scholarly journals Probability, consequences, and mitigation for lightning strikes to Hanford site high-level waste tanks

1996 ◽  
Author(s):  
J.J. Zach
1996 ◽  
Vol 465 ◽  
Author(s):  
M. Mika ◽  
M. J. Schweiger ◽  
J. D. Vienna ◽  
P. Hrma

ABSTRACTThe liquidus temperature (TL) often limits the loading of high-level waste in glass through the constraint that TL must be at least 100°C below the temperature at which the glass viscosity is 5 Pa-s. In this study, values of TL for spinel primary crystalline phase were measured as a function of glass composition. The test glasses were based on high-iron Hanford Site tank wastes. All studied glasses precipitated spinel (Ni,Fe,Mn)(Cr,Fe)2O4 as the primary crystalline phase. TL was increased by additions of Cr2O3, NiO, Al2O3, Fe2O3, MgO, and MnO; while Li2O, Na2O, B2O3, and SiO2 had a negative effect. Empirical mixture models were fitted to data.


1995 ◽  
Author(s):  
P.L. Reeder ◽  
D.C. Stromswold ◽  
R.L. Brodzinski ◽  
J.H. Reeves ◽  
W.E. Wilson

Author(s):  
Robert E. Prince ◽  
Bradley W. Bowan

This paper describes actual experience applying a technology to achieve volume reduction while producing a stable waste form for low and intermediate level liquid (L/ILW) wastes, and the L/ILW fraction produced from pre-processing of high level wastes. The chief process addressed will be vitrification. The joule-heated ceramic melter vitrification process has been used successfully on a number of waste streams produced by the U.S. Department of Energy (DOE). This paper will address lessons learned in achieving dramatic improvements in process throughput, based on actual pilot and full-scale waste processing experience. Since 1991, Duratek, Inc., and its long-term research partner, the Vitreous State Laboratory of The Catholic University of America, have worked to continuously improve joule heated ceramic melter vitrification technology in support of waste stabilization and disposition in the United States. From 1993 to 1998, under contact to the DOE, the team designed, built, and operated a joule-heated melter (the DuraMelterTM) to process liquid mixed (hazardous/low activity) waste material at the Savannah River Site (SRS) in South Carolina. This melter produced 1,000,000 kilograms of vitrified waste, achieving a volume reduction of approximately 70 percent and ultimately producing a waste form that the U.S. Environmental Protection Agency (EPA) delisted for its hazardous classification. The team built upon its SRS M Area experience to produce state-of-the-art melter technology that will be used at the DOE’s Hanford site in Richland, Washington. Since 1998, the DuraMelterTM has been the reference vitrification technology for processing both the high level waste (HLW) and low activity waste (LAW) fractions of liquid HLW waste from the U.S. DOE’s Hanford site. Process innovations have doubled the throughput and enhanced the ability to handle problem constituents in LAW. This paper provides lessons learned from the operation and testing of two facilities that provide the technology for a vitrification system that will be used in the stabilization of the low level fraction of Hanford’s high level tank wastes.


Author(s):  
Gabriela Vazquez ◽  
Tomas Pribanic

There are approximately 56 million gallons (212km3) of high level waste (HLW) at the U.S. Department of Energy (DOE) Hanford Site. It is scheduled that by the year 2040, the HLW is to be completely transferred to secure double-shell tanks (DST) from the leaking single-tanks (SST) via transfer pipeline system. Blockages have formed inside the pipes during transport because of the variety in composition and characteristics of the waste. These full and partial plugs delay waste transfers and require manual intervention to repair, therefore are extremely expensive, consuming millions of dollars and further threatening the environment. To successfully continue the transfer of waste through the pipelines, DOE site engineers are in need of a technology that can accurately locate the blockages and unplug the pipelines. In this study, the proposed solution to remediate blockages formed in pipelines is the use of a peristaltic crawler: a pneumatically/hydraulically operated device that propels itself in a worm-like motion through sequential fluctuations of pressure in its air cavities. The crawler is also equipped with a high-pressure water nozzle used to clear blockages inside the pipelines. The crawler is now in its third generation. Previous generations showed limitations in its durability, speed, and maneuverability. Latest improvements include an automation of sequence that prevents kickback, a front-mounted inspection camera for visual feedback, and a thinner wall outer bellow for improved maneuverability. Different experimental tests were conducted to evaluate the improvements of crawler relative to its predecessors using a pipeline test-bed assembly. Anchor force tests, unplugging tests, and fatigue testing for both the bellow and rubber rims have yet to be conducted and thus results are not presented in this research. Experiments tested bellow force and response, cornering maneuverability, and straight line navigational speed. The design concept and experimental test results are reported.


Sign in / Sign up

Export Citation Format

Share Document