scholarly journals FUNDAMENTAL PEFORMANCE EVALUATION OF ENERGY DISSIPATION DEVICE CONSISTING OF MULITIPLE LAMINATED RUBBER ASSEBLIES BY MEANS OF CYCLIC LOADING TESTS

2009 ◽  
Vol 65 (1) ◽  
pp. 450-455
Author(s):  
Akira IGARASHI ◽  
Kazuma INOUE ◽  
Fumiko TAYA ◽  
Hirokazu IEMURA ◽  
Masahiko YOSHIDA ◽  
...  
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Loading Tests ◽  
Cyclic Loading Tests

scholarly journals Low-Cyclic Loading Tests of Self-Centering Variable Friction (SCVF) Brace

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Qingguang He ◽  
Yanxia Bai ◽  
Weike Wu ◽  
Yongfeng Du
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Energy Dissipation ◽  
Cyclic Loading ◽  
Variable Friction ◽  
Loading Tests ◽  
Low Cyclic Loading ◽  
Energy Dissipation System ◽  
Cyclic Loading Tests ◽  
Dissipation System

A novel assembled self-centering variable friction (SCVF) brace is proposed which is composed of an energy dissipation system, a self-centering system, and a set of force transmission devices. The hysteretic characteristics and energy dissipation of the SCVF brace with various parameters from low-cyclic loading tests are presented. A finite element model was constructed and tested under simulated examination for comparative analysis. The results indicate that the brace shows an atypical flag-type hysteresis curve. The SCVF brace showed its stable self-centering ability and dissipation energy capacity within the permitted axial deformation under different spring and friction plates. A larger deflection of the friction plate will make the variable friction of this SCVF brace more obvious. A higher friction coefficient will make the energy dissipation capacity of the SCVF brace stronger, but the actual friction coefficient will be lower than the design value after repeated cycles. The results of the fatigue tests showed that the energy dissipation system formed by the ceramic fiber friction blocks and the friction steel plates in the SCVF brace has a certain stability. The finite element simulation results are essentially consistent with the obtained test results, which is conducive to the use of finite element software for calculation and structural analysis in actual engineering design.

Experimental Research on the Influence of the Pile Type and Stirrup on the Seismic Performance of PHC Piles

2012 ◽  
Vol 256-259 ◽  
pp. 2079-2084 ◽  
Author(s):  
Tie Cheng Wang ◽  
An Gao ◽  
Hai Long Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
High Strength ◽  
Loading Tests ◽  
Energy Dissipation Capacity ◽  
Pile Type ◽  
Cyclic Loading Tests ◽  
Reversed Cyclic

The influence of the pile type and the stirrup on the seismic performance was evaluated based on the results of reversed cyclic loading tests on the four prestressed high strength concrete (PHC) piles. It is indicated that the AB-type pile has the better seismic performance than the A-type pile from the results. The bearing capacity does not increase obviously with decreasing of the stirrup spacing and increasing of the stirrup diameter. The degradation of stiffness does not decrease significantly with decreasing of the stirrup spacing and increasing of the stirrup diameter. The energy dissipation capacity is improved with increasing of the stirrup diameter and decreasing of the stirrup spacing.

scholarly journals Experimental Analyses of Mechanical Performance of CFST Column to Assembled Steel H-Beam Connections

2014 ◽  
Vol 8 (1) ◽  
pp. 270-278 ◽  
Author(s):  
Cui Chunyi ◽  
Zhao Jinfeng ◽  
Zhang Yannian ◽  
Zuo Wenxin
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Compression Ratio ◽  
Mechanical Performance ◽  
Axial Compression Ratio ◽  
Ring Plate ◽  
Loading Tests ◽  
Hysteretic Characteristics ◽  
H Beam ◽  
Cyclic Loading Tests

The mechanical performance of a new proposed type of cross-shaped connection with concrete-filled steel tubular (CFST) column and assembled steel H-beam was investigated. Cyclic loading tests on the cross-shaped connections are carried out by using MTS servo loading system. Comparative analyses are conducted based on the experimental results including hysteretic curves, skeleton curves and stiffness degradation curves as well as ductility coefficients of cyclic loading tests. Furthermore, effects of geometric parameters of ring-stiffened plate, axial compression ratio and backing plate on the deformation performance of cross-shaped connections are analyzed. The results show that the increase of width of ring plate and the shape change of ring plate from square to circle can both significantly improve the ductility and the hysteretic characteristics of connection. It is emphasized that the specimen with square ring plates is of better deformation performance but lower bearing capacity than the ones with circular ring plates. Besides, the backing plates always have positive effects on the hysteretic characteristics, ductility and energy dissipation of the CFST column connections. Conversely, the increase of axial compression ratio contributes negatively to both the bearing capacity and deformation performance of the connection specimens. It can be concluded that the presented cross-shaped connection is of good deformation performance relating to hysteretic characteristics, energy dissipation and ductility, which can provide reference towards engineering practice with potential perspective application.

scholarly journals TENSILE AND CYCLIC LOADING TESTS OF HORIZONTAL BRACE USING GLUED LAMINATED TIMBER WITH STEEL INSERTED PLATE

2019 ◽  
Vol 25 (60) ◽  
pp. 655-659
Author(s):  
Shuzo HIROISHI ◽  
Akira OKADA ◽  
Naoya MIYASATO ◽  
Noburu NAKAMURA ◽  
Kenichi MAMURO ◽  
...  
Keyword(s):  
Cyclic Loading ◽  
Glued Laminated Timber ◽  
Loading Tests ◽  
Cyclic Loading Tests
Sign in / Sign up

Export Citation Format

Share Document