scholarly journals Pressure gain combustion advantage in land-based electric power generation

2017 ◽  
Vol 1 ◽  
pp. K4MD26 ◽  
Author(s):  
Seyfettin C. Gülen
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Heavy Duty ◽  
Quantum Leap ◽  
Pressure Gain Combustion ◽  
Industrial Gas Turbines ◽  
Plant Efficiency

AbstractThis article evaluates the improvement in gas turbine combined cycle power plant efficiency and output via pressure gain combustion (PGC). Ideal and real cycle calculations are provided for a rigorous assessment of PGC variants (e.g., detonation and deflagration) in a realistic power plant framework with advanced heavy-duty industrial gas turbines. It is shown that PGC is the single-most potent knob available to the designers for a quantum leap in combined cycle performance.

scholarly journals Large Heavy-Duty Gas Turbines for Base-Load Power Generation and Heat Cogeneration

1985 ◽  
Author(s):  
John S. Joyce
Keyword(s):  
Power Generation ◽  
Gas Turbines ◽  
High Reliability ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Heavy Duty ◽  
Continuous Service ◽  
Industrial Gas Turbines ◽  
Bulk Power ◽  
Base Load

The predominant role of large gas turbines has shifted from peaking-load duty to midrange and base-load electric power generation, especially within combined-cycle plants. Such applications require heavy-duty industrial gas turbines to ensure the same high reliability and availability for continuous service as the associated steam turbines. It is also important that the gas turbines be designed for low maintenance to minimize the necessary outage times and costs for component repair and replacement. The basic design principles and applications of Model V94 gas turbines are discussed with special reference to highly reliable and economic bulk power generation.

300 MW Combined-Cycle Plant With Integrated Coal Gasification

1984 ◽  
Author(s):  
Rolf H. Kehlhofer
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Gas Turbines ◽  
Power Plants ◽  
Coal Gasification ◽  
District Heating ◽  
Combined Cycle ◽  
Liquid Fuels ◽  
Combined Cycle Plant ◽  
The Individual

In the past 15 years the combined-cycle (gas/steam turbine) power plant has come into its own in the power generation market. Today, approximately 30 000 MW of power are already installed or being built as combined-cycle units. Combined-cycle plants are therefore a proven technology, showing not only impressive thermal efficiency ratings of up to 50 percent in theory, but also proving them in practice and everyday operation (1) (2). Combined-cycle installations can be used for many purposes. They range from power plants for power generation only, to cogeneration plants for district heating or combined cycles with maximum additional firing (3). The main obstacle to further expansion of the combined cycle principle is its lack of fuel flexibility. To this day, gas turbines are still limited to gaseous or liquid fuels. This paper shows a viable way to add a cheap solid fuel, coal, to the list. The plant system in question is a 2 × 150 MW combined-cycle plant of BBC Brown Boveri with integrated coal gasification plant of British Gas/Lurgi. The main point of interest is that all the individual components of the power plant described in this paper have proven their worth commercially. It is therefore not a pilot plant but a viable commercial proposition.

Requirements for Gas Turbine Inlet Systems in Russia

2009 ◽  
Author(s):  
Tagir R. Nigmatulin ◽  
Vladimir E. Mikhailov
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Oil And Gas ◽  
Inlet System ◽  
Climate Zones ◽  
Russian Market ◽  
Turbine Inlet ◽  
Industrial Gas Turbines

Russian power generation, oil and gas businesses are rapidly growing. Installation of new industrial gas turbines is booming to fulfill the demand from economic growth. Russia is a unique country from the annual temperature variation point of view. Some regions may reach up to 100C. One of the biggest challenges for world producers of gas turbines in Russia is the ability to operate products at power plants during cold winters, when ambient temperature might be −60C for a couple of weeks in a row. The reliability and availability of the equipment during the cold season is very critical. Design of inlet systems and filter houses for the Russian market, specifically for northern regions, has a lot of specifics and engineering challenges. Joint Stock Company CKTI is the biggest Russian supplier of air intake systems for industrial gas turbines and axial-flow compressors. In 1969 this enterprise designed and installed the first inlet for the power plant Dagskaya GRES (State Regional Electric Power Plant) with the first 100MW gas-turbine which was designed and manufactured by LMZ. Since the late 1960s CKTI has designed and manufactured inlet systems for the world market and been the main supplier for the Russian market. During the last two years CKTI has designed inlet systems for a broad variety of gas turbine engines ranging from 24MW up to 110MW turbines which are used for power generation and as a mechanical drive for the oil and gas industry. CKTI inlet systems with filtering devices or houses are successfully used in different climate zones including the world’s coldest city Yakutsk and hot Nigeria. CKTI has established CTQs (Critical to quality) and requirements for industrial gas turbine inlet systems which will be installed in Russia in different climate zones for all types of energy installations. The last NPI project of the inlet system, including a nonstandard layout, was done for a small gas-turbine engine which is installed on a railway cart. This arrangement is designed to clean railway lines with the exhaust jet in a quarry during the winter. The design of the inlet system with efficient multistage compressor extraction for deicing, dust and snow resistance has an interesting solution. The detailed description of challenges, weather requirements, calculations, losses, and design methodologies to qualify the system for tough requirements, are described in the paper.

7H™ Combustion System Performance With Fuel Moisturization

2006 ◽  
Author(s):  
Markus Feigl ◽  
Geoff Myers ◽  
Stephen R. Thomas ◽  
Raub Smith
Keyword(s):  
Gas Turbines ◽  
Combined Cycle ◽  
Combustion System ◽  
Heavy Duty ◽  
Single Digit ◽  
Efficiency Performance ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
Cycle Efficiency ◽  
Full Pressure

This paper describes the concept and benefits of the fuel moisturization system for the GE H System™ steam-cooled industrial gas turbine. The DLN2.5H combustion system and fuel moisturization system are both described, along with the influence of fuel moisture on combustor performance as measured during full-scale, full-pressure rig testing of the DLN2.5H combustion system. The lean, premixed DLN2.5H combustion system was targeted to deliver single-digit NOx and CO emissions from 40% to 100% combined cycle load in both the Frame 7H (60 Hz) and Frame 9H (50 Hz) heavy-duty industrial gas turbines. These machines are also designed to yield a potential combined-cycle efficiency of 60 percent or higher. Fuel moisturization contributes to the attainment of both the NOx and the combined-cycle efficiency performance goals, as discussed in this paper.

Dry, Low Emissions for the ‘H’ Heavy-Duty Industrial Gas Turbines: Full-Scale Combustion System Rig Test Results

2003 ◽  
Author(s):  
Geoff Myers ◽  
Dan Tegel ◽  
Markus Feigl ◽  
Fred Setzer ◽  
William Bechtel ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Full Scale ◽  
Combustion System ◽  
Heavy Duty ◽  
Test Program ◽  
Industrial Gas Turbines ◽  
Inlet Conditions

The lean, premixed DLN2.5H combustion system was designed to deliver low NOx emissions from 50% to 100% load in both the Frame 7H (60 Hz) and Frame 9H (50 Hz) heavy-duty industrial gas turbines. The H machines employ steam cooling in the gas turbine, a 23:1 pressure ratio, and are fired at 1440 C (2600 F) to deliver over-all thermal efficiency for the combined-cycle system near 60%. The DLN2.5H combustor is a modular can-type design, with 14 identical chambers used on the 9H machine, and 12 used on the smaller 7H. On a 9H combined-cycle power plant, both the gas turbine and steam turbine are fired using the 14-chamber DLN2.5H combustion system. An extensive full-scale, full-pressure rig test program developed the fuel-staged dry, low emissions combustion system over a period of more than five years. Rig testing required test stand inlet conditions of over 50 kg/s at 500 C and 28 bar, while firing at up to 1440 C, to simulate combustor operation at base load. The combustion test rig simulated gas path geometry from the discharge of the annular tri-passage diffuser through the can-type combustion liner and transition piece, to the inlet of the first stage turbine nozzle. The present paper describes the combustion system, and reports emissions performance and operability results over the gas turbine load and ambient temperature operating range, as measured during the rig test program.

scholarly journals HYBRID ELECTRIC POWERTRAIN FOR LONG-HAUL TRUCKS AND BUSES: PRELIMINARY ANALYSIS OF A NEW CONCEPT BASED ON A COMBINED CYCLE POWER PLANT

2020 ◽  
Vol 4 ◽  
pp. 63-79
Author(s):  
Sebastian Bahamonde Noriega ◽  
Carlo De Servi ◽  
Piero Colonna
Keyword(s):  
Power Plant ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Power Demand ◽  
Prime Mover ◽  
Heavy Duty ◽  
Peak Efficiency ◽  
Hybrid Powertrain ◽  
Cycle System ◽  
Hybrid Electric

The electric hybridization of heavy-duty road vehicles is a promising alternative to reduce the environmental impact of freight and passengers transportation. Employing a micro gas turbine as a prime mover offers several advantages: high power density, fuel flexibility, ultra-low emissions, low vibrations and noise, simplicity and lower maintenance cost. State-of-the-art micro gas turbines feature an efficiency of 30%, which can be increased to 40% by employing a mini organic Rankine cycle system as a bottoming power plant. Such a powertrain could achieve higher efficiency with next-gen micro gas turbines and mini ORC systems, especially with an R&D push of the automotive sector. This paper presents the analysis of a hybrid electric heavy-duty vehicle with a prime mover based on this concept. The best combined cycle system stemming from the design exercise features an estimated peak efficiency of 44%, and a nominal power output of about 150kW. This corresponds to the power demand at cruise condition of a long-haul truck. A series configuration with Lithium-Ion batteries was selected for the hybrid powertrain, for it decouples the prime mover dynamics from the power demand. The benchmark is a vehicle featuring a next generation diesel engine, with a peak efficiency equal to 50%. The results show that the fuel economy can be largely improved by increasing the size of the battery in the hybrid powertrain. Furthermore, employing natural gas in the prime mover of the hybrid vehicle leads to ultra low emissions that are well below the limits set by European and north American regulations. Additionally, the CO2 emissions of the hybrid powertrain are considerably lower than that of the benchmark. The work documented here thus demonstrates the potential of this hybrid powertrain concept, especially in terms of exhaust emissions, as a promising transition technology towards the full electrification of the powertrain.

Comparative Analysis of Off-Design Performance Characteristics of Single and Two Shaft Industrial Gas Turbines

2002 ◽  
Author(s):  
J. H. Kim ◽  
T. S. Kim ◽  
J. L. Sohn ◽  
S. T. Ro
Keyword(s):  
Gas Turbines ◽  
Combined Cycle ◽  
Performance Characteristics ◽  
Cycle Performance ◽  
Operating Characteristics ◽  
Exhaust Temperature ◽  
Operating Modes ◽  
Recovery Capacity ◽  
Industrial Gas Turbines ◽  
Component Models

Off-design steady performance and operating characteristics of single and two shaft gas turbines for electric power generation have been investigated comparatively. A set of balance equations has been derived based on validated component models. A simultaneous calculation scheme has been employed, which is flexible to various engine configurations. Part-load performance analyses of two commercial gas turbines have been carried out to compare operating characteristics between single and two shaft engines. The predicted performance characteristics of both engines coincide soundly with the manufacturer’s data and also correspond with the inherent characteristics of each configuration. The adoption of the VIGV modulation has been addressed in order to examine the possibility of leveling up the heat recovery capacity by maintaining a high turbine exhaust temperature (TET) when those gas turbines are used for combined cycle plants. Maintaining TET at its design value as far as the VIGV modulation allows has been simulated and it has been determined that the TET control is possible at up to 40% and 50% load in the single and two shaft engine, respectively. Combined cycle performances have also been investigated for two engine configurations in different operating modes. While the VIGV modulation produces a favorable influence over the combined cycle performance of the single shaft configuration, the two shaft engine does not appear to be effectively improved by the VIGV modulation since the degradation of gas turbine performance counteracts the advantage of the higher performance of the bottoming (steam turbine) cycle.

Flexible Combined Cycle Gas Turbine Power Plant Utilising Organic Rankine Cycle Technology

2016 ◽  
Author(s):  
Michael Welch ◽  
Nicola Rossetti
Keyword(s):  
Power Generation ◽  
Power Plant ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Combined Cycle ◽  
Exhaust Gas ◽  
Operational Flexibility

Historically gas turbine power plants have become more efficient and reduced the installed cost/MW by developing larger gas turbines and installing them in combined cycle configuration with a steam turbine. These large gas turbines have been designed to maintain high exhaust gas temperatures to maximise the power generation from the steam turbine and achieve the highest overall electrical efficiencies possible. However, in today’s electricity market, with more emphasis on decentralised power generation, especially in emerging nations, and increasing penetration of intermittent renewable power generation, this solution may not be flexible enough to meet operator demands. An alternative solution to using one or two large gas turbines in a large central combined cycle power plant is to design and install multiple smaller decentralised power plant, based on multiple gas turbines with individual outputs below 100MW, to provide the operational flexibility required and enable this smaller power plant to maintain a high efficiency and low emissions profile over a wide load range. This option helps maintain security of power supplies, as well as providing enhanced operational flexibility through the ability to turn turbines on and off as necessary to match the load demand. The smaller gas turbines though tend not to have been optimised for combined cycle operation, and their exhaust gas temperatures may not be sufficiently high, especially under part load conditions, to generate steam at the conditions needed to achieve a high overall electrical efficiency. ORC technology, thanks to the use of specific organic working fluids, permits efficient exploitation of low temperatures exhaust gas streams, as could be the case for smaller gas turbines, especially when working on poor quality fuels. This paper looks at how a decentralised power plant could be designed using Organic Rankine Cycle (ORC) in place of the conventional steam Rankine Cycle to maximise power generation efficiency and flexibility, while still offering a highly competitive installed cost. Combined cycle power generation utilising ORC technology offers a solution that also has environmental benefits in a water-constrained World. The paper also investigates the differences in plant performance for ORC designs utilising direct heating of the ORC working fluid compared to those using an intermediate thermal oil heating loop, and looks at the challenges involved in connecting multiple gas turbines to a single ORC turbo-generator to keep installed costs to a minimum.

Introducing the 1S.W501G Single-Shaft Combined-Cycle Reference Power Plant

2004 ◽  
Author(s):  
Christian Engelbert ◽  
Joseph J. Fadok ◽  
Robert A. Fuller ◽  
Bernd Lueneburg
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Future Market ◽  
Combined Cycle Power Plant ◽  
Highly Efficient ◽  
Fast Start ◽  
Plant Efficiency

Driven by the requirements of the US electric power market, the suppliers of power plants are challenged to reconcile both plant efficiency and operating flexibility. It is also anticipated that the future market will require more power plants with increased power density by means of a single gas turbine based combined-cycle plant. Paramount for plant efficiency is a highly efficient gas turbine and a state-of-the-art bottoming cycle, which are well harmonized. Also, operating and dispatch flexibility requires a bottoming cycle that has fast start, shutdown and cycling capabilities to support daily start and stop cycles. In order to meet these requirements the author’s company is responding with the development of the single-shaft 1S.W501G combined-cycle power plant. This nominal 400MW class plant will be equipped with the highly efficient W501G gas turbine, hydrogen-cooled generator, single side exhausting KN steam turbine and a Benson™ once-through heat recovery steam generator (Benson™-OT HRSG). The single-shaft 1S.W501G design will allow the plant not only to be operated economically during periods of high demand, but also to compete in the traditional “one-hour-forward” trading market that is served today only by simple-cycle gas turbines. By designing the plant with fast-start capability, start-up emissions, fuel and water consumption will be dramatically reduced. This Reference Power Plant (RPP) therefore represents a logical step in the evolution of combined-cycle power plant designs. It combines both the experiences of the well-known 50Hz single-shaft 1S.V94.3A plant with the fast start plant features developed for the 2.W501F multi-shaft RPP. The paper will address results of the single-shaft 1S.W501G development program within the authors’ company.

Operating Experience in Refinery Application of the 13MW-Class Heavy Duty MF-111 Gas Turbine Engine

1990 ◽  
Author(s):  
J. Masada ◽  
I. Fukue
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Experience ◽  
Combined Cycle ◽  
Outlet Temperature ◽  
Heavy Duty ◽  
Turbine Engine ◽  
Industrial Gas Turbines ◽  
Heavy Duty Gas Turbine ◽  
Temperature Levels

A new, 13MW class, heavy duty gas turbine, the “MF-111” was developed for use as a prime mover for cogeneration, combined cycle and repowering applications. The use of such equipment in refineries presents special challenges as regards the combustion of nonstandard fuels, tolerance of industrial environments, and accomodation of site-specific design requirements. Such circumstances add substantially to the tasks of proving and adjusting the design of a new gas turbine, meeting stringent emissions requirements and introducing to the world of industrial gas turbines the benefits of F-class (1250°C burner outlet temperature) levels of thermodynamic performance. This paper describes how these challenges have successfully been met during the three calendar years and ten machine-years of MF-111 refinery-application experience accumulated to-late.

Sign in / Sign up

Export Citation Format

Share Document