from aqueous solution by adsorption onto dried sugar beet pulp

2017 ◽  
pp. 307-314
Author(s):  
Vesna Vucurovic ◽  
Vladimir Puskas ◽  
Uros Miljic
Keyword(s):  
Sugar Beet ◽  
Acridine Orange ◽  
Low Cost ◽  
Sugar Beet Pulp ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Equilibrium Data ◽  
Beet Pulp ◽  
Pseudo Second Order

A simple, low cost, and effective method for the removal of acridine orange (AO), a mutagenic cationic dye, from aqueous model solutions by adsorption onto dried sugar beet pulp (SBP) was evaluated in the present study. The AO removal was enhanced along with the increase of the initial solution pH and dye concentration. It was found that the adsorption process closely follows a pseudo-second-order chemisorption kinetics. The obtained equilibrium data obey both the Freundlich and Langmuir isotherm models. The SBP was proved to be very promising adsorbent for AO removal. Maximum adsorption capacity of the Langmuir monolayer of SBP for AO was found to be 5.37, 34.6, 89.62, 144.53 and 324.58 mg/g, at 25?C for the solution pH of 2, 4, 5, 6, and 8, respectively.

Kinetic and thermodynamic study of the adsorption of calcium onto sugar beet pulp

2016 ◽  
pp. 565-570
Author(s):  
Huang Qin ◽  
Zhu Si-ming ◽  
Zeng Di ◽  
Yu Shu-juan
Keyword(s):  
Sugar Beet ◽  
Adsorption Equilibrium ◽  
Ph Value ◽  
Hard Water ◽  
Sugar Beet Pulp ◽  
Order Kinetic ◽  
Factors Affecting ◽  
Isotherm Equation ◽  
Equilibrium Data ◽  
Beet Pulp

Sugar beet pulp (SBP) was used as low value adsorbent for the removal of calcium from hard water. Batch experiments were conducted to determine the factors affecting adsorption of the process such as pH value and Ca concentration. The adsorption equilibrium of Ca2+ by the SBP is reached after 100min and a pseudo second-order kinetic model can describe the adsorption process. The initial concentrations of Ca varied from 927 to 1127mgCa2+/L. A dose of 30g/L sugar beet pulp was sufficient for the optimum removal of calcium. The overall uptake of Ca ions by sugar beet pulp has its maximum at pH=8. The adsorption equilibrium data fitted well with the Langmuir adsorption isotherm equation.

A low-cost method for obtaining high-value bio-based propylene glycol from sugar beet pulp

RSC Advances ◽  
2015 ◽  
Vol 5 (3) ◽  
pp. 2299-2304 ◽  
Author(s):  
J. Berlowska ◽  
M. Binczarski ◽  
M. Dudkiewicz ◽  
H. Kalinowska ◽  
I. A. Witonska ◽  
...  
Keyword(s):  
Sugar Beet ◽  
Propylene Glycol ◽  
Low Cost ◽  
Sugar Beet Pulp ◽  
Beet Pulp

A new low-cost pathway for the production of high-value propylene glycol (PG) is proposed.

scholarly journals Utilization to Remove Pb (II) Ions from Aqueous Environments Using Waste Fish Bones by Ion Exchange

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Bayram Kizilkaya ◽  
A. Adem Tekınay
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Mechanism ◽  
Cost Effective ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Fish Bones ◽  
Adsorption Capacities ◽  
Aqueous Environments ◽  
Equilibrium Data ◽  
Pseudo Second Order

Removal of lead (II) from aqueous solutions was studied by using pretreated fish bones as natural, cost-effective, waste sorbents. The effect of pH, contact time, temperature, and metal concentration on the adsorption capacities of the adsorbent was investigated. The maximum adsorption capacity for Pb (II) was found to be 323 mg/g at optimum conditions. The experiments showed that when pH increased, an increase in the adsorbed amount of metal of the fish bones was observed. The kinetic results of adsorption obeyed a pseudo second-order model. Freundlich and Langmuir isotherm models were applied to experimental equilibrium data of Pb (II) adsorption and the value ofRLfor Pb (II) was found to be 0.906. The thermodynamic parameters related to the adsorption process such asEa,ΔG°,ΔH°, andΔS° were calculated andEa,ΔH°, andΔS° were found to be 7.06, 46.01 kJ mol−1, and 0.141 kJ mol−1K−1for Pb (III), respectively.ΔH° values (46.01 kJmol−1) showed that the adsorption mechanism was endothermic. Weber-Morris and Urano-Tachikawa diffusion models were also applied to the experimental equilibrium data. The fish bones were effectively used as sorbent for the removal of Pb (II) ions from aqueous solutions.

scholarly journals Simultaneous Adsorption of Cr(VI) and Phenol from Binary Mixture Using Iron Incorporated Rice Husk: Insight to Multicomponent Equilibrium Isotherm

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Ankur Gupta ◽  
Chandrajit Balomajumder
Keyword(s):  
Experimental Data ◽  
Rice Husk ◽  
Low Cost ◽  
Binary Solution ◽  
Multicomponent System ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Adsorption Isotherm Models ◽  
Pseudo Second Order

Fe modified rice husk was prepared as a low cost biosorbent for the removal of Cr(VI) and phenol both singly and in combination from single and binary simulated synthetic waste water. Rice husk was modified by treating with FeSO4·7H2O. The results showed that impregnation of iron onto the surface of rice husk improved the adsorption capability of both Cr(VI) and phenol. The effects of process parameters for multicomponent system such as pH, adsorbent dose, and contact time onto the percentage removal of both Cr(VI) and phenol were investigated. The experimental data for the adsorption of both Cr(VI) and phenol onto the surface of Fe modified rice husk applied to various kinetic and adsorption isotherm models. Multicomponent isotherm models such as Nonmodified Langmuir, Modified Langmuir, Extended Langmuir, Extended Freundlich, Competitive Nonmodified Redlich Peterson, Competitive Modified Redlich Peterson were applied. The results show that Extended Freundlich model best described the experimental data for both Cr(VI) and phenol from binary solution. Pseudo second-order model agreed well with Cr(VI) while pseudo first-order model agreed well with phenol. Maximum adsorption capacity in synthetic binary solution of Cr(VI) and phenol was found to be 36.3817 mg g−1for Cr(VI) and 6.569 mg g−1for phenol, respectively.

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

scholarly journals Treatment of effluent from fertilizer industry by adsorption on willow sawdust-removal of Ni(II) and Cd(II) from the effluent

2021 ◽  
pp. 1-12
Author(s):  
Raafia Najam ◽  
Syed Muzaffar Ali Andrabi
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
The World ◽  
Pseudo Second Order ◽  
Almost All ◽  
Willow Tree

Sawdust of willow has been investigated as an adsorbent for the removal of Ni(II), and Cd(II) ions from aqueous solution. Since willow tree is widely grown in almost all parts of Kashmir, it can be a common most easily available, sustainable, low cost adsorbent for the treatment of wastewaters in this part of the world where growing industrialization is affecting water quality like elsewhere in the world. Therefore, it is worthwhile to investigate the potential of sawdust of willow tree as an adsorbent for the removal of Ni(II) and Cd(II) ions from aqueous solution as a first step. Batch experiments were conducted to study the effect of some parameters such as contact time, initial concentration of metal ions, solution pH and temperature. Langmuir and Freundlich models were employed for the mechanistic analysis of experimental data obtained. Results reveal that in our system adsorption follows the Langmuir isotherm. The maximum adsorption capacity of Ni(II) and Cd(II) were found to be 7.98 and 7.11 mg/g respectively at optimum conditions. The pseudo-first-order and pseudo-second-order models were employed for kinetic analysis of adsorption process. The adsorption process follows pseudo-second-order kinetics. The efficacy of the adsorbent in the treatment of effluent from fertilizer factory has been investigated and the results have been found encouraging.

Sugar beet pulp as biomass

2017 ◽  
pp. 29-32 ◽  
Author(s):  
Kazm Eber Özba ◽  
Özen Özboy Özba
Keyword(s):  
Sugar Beet ◽  
Animal Feed ◽  
Sugar Industry ◽  
Low Cost ◽  
Industrial Applications ◽  
Single Cell Protein ◽  
Sugar Beet Pulp ◽  
Raw Material ◽  
Cell Protein ◽  
Beet Pulp

The sugar beet industry produces considerable amounts of organic waste and by-products. Sugar beet pulp (SBP) is the residue that remains after sugar extraction. SBP is a lignocellulosic by-product of the sugar industry and generally used as animal feed at relatively low price. Instead of cattle feeding, SBP can be used as a raw material for industrial applications because it is low-cost and available in large amounts. Biomass is a clean and renewable energy source. The use of SBP for the production of ethanol, methanol, single cell protein, biofuels etc. is economically very attractive. This literature review evaluates the use of SBP as biomass.

Comparative studies on adsorptive removal of heavy metal ions by biosorbent, bio-char and activated carbon obtained from low cost agro-residue

2015 ◽  
Vol 73 (2) ◽  
pp. 423-436 ◽  
Author(s):  
Çisem Kırbıyık ◽  
Ayşe Eren Pütün ◽  
Ersan Pütün
Keyword(s):  
Activated Carbon ◽  
Metal Ion ◽  
Low Cost ◽  
Chemical Activation ◽  
Second Order ◽  
Isotherm Models ◽  
Standard Entropy ◽  
Order Kinetic ◽  
Solution Ph ◽  
Pseudo Second Order

In this study, Fe(III) and Cr(III) metal ion adsorption processes were carried out with three adsorbents in batch experiments and their adsorption performance was compared. These adsorbents were sesame stalk without pretreatment, bio-char derived from thermal decomposition of biomass, and activated carbon which was obtained from chemical activation of biomass. Scanning electron microscopy and Fourier transform–infrared techniques were used for characterization of adsorbents. The optimum conditions for the adsorption process were obtained by observing the influences of solution pH, adsorbent dosage, initial solution concentration, contact time and temperature. The optimum adsorption efficiencies were determined at pH 2.8 and pH 4.0 for Fe(III) and Cr(III) metal ion solutions, respectively. The experimental data were modelled by different isotherm models and the equilibriums were well described by the Langmuir adsorption isotherm model. The pseudo-first-order, pseudo-second-order kinetic, intra-particle diffusion and Elovich models were applied to analyze the kinetic data and to evaluate rate constants. The pseudo-second-order kinetic model gave a better fit than the others. The thermodynamic parameters, such as Gibbs free energy change ΔG°, standard enthalpy change ΔH° and standard entropy change ΔS° were evaluated. The thermodynamic study showed the adsorption was a spontaneous endothermic process.

scholarly journals Adsorption of Cu(II) by Poly-γ-glutamate/Apatite Nanoparticles

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 962
Author(s):  
Kuo-Yu Chen ◽  
Wei-Yu Zeng
Keyword(s):  
Adsorption Capacity ◽  
Kinetic Studies ◽  
Maximum Adsorption Capacity ◽  
Gravimetric Analysis ◽  
Solution Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Initial Adsorption ◽  
Adsorption Equilibrium Data

Poly-γ-glutamate/apatite (PGA-AP) nanoparticles were prepared by chemical coprecipitation method in the presence of various concentrations of poly-γ-glutamate (γ-PGA). Powder X-ray diffraction pattern and energy-dispersive spectroscopy revealed that the main crystal phase of PGA-AP was hydroxyapatite. The immobilization of γ-PGA on PGA-AP was confirmed by Fourier transform infrared spectroscopy and the relative amount of γ-PGA incorporation into PGA-AP was determined by thermal gravimetric analysis. Dynamic light scattering measurements indicated that the particle size of PGA-AP nanoparticles increased remarkably with the decrease of γ-PGA content. The adsorption of aqueous Cu(II) onto the PGA-AP nanoparticles was investigated in batch experiments with varying contact time, solution pH and temperature. Results illustrated that the adsorption of Cu(II) was very rapid during the initial adsorption period. The adsorption capacity of PGA-AP nanoparticles for Cu(II) was increased with the increase in the γ-PGA content, solution pH and temperature. At a pH of 6 and 60 °C, a higher equilibrium adsorption capacity of about 74.80 mg/g was obtained. The kinetic studies indicated that Cu(II) adsorption onto PGA-AP nanoparticles obeyed well the pseudo-second order model. The Langmuir isotherm model was fitted well to the adsorption equilibrium data. The results indicated that the adsorption behavior of PGA-AP nanoparticles for Cu(II) was mainly a monolayer chemical adsorption process. The maximum adsorption capacity of PGA-AP nanoparticles was estimated to be 78.99 mg/g.

scholarly journals Sorption of Pb(II) and Cu(II) by low-cost magnetic eggshells-Fe3O4 powder

2012 ◽  
Vol 18 (2) ◽  
pp. 221-231 ◽  
Author(s):  
Jianwei Ren ◽  
Mokgadi Bopape ◽  
Katlego Setshedi ◽  
Jacob Kitinya ◽  
Maurice Onyango
Keyword(s):  
Metal Ions ◽  
Ph Value ◽  
Low Cost ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Freundlich Adsorption Isotherm ◽  
Equilibrium Data ◽  
Order Kinetic Model ◽  
Media Interaction

This study explored the feasibility of using magnetic eggshell-Fe3O4 powder as adsorbent for the removal of Pb(II) and Cu(II) ions from aqueous solution. The metal ionsadsorption media interaction was characterized using XRD and FTIR. The effects of contact time, initial concentrations, temperature, solution pH and reusability of the adsorption media were investigated. The metal ions adsorption was fast and the amount of metal ions adsorbed increased with an increase in temperature, suggesting an endothermic adsorption. The kinetic data showed that the adsorption process followed the pseudo-second-order kinetic model. The optimal adsorption pH value was around 5.5 at which condition the equilibrium capacity was 263.2 mg/g for Pb(II) and 250.0 for Cu(II). The adsorption equilibrium data fitted very well to the Langmuir and Freundlich adsorption isotherm models. The thermodynamics of Pb(II) and Cu(II) adsorption onto the magnetic eggshell-Fe3O4 powder indicated that the adsorption was spontaneous. The reusability study has proven that magnetic eggshell-Fe3O4 powder can be employed as a low-cost and easy to separate adsorbent.

Sign in / Sign up

Export Citation Format

Share Document