scholarly journals Synthesis, Characterization and Catalytic Activity of NiO-CoO-MgO Nano-Composite Catalyst

2019 ◽  
Vol 19 (3) ◽  
pp. 675
Author(s):  
Salih Hadi Kadhim ◽  
Tariq Hussein Mgheer ◽  
Hussein Idrees Ismael ◽  
Khudheyer Jawad Kadem ◽  
Ahmed Saadon Abbas ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Mixed Oxides ◽  
Irradiation Time ◽  
Precipitation Method ◽  
Composite Catalyst ◽  
Celestine Blue ◽  
Force Microscopy ◽  
Atomic Force ◽  
Co Precipitation ◽  
Microscopy Techniques

The ternary NiO-CoO-MgO catalyst in three ratios 20:20:60, 25:25:50, and 30:30:40 for these component oxides respectively, were synthesized by co-precipitation method of their carbonates by addition of a precipitate agent in basic media, and then calcinated these carbonate to obtain of mixed oxides. The prepared catalysts were characterized by using Powder X-Ray Diffraction (PXRD), Fourier Infrared spectroscopy (FT-IR), and Atomic Force Microscopy techniques (AFM) were used for identification of the prepared catalysts. The result showed that the particle size of these catalyst ratios, were in the nano range and the smallest size was 25:25:50. The investigation of catalytic activity of prepared catalysts was done by photo decolorization of Celestine blue B dye from simulated industrial wastewaters in aqueous solution. The decolorization efficiency of dye reached 99.9% after irradiation time for 1 h. Study the effect of different reaction conditions such as the pH of the medium, the weight of semiconductor and temperature of mixture reaction were shown that the maximum degradation was observed in conditions at pH = 4, catalyst dosage = 0.08 g, and temperature = 303 K.

Development of Gelatin/HA Membranes

2008 ◽  
Vol 396-398 ◽  
pp. 421-424
Author(s):  
Luci Cristina de Oliveira Vercik ◽  
A. Vercik ◽  
José Carlos Bressiani
Keyword(s):  
Triple Helix ◽  
Precipitation Method ◽  
Gelatin Matrix ◽  
X Ray ◽  
Barrier Membranes ◽  
Force Microscopy ◽  
Crosslinking Process ◽  
Atomic Force ◽  
Pure Phase ◽  
Co Precipitation

The aim of this work is to develop membranes of gelatin/hydorxyapatite composite for using as mechanical barrier. Membranes with 4% of gelatin and 0.5-3% of hydroxyapatite were studied. The composite was obtained by heterogeneous co-precipitation method. X-ray diffractometry showed the formation of a pure phase of hydroxyapatite with excellent crystallinity. Using atomic force microscopy, the distribution of crystals of hydroxyapatite in the gelatin matrix was observed, with nanoparticles of about 50-100nm in a homogeneous mixture. After crosslinking process with glutaraldehyde at different concentrations (0.5, 1, 1.5 and 2%), a significant decrease of the swelling behavior was observed due to the increase of the amount of triple helix in the samples, which increases their stability in aqueous solution.

Synthesis and Characterization of Layered Double Hydroxides/Nafion Composites for Fuel Cell Application

2006 ◽  
Vol 977 ◽  
Author(s):  
Dharmaraj Raghavan ◽  
Bolnale Abayomi ◽  
Miriam Harewood ◽  
Sheriff Abudu ◽  
Elizabeth Williams ◽  
...  
Keyword(s):  
Thermal Characteristics ◽  
Composite Membranes ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Fuel Cell Application ◽  
Co Precipitation ◽  
Double Hydroxides

AbstractIn this study, magnesium-aluminum (Mg-Al) based LDHs with different Mg2+/Al3+ ratios were prepared by co-precipitation method and modified with perfluorooctane-sulfonic acid tetraethylammonium salt (PFOSA). X-Ray Diffraction (XRD), Atomic Force Microscopy (AFM), Fourier Transfer Infrared spectroscopy (FTIR) and Thermogravimetric Analysis (TGA) were carried out to obtain the structural and thermal characteristics of resulting materials. The organo-modified LDHs have been used in the formulation of Nafion® nanocomposites. Nanocomposite membranes were prepared by casting of LDH/PFOSA nanoparticles dispersed in Nafion® solution. Then, modified LDH/Nafion composite membranes were evaluated for water retention capability at ambient and elevated temperature.

Wrinkling Poly(trimethylene 2,5-Furanoate) Free-standing Films: Nanostructure Formation and Physical Properties

2020 ◽  
Author(s):  
Michelina Soccio ◽  
Nadia Lotti ◽  
Andrea Munari ◽  
Esther Rebollar ◽  
Daniel E Martínez-Tong
Keyword(s):  
Irradiation Time ◽  
Polymer Surface ◽  
Laser Source ◽  
Free Standing ◽  
Force Microscopy ◽  
Nanostructure Formation ◽  
Physicochemical Changes ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements

<p>Nanostructured wrinkles were developed on fully bio-based poly(trimethylene furanoate) (PTF) films by using the technique of Laser Induced Periodic Surface Structures (LIPSS). We investigated the effect of irradiation time on wrinkle formation using an UV pulsed laser source, at a fluence of 8 mJ/cm2. It was found that the pulse range between 600 and 4800 pulses allowed formation of periodic nanometric ripples. The nanostructured surface was studied using a combined macro- and nanoscale approach. We evaluated possible physicochemical changes taking place on the polymer surface after irradiation by infrared spectroscopy, contact angle measurements and atomic force microscopy. The macroscopic physicochemical properties of PTF showed almost no changes after nanostructure formation, differently from the results previously found for the terephthalic counterparts, as poly(ethyleneterephthalate), PET, and poly(trimethyleneterephthalate), PTT. The surface mechanical properties of the nanostructured PTF were found to be improved, as evidenced by nanomechanical force spectroscopy measurements. In particular, an increased Young’s modulus and higher stiffness for the nanostructured sample were measured. <br></p>

scholarly journals Review of time-resolved non-contact electrostatic force microscopy techniques with applications to ionic transport measurements

2019 ◽  
Vol 10 ◽  
pp. 617-633 ◽  
Author(s):  
Aaron Mascaro ◽  
Yoichi Miyahara ◽  
Tyler Enright ◽  
Omur E Dagdeviren ◽  
Peter Grütter
Keyword(s):  
Atomic Force Microscopy ◽  
Electrostatic Force ◽  
Oscillation Period ◽  
Electrostatic Force Microscopy ◽  
Time Varying ◽  
Time Resolved ◽  
Battery Materials ◽  
Force Microscopy ◽  
Atomic Force ◽  
Microscopy Techniques

Recently, there have been a number of variations of electrostatic force microscopy (EFM) that allow for the measurement of time-varying forces arising from phenomena such as ion transport in battery materials or charge separation in photovoltaic systems. These forces reveal information about dynamic processes happening over nanometer length scales due to the nanometer-sized probe tips used in atomic force microscopy. Here, we review in detail several time-resolved EFM techniques based on non-contact atomic force microscopy, elaborating on their specific limitations and challenges. We also introduce a new experimental technique that can resolve time-varying signals well below the oscillation period of the cantilever and compare and contrast it with those previously established.

Microstructure Characterization of Metal Mixed Oxides

MRS Advances ◽  
2017 ◽  
Vol 2 (64) ◽  
pp. 4025-4030 ◽  
Author(s):  
T. Kryshtab ◽  
H. A. Calderon ◽  
A. Kryvko
Keyword(s):  
Mixed Oxides ◽  
Profile Analysis ◽  
Atomic Resolution ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Reconstruction Procedure ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Co Precipitation

ABSTRACTThe microstructure of Ni-Mg-Al mixed oxides obtained by thermal decomposition of hydrotalcite-like compounds synthesized by a co-precipitation method has been studied by using X-ray diffraction (XRD) and atomic resolution transmission electron microscopy (TEM). XRD patterns revealed the formation of NixMg1-xO (x=0÷1), α-Al2O3 and traces of MgAl2O4 and NiAl2O4 phases. The peaks profile analysis indicated a small grain size, microdeformations and partial overlapping of peaks due to phases with different, but similar interplanar spacings. The microdeformations point out the presence of dislocations and the peaks shift associated with the presence of excess vacancies. The use of atomic resolution TEM made it possible to identify the phases, directly observe dislocations and demonstrate the vacancies excess. Atomic resolution TEM is achieved by applying an Exit Wave Reconstruction procedure with 40 low dose images taken at different defocus. The current results suggest that vacancies of metals are predominant in MgO (NiO) crystals and that vacancies of Oxygen are predominant in Al2O3 crystals.

scholarly journals Structural and Morphological Properties of Titanium Aluminum Nitride Coatings Produced by Triode Magnetron Sputtering

2014 ◽  
Vol 10 (20) ◽  
pp. 51-64 ◽  
Author(s):  
D.M. Devia ◽  
E. Restrepo-Parra ◽  
J.M. Velez-Restrepo
Keyword(s):  
Magnetron Sputtering ◽  
Bias Voltage ◽  
Structural Changes ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Atomic Force ◽  
Titanium Aluminum ◽  
Microscopy Techniques ◽  
Titanium Aluminum Nitride

Tix Al1−xN coatings were grown using the triode magnetron sputtering technique varying the bias voltage between -40 V and -150V. The influence of bias voltage on structural and morphological properties was analyzed by means of energy dispersive spectroscopy, x-ray diffraction and atomic force microscopy techniques. As the bias voltage increased, an increase inthe Al atomic percentage was observed competing with Ti and producing structural changes. At low Al concentrations, the film presented a FCC crystalline structure; nevertheless, as Al was increased, the structure pre-sented a mix of FCC and HCP phases. On the other hand, an increase inbias voltage produced a decrease films thickness due to an increase in colli-sions. Moreover, the grain size and roughness were also strongly influencedby bias voltage.

Surface diagnostics for scale analysis

2004 ◽  
Vol 49 (2) ◽  
pp. 183-190 ◽  
Author(s):  
S. Dunn ◽  
S. Impey ◽  
C. Kimpton ◽  
S.A. Parsons ◽  
J. Doyle ◽  
...  
Keyword(s):  
Adhesion Force ◽  
Polymer Materials ◽  
Rapid Screening ◽  
Force Measurements ◽  
Energy Materials ◽  
Force Microscopy ◽  
Atomic Force ◽  
Surface Modified ◽  
Surface Diagnostics ◽  
Microscopy Techniques

Stainless steel, polymethylmethacrylate and polytetrafluoroethylene coupons were analysed for surface topographical and adhesion force characteristics using tapping mode atomic force microscopy and force-distance microscopy techniques. The two polymer materials were surface modified by polishing with silicon carbide papers of known grade. The struvite scaling rate was determined for each coupon and related to the data gained from the surface analysis. The scaling rate correlated well with adhesion force measurements indicating that lower energy materials scale at a lower rate. The techniques outlined in the paper provide a method for the rapid screening of materials in potential scaling applications.

scholarly journals Copper-Containing Mixed Metal Oxides (Al, Fe, Mn) for Application in Three-Way Catalysis

Catalysts ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1344
Author(s):  
Tim Van Everbroeck ◽  
Radu-George Ciocarlan ◽  
Wouter Van Hoey ◽  
Myrjam Mertens ◽  
Pegie Cool
Keyword(s):  
Catalytic Activity ◽  
Spinel Structure ◽  
Mixed Oxides ◽  
High Catalytic Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Catalytic Application ◽  
Mixed Spinel ◽  
Co Precipitation ◽  
Three Way Catalysis

Mixed oxides were synthesized by co-precipitation of a Cu source in combination with Al, Fe or Mn corresponding salts as precursors. The materials were calcined at 600 and 1000 °C in order to crystallize the phases and to mimic the reaction conditions of the catalytic application. At 600 °C a mixed spinel structure was only formed for the combination of Cu and Mn, while at 1000 °C all the materials showed mixed spinel formation. The catalysts were applied in three-way catalysis using a reactor with a gas mixture containing CO, NO and O2. All the materials calcined at 600 °C displayed the remarkable ability to oxidize CO with O2 but also to reduce NO with CO, while the pure oxides such as CuO and MnO2 were not able to. The high catalytic activity at 600 °C was attributed to small supported CuO particles present and imperfections in the spinel structure. Calcination at 1000 °C crystallized the structure further which led to a dramatic loss in catalytic activity, although CuAl2O4 and CuFe2O4 still converted some NO. The materials were characterized by X-ray diffraction (XRD), Raman spectroscopy, H2-Temperatrue Programmed Reduction (H2-TPR), N2-sorption and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX).

Sign in / Sign up

Export Citation Format

Share Document