scholarly journals Morphology of NdFeB-Type Permanent Magnet Coercivity Enhancement by Heat Treatment Process

2020 ◽  
Author(s):  
Eva Afrilinda ◽  
Dagus Resmana Djuanda ◽  
Shinta Virdhian ◽  
Martin Doloksaribu ◽  
Moch Iqbal Zaelana Muttahar ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Boundaries ◽  
Permanent Magnet ◽  
Heat Treatment Temperature ◽  
Substantial Reduction ◽  
Xrd Analysis ◽  
Treatment Temperature ◽  
X Ray ◽  
High Temperature Heat Treatment ◽  
Fe Content

To understand the morphology of the coercivity enhancement by heat treatment, a commercial sintered NdFeB-type permanent magnet is annealed, and the coercivity is measured by Permagraph. It is shown that the coercivity is increased compared to the initial. Observation by X-Ray Diffraction (XRD) analysis and Scanning Electron Microscope-Energy Dispersive X-ray Spectroscopy (SEM-EDS) is then conducted. The XRD result shows the amount of NdFeB content in the NdFeB-type permanent magnet is increased after heat treatment. The more significant amount of NdFeB content causes higher coercivity. The maximum coercivity, 19 kOe, is achieved at 850 °C of heat treatment temperature, where the NdFeB content is at the highest amount. Microstructural characterizations using SEM-EDS show that at 850 °C of heat treatment temperature, the iron (Fe) content in the grain boundaries is the lowest. It causes higher coercivity. This is due to the magnetically decoupled between NdFeB grains. The decoupling magnet of the NdFeB grains is affected by the Fe content in the grain boundaries. High-temperature heat treatment at 900 and 1050 °C led to the decomposition of NdFeB content in the grains and increased the Fe content in the grain boundaries, which resulted in a substantial reduction of magnetic coercivity.

Preparation and Catalytic Performance of Ti(SO4)2/γ-Al2O3 Catalysts for Oligomerization of 1-Butene

2013 ◽  
Vol 634-638 ◽  
pp. 696-700
Author(s):  
Lin Jiu Xiao ◽  
Peng Li ◽  
Yong Gang Sheng
Keyword(s):  
Heat Treatment ◽  
Physicochemical Properties ◽  
Heat Treatment Temperature ◽  
Catalytic Performance ◽  
Treatment Temperature ◽  
Impregnation Method ◽  
X Ray Diffraction ◽  
Isothermal Adsorption ◽  
X Ray ◽  
Adsorption Desorption

A series of Ti(SO4)2/γ-Al2O3 catalysts were prepared by impregnation method and the catalytic performance of these catalysts in 1-butene oligomerization was investigated. The heat treatment temperature played great influences on the catalytic performance of these catalysts in the oligomerization. 90.1 wt.% conversion of 1-butene and 92.2 wt.% selectivity of dimers were obtained on Ti(SO4)2/γ-Al2O3(450) catalyst at 80 °C, 1.0 Mpa and LHSV=0.6 h−1. The heat treatment temperature determined the crystallinity of TiOSO4 and specific surface area of these catalysts, which affected the catalytic performance of these catalysts in 1-butene oligomerization. In addition, the physicochemical properties of these catalysts were comparatively characterized by powder X-ray diffraction (XRD), N2 isothermal adsorption-desorption techniques.

Phase Separation in Alumina-Chromia

2002 ◽  
Vol 731 ◽  
Author(s):  
M. S. McIntosh ◽  
T. H. Sanders ◽  
J. M. Hampikian
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Miscibility Gap ◽  
Mole Percent ◽  
Tem Analysis ◽  
X Ray ◽  
Heat Treated ◽  
Solution Models ◽  
Liquid And Solid Phases

AbstractThe alumina-chromia system shows complete mutual solubility and is represented by an isomorphous phase diagram. However, the alumina-chromia system exhibits an asymmetric miscibility gap under 1300°C. Using existing data from the literature, the alumina-chromia system was assessed using thermodynamic modeling by Kim and Sanders [1]. Regular and subregular solution models for the liquid and solid phases were used to define the phase boundaries for the miscibility gap in this system. Using this thermodynamic representation of the miscibility gap to select temperatures of interest, 75 mole percent Al2O3samples were synthesized via combustion of powders, followed by pressing into pellets and heat-treated for various times and temperatures. Both X-ray and TEM analysis showed evidence of spinodal decomposition after heat-treatment. X-ray analysis showed that decreasing the heat-treatment temperature increases the compositional difference between the phases present. The experimentally observed microstructures exhibit lamella-like structures that vary in spacing from 8nm to 3nm as the heat-treatment temperature varies from 400°C to 800°C.

Characterization of Zirconia Sizing Nozzle Modifying Addictives Preparated by Sol-Gel Method

2014 ◽  
Vol 1078 ◽  
pp. 31-35
Author(s):  
Liang Zhao ◽  
Qun Hu Xue ◽  
Dong Hai Ding
Keyword(s):  
Heat Treatment ◽  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Heat Treatment Temperature ◽  
Sol Gel ◽  
Treatment Temperature ◽  
Composite Powders ◽  
Gel Method ◽  
X Ray

MgO-Al2O3-ZrO2composite powders with 3 kinds of mass ratio were synthesized by sol–gel method using MgCl2·6H2O, AlCl3·6H2O and ZrOCl2·8H2O as starting materials, and NH3·H2O as a precipitant. The composite powders which match with zirconium oxide particle size and evenly distribute can are advantageous to the formation of metastable t-ZrO2and restrain the grain growth as the additive of modified sizing nozzle. Chemical composition, mineral phase, particle size distribution and micro-morphology of the composite powders were investigated by X-ray fluorescence instrument, X-ray diffractometer, laser particle size analyzer and scanning electron microscope. Research showed that under the process that the concentration of MgCl2solution 0.2 mol/L, AlCl3and ZrOCl2solution concentration 0.5 mol/L, the pH controlled between 10 ~ 11, PEG as the surfactant, drying at 70°C±5°C, heat treatment temperature at 800°C for 3h, particle size distribution of MgO-Al2O3-ZrO2composite powders were: d10= 1.28 μm, d50= 4.65μm, d90= 11.13μm (MgO 10%); d10= 1.15μm, d50= 5.80μm, d90= 15.13μm (MgO 15%);d10= 1.21μm, d50= 6.59μm, d90= 16.87μm (MgO 20%). With the rising of heat treatment temperature, the crystallization degree of composite powders increased, at 800 °C a small amount of t - ZrO2precipitated, meanwhile MgO and Al2O3are still in the amorphous phase. The MgO-A12O3-ZrO2composite powders under this condition have high reactivity and uniform distribution.

scholarly journals Influence of Different Heat Treatment Temperatures on the Microstructure, Corrosion, and Mechanical Properties Behavior of Fe-Based Amorphous/Nanocrystalline Coatings

Coatings ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 858
Author(s):  
Shenglin Liu ◽  
Yongsheng Zhu ◽  
Xinyue Lai ◽  
Xueping Zheng ◽  
Runnan Jia ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Heat Treatment Temperature ◽  
Annealing Treatment ◽  
Treatment Temperature ◽  
X Ray Diffraction ◽  
Crystalline Phases ◽  
X Ray ◽  
Different Temperatures ◽  
Sprayed Coating

Fe-based amorphous/nanocrystalline coatings with smooth, compact interior structure and low porosity were fabricated via supersonic plasma spraying (SPS). The coatings showed outstanding corrosion resistance in a 3.5% NaCl solution at room temperature. In order to analyze the effect of annealing treatment on the microstructure, corrosion resistance and microhardness, the as-sprayed coating was annealed for 1 h under different temperatures such as 350, 450, 550 and 650 °C, respectively. The results showed that the number of oxides and cracks in the coatings presented an obvious increase with increasing annealing temperature, and the corrosion resistance of the coatings showed an obvious reduction. However, the microhardness of coatings showed an important increase. The microhardness of the coating could reach 1018 HV when the heat treatment temperature reached 650 °C. The X-ray diffraction (XRD) results showed that there appeared a number of crystalline phases in the coating when the heat treatment temperature was at 650 °C. The crystalline phases led to the increase of the microhardness.

The Effect of Heat Treatment on the Microstructure of Electroless Ni–P Coatings

2011 ◽  
Vol 464 ◽  
pp. 474-477
Author(s):  
Yan Hai Cheng ◽  
Zhen Cai Zhu ◽  
Zheng Tong Han
Keyword(s):  
Heat Treatment ◽  
Electroless Plating ◽  
Heat Treatment Temperature ◽  
Theoretical Basis ◽  
Phosphorus Content ◽  
Treatment Temperature ◽  
X Ray ◽  
Wear And Corrosion ◽  
Electroless Ni ◽  
The Relationship

In the paper, different phosphorus content Ni-P coatings was prepared by electroless plating. The microstructural changes of electroless Ni-P coatings on both as-deposited condition and heat treatment were investigated by X-ray diffractometry (XRD). The relationship between microstructure of Ni-P coatings and phosphorus content and heat treatment temperature were discussed. This conclusion provided a good theoretical basis for Ni-P coating using for wear and corrosion resistances in the technology of MEMS.

Glancing Angle X-Ray Analysis of Titanium Copper Compound Formations

1984 ◽  
Vol 40 ◽  
Author(s):  
P. A. Psaras ◽  
D. Gupta
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Rutherford Backscattering Spectrometry ◽  
Treatment Temperature ◽  
Rutherford Backscattering ◽  
Copper Compound ◽  
X Ray ◽  
Spectrometry Analysis ◽  
Glancing Angle ◽  
Ideal Stoichiometry

AbstractTitanium copper compound formations have been studied via Seeman Bohlin x-ray diffractometry and Rutherford backscattering spectrometry. The heat treatment temperature range was 350°C to 475°C and th heat treatment times ranged from 0 to 240 minutes. Tetragonal gamma TiCu formed first at ˜350°C and was sequentially followed by orthorhombic TiCu3 at ˜400°C. From Rutherford backscattering spectrometry analysis it was concluded that the second TiCu3 compound deviated from ideal stoichiometry to a nonstoichiometric Ti0.88Cu3.12 composition

Preparation and Characterization of β-Eucryptite Glass Ceramics

2012 ◽  
Vol 624 ◽  
pp. 134-137 ◽  
Author(s):  
Ping Zhai ◽  
Xiao Feng Duan ◽  
Da Qian Chen ◽  
Chong Hai Wang
Keyword(s):  
Heat Treatment ◽  
Expansion Coefficient ◽  
Heat Treatment Temperature ◽  
Glass Ceramics ◽  
Treatment Temperature ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Solid Reaction ◽  
X Ray

In this paper, β-eucryptite glass ceramics were synthesized by using solid reaction method. Phase constitution, structure and properties of the material were studied by X-ray diffraction (XRD) and differential thermal analysis (DTA). Furthermore, the effects of heat treatment temperature and preservation time on the thermal expansion coefficient were also analyzed. The results showed that the crystallization temperature of β-eucryptite glass ceramics was in the range of 810-860 °C and the content was more than 90%. With the increase of heat treatment temperature, the material expansion coefficient decreased.

Nanoporosity in Ceramics from Polymeric Precursors

1994 ◽  
Vol 346 ◽  
Author(s):  
A.W. Reid ◽  
B. Rand ◽  
R.J.P. Emsley
Keyword(s):  
Heat Treatment ◽  
Pore Volume ◽  
Heat Treatment Temperature ◽  
Gas Adsorption ◽  
Treatment Temperature ◽  
X Ray Diffraction ◽  
Carbon Phase ◽  
Volume Increase ◽  
X Ray ◽  
Adsorption Analysis

ABSTRACTIt is shown that ceramics derived from polycarbosilane polymers may develop an open nanoporous network after heat treatment to a temperatures between 1300 and 1550°C in argon. The resulting SiC-based ceramics were characterised by N2 gas adsorption analysis and X-ray diffraction. The apparent surface area, and pore volume increase with increasing heat treatment temperature, reaching values of 170 m2g-1 and 0.12 cm3-1 respectively. The pore network develops as the SiC crystals grow and as carbon is ejected from the structure. It is thought that the porosity may reside within the carbon phase, but this remains to be confirmed.

Isothermal Oxidation Behavior of Fe-33Ni-18Cr Alloy in Different Heat Treatment Temperature

2020 ◽  
Vol 1010 ◽  
pp. 46-51
Author(s):  
Zahraa Zulnuraini ◽  
Noraziana Parimin
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Heat Treatment Temperature ◽  
Minimum Weight ◽  
Isothermal Oxidation ◽  
Optical Microscope ◽  
Treatment Temperature ◽  
Grain Structure ◽  
X Ray ◽  
Average Grain Size

This research study describes the influence of different heat treatment temperature on isothermal oxidation of Fe-33Ni-18Cr alloy. The Fe-33Ni-18Cr alloy was undergone heat treatment at three different temperatures, namely 1000 °C, 1100 °C and 1200 °C for 3h soaking time followed by water quench to vary the grain size of the alloy. This alloy was ground by using several grit of silicon carbide papers as well as weighed by using analytical balance and measured by using Vernier caliper before oxidation test. The heat-treated Fe-33Ni-18Cr alloy was isothermally oxidized at 800 °C for 150h. The characterization of oxidized samples was carried out using optical microscope, scanning electron microscope equipped with energy dispersive x-ray (SEM-EDX) and x-ray diffraction (XRD). The results showed that, increasing the heat treatment temperature was increased the average grain size. The kinetics of oxidation followed the parabolic rate law which represents diffusion-controlled oxide growth rate. Fine grain structure of 1000 °C sample shows minimum weight gain and lower oxidation rate compared to samples of 1100 °C and 1200 °C that indicated oxide spallation and porous structure. Besides, phase analysis showed that the oxidized sample formed several oxide phases.

Effect of Low-Temperature Heat Treatment on PM2.5 Adsorption Properties of GO Films

NANO ◽  
2019 ◽  
Vol 14 (12) ◽  
pp. 1950151
Author(s):  
Weiwu Zou ◽  
Baoshan Gu ◽  
Shiqing Sun ◽  
Shidong Wang ◽  
Xin Li ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Photoelectron Spectroscopy ◽  
Heat Treatment Temperature ◽  
Removal Rate ◽  
Treatment Temperature ◽  
Air Purification ◽  
Vacuum Heat Treatment ◽  
X Ray ◽  
Composition And Structure ◽  
Atmospheric Heat

To explore the mechanism of GO acting on PM[Formula: see text], a graphene oxide (GO) film was prepared via a spraying method for air purification. The effects of different media, temperature and heat treatment times on the adsorption of PM[Formula: see text] on GO film were investigated. The morphology, composition and structure of GO materials were characterized by scanning electron microscopy (SEM), electron spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), infrared spectroscopy (FT-IR) and Raman spectroscopy. When the vacuum heat-treatment temperature is below 80∘C and the atmospheric heat-treatment temperature is below 100∘C, the air purification performance of the film does not change significantly. With the increase in the vacuum heat-treatment temperature, the removal efficiency of PM[Formula: see text] by GO film decreases gradually from 95% to 83%. At different times, the vacuum heat treatment increases with time, and the film removal rate shows a downward trend. As the heat-treatment temperature and time increase, a certain redox reaction occurs in the GO, and the air purification performance decreases. At a temperature of 120∘C and a time of 8[Formula: see text]h, the removal rate drops to 81.68%. The adsorption of PM[Formula: see text] by GO film mainly relies on the action of oxygen-containing functional groups.

Sign in / Sign up

Export Citation Format

Share Document