scholarly journals Selenide isotope generator for the Galileo Mission: copper/water axially-grooved heat pipe topical report

1979 ◽  
Author(s):  
N.P. Strazza
Keyword(s):  
Heat Pipe ◽  
Copper Water ◽  
Isotope Generator

scholarly journals Experimental Study on Thermal Performance of a Bent Copper-Water Heat Pipe

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Shuangshuang Miao ◽  
Jiajia Sui ◽  
Yulong Zhang ◽  
Feng Yao ◽  
Xiangdong Liu
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Critical Heat Flux ◽  
Working Conditions ◽  
Thermal Performance ◽  
Heat Input ◽  
High Heat ◽  
High Heat Flux ◽  
Electronic Components ◽  
Copper Water

Vapor-liquid phase change is regarded as an efficient cooling method for high-heat-flux electronic components. The copper-water bent heat pipes are particularly suited to the circumstances of confined space or misplaced heat and cold sources for high-heat-flux electronic components. In this paper, the steady and transient thermal performance of a bent copper-water heat pipe is studied based on a performance test system. The effects of cooling temperature, working conditions on the critical heat flux, and equivalent thermal conductivity have been examined and analyzed. Moreover, the influences of heat input and working conditions on the thermal response of a bent heat pipe have also been discussed. The results indicate that the critical heat flux is enhanced due to the increases in cooling temperature and the lengths of the evaporator and condenser. In addition, the critical heat flux is improved by extending the cooling length only when the operating temperature is higher than 50°C. The improvement on the equivalent thermal by increasing the heating length is more evident than that by increasing cooling length. It is also demonstrated by the experiment that the bent copper-water heat pipe can respond quickly to the variation of heat input and possesses superior transient heat transfer performance.

An Experimental Study of Micro Radially Rotating Heat Pipes With Water as the Working Fluid

2008 ◽  
Author(s):  
Yiding Cao ◽  
Jian Ling
Keyword(s):  
Heat Pipe ◽  
Thermal Conductance ◽  
Heat Pipes ◽  
Working Fluid ◽  
Rotating Speed ◽  
Copper Water ◽  
High Pressure Compressor ◽  
Potential Applications ◽  
Inner Diameter ◽  
Pressure Compressor

In this study, three copper-water rotating heat pipes having inner diameters of 1.5, 2, and 3 mm, respectively, are fabricated and tested. The effectiveness of the copper-water heat pipe is first validated by comparing its performance with that of a copper bar having the same inner and outer diameters. The heat pipes are then tested to prove their reliability, high effective thermal conductance, and critical working limitation. The experimental data shows that the critical limitation may be reached when the inner diameter of the heat pipe is below 1.5 mm under the condition of a low rotating speed. The tests of these water heat pipes could also explore potential applications of radially rotating heat pipes in disks/blades of a high-pressure compressor.

Investigation of a Heat Pipe Array for Convective Cooling

1995 ◽  
Vol 117 (3) ◽  
pp. 208-214 ◽  
Author(s):  
A. H. Howard ◽  
G. P. Peterson
Keyword(s):  
Pressure Drop ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Base Plate ◽  
Heat Pipes ◽  
Plate Temperature ◽  
Maximum Heat ◽  
Heat Rejection ◽  
Convective Cooling ◽  
Copper Water

A combined experimental and analytical investigation was conducted to evaluate a heat pipe convective cooling device consisting of sixteen small copper/water heat pipes mounted vertically in a 4 × 4 array which was 25.4 mm square. The analytical portion of the investigation focused on determination of the maximum heat transport capacity and the resistance of the individual heat pipes. The resistance of each heat pipe was found to be 2.51 K/Watt, or more than 3 times smaller than the resistance produced by a solid copper rod with the same dimensions. The maximum predicted heat rejection for the module was over 50 Watts, or a power density in excess of 7.75 Watts/cm2. In the experimental portion of the investigation, two different modules were tested. The first module utilized ten circular aluminum fins mounted on the condenser end of each heat pipe to enhance heat rejection, while the second contained only the sixteen copper/water heat pipes. The effects of flow velocity, input power, and base plate temperature on the overall thermal resistance and the heat rejection capacity were determined, as well as the pressure drop resulting from each module. The finned heat pipe array was found to have a lower overall thermal resistance and thus, a higher heat rejection capacity, but also resulted in a significantly larger pressure drop than the array without fins. The results of the heat pipe array experiments were also compared with experimental and empirical results obtained from flow over a flat plate 25.4 mm square.

Sign in / Sign up

Export Citation Format

Share Document