Pilot Study Protocol: Cervical Spine Joint Pain and Stiffness - Accuracy of Physical Assessment in Nursing (Preprint)

2021 ◽  
Author(s):  
Bruno Garrido Soares ◽  
Fatima Raquel Fonseca ◽  
Patrícia Fonseca ◽  
Paulo Jorge Alves

BACKGROUND Cervical spine dysfunction (CSD) is a problem with high personal, social and economic impact worldwide. Although its etiology is described as multifactorial, there is a need for better clarification. Literature has shown the relationship between the cervical condition, the mandibular functioning and the visceral condition. In order to guide and contribute to the accuracy of the physical assessment performed by nurses, we decided to study the influence of the stomatognathic system (SS) and viscerosomatic reflexes (VR) on pain and joint stiffness of the cervical spine. OBJECTIVE Describe the pilot study protocol of the influence of SS and RV on cervical structures. METHODS Pilot study, with a quasi-experimental design, carried out in 2019, with 50 volunteer participants from the university population of the Academic Federation of Porto, where the influence of the usual intercuspation change, the occlusal deprogramming and the pressure stimulus of the reflex skin region of the ilium/colon in the cervical spine were analyzed. This study was divided into two moments, where we first performed the kinematic and pain analysis in the passive mobilization of the upper cervical spine, using the Motion Capture System® and the Visual Analog Scale. In the second moment, we evaluated the pain threshold on palpation of the erector neck muscles and the structures of the stomatognathic system, using algometry. The influence of viscerosomatic reflexes on the structures of the stomatognathic system was also analyzed. RESULTS Selection and preparation of the data collection site, acquisition of materials, constitution of the sample group and data collection were completed. The analysis of the results is being carried out. CONCLUSIONS The data from this study will allow the observation of the possible influence of SS and VR on pain and range of motion of the upper cervical spine, providing data for future randomized studies. Potential limitations have been identified.

10.2196/31878 ◽  
2021 ◽  
Author(s):  
Bruno Garrido Soares ◽  
Fatima Raquel Fonseca ◽  
Patrícia Fonseca ◽  
Paulo Jorge Alves

Skull Base ◽  
2008 ◽  
Vol 18 (S 01) ◽  
Author(s):  
Harminder Singh ◽  
Bartosz Grobelny ◽  
Adam Flanders ◽  
Marc Rosen ◽  
Paul Schiffmacher ◽  
...  

2021 ◽  
pp. 1-7
Author(s):  
Marko Jug

<b><i>Introduction:</i></b> In the case of tumor resection in the upper cervical spine, a multilevel laminectomy with instrumented fixation is required to prevent kyphotic deformity and myelopathy. Nevertheless, instrumentation of the cervical spine in children under the age of 8 years is challenging due to anatomical considerations and unavailability of specific instrumentation. <b><i>Case Presentation:</i></b> We present a case of 3D-printed model-assisted cervical spine instrumentation in a 4-year-old child with post-laminectomy kyphotic decompensation of the cervical spine and spinal cord injury 1 year after medulloblastoma metastasis resection in the upper cervical spine. Due to unavailability of specific instrumentation, 3D virtual planning was used to assess and plan posterior cervical fixation. Fixation with 3.5 mm lateral mass and isthmic screws was suggested and the feasibility of fixation was confirmed “in vitro” in a 3D-printed model preoperatively to reduce the possibility of intraoperative implant-spine mismatch. Intraoperative conditions completely resembled the preoperative plan and 3.5 mm polyaxial screws were successfully used as planned. Postoperatively the child made a complete neurological recovery and 2 years after the instrumented fusion is still disease free with no signs of spinal decompensation. <b><i>Discussion/Conclusion:</i></b> Our case shows that posterior cervical fixation with the conventional screw-rod technique in a 4-year-old child is feasible, but we suggest that suitability and positioning of the chosen implants are preoperatively assessed in a printed 3D model. In addition, a printed 3D model offers the possibility to better visualize and sense spinal anatomy “in vivo,” thereby helping screw placement and reducing the chance for intraoperative complications, especially in the absence of intraoperative spinal navigation.


1981 ◽  
Vol 30 (1) ◽  
pp. 41-47
Author(s):  
M. Yamanaka ◽  
G. Awaya ◽  
S. Takata ◽  
N. Nishijima ◽  
S. Shimamura

2015 ◽  
Vol 101 (4) ◽  
pp. 519-522 ◽  
Author(s):  
G. Mirouse ◽  
A. Journe ◽  
L. Casabianca ◽  
P.E. Moreau ◽  
S. Pannier ◽  
...  

2013 ◽  
Vol 53 (9) ◽  
pp. 620-624 ◽  
Author(s):  
Alessandro DI RIENZO ◽  
Maurizio IACOANGELI ◽  
Lorenzo ALVARO ◽  
Roberto COLASANTI ◽  
Elisa MORICONI ◽  
...  

Author(s):  
Shintaro Honda ◽  
Eijiro Onishi ◽  
Takumi Hashimura ◽  
Satoshi Ota ◽  
Satoshi Fujita ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document