scholarly journals Development of a low-cost integrated 20-kW ac solar tracking sub- array for grid-connected PV power system applications. Phase 1, Annual technical report, 11 July 1995--31 July 1996

1997 ◽  
Author(s):  
M. Stern ◽  
R. West ◽  
G. Fourer ◽  
W. Whalen ◽  
M. Van Loo ◽  
...  
1997 ◽  
Author(s):  
M. Stern ◽  
R. West ◽  
G. Fourer ◽  
W. Whalen ◽  
M. Van Loo ◽  
...  
Keyword(s):  
Low Cost ◽  

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 726
Author(s):  
Francisco J. Gómez-Uceda ◽  
José Ramirez-Faz ◽  
Marta Varo-Martinez ◽  
Luis Manuel Fernández-Ahumada

In this work, an omnidirectional sensor that enables identification of the direction of the celestial sphere with maximum solar irradiance is presented. The sensor, based on instantaneous measurements, functions as a position server for dual-axis solar trackers in photovoltaic plants. The proposed device has been developed with free software and hardware, which makes it a pioneering solution because it is open and accessible as well as capable of being improved by the scientific community, thereby contributing to the rapid advancement of technology. In addition, the device includes an algorithm developed ex professo that makes it possible to predetermine the regions of the celestial sphere for which, according to the geometric characteristics of the PV plant, there would be shading between the panels. In this way, solar trackers do not have to locate the Sun’s position at all times according to astronomical models, while taking into account factors such as shadows or cloudiness that also affect levels of incident irradiance on solar collectors. Therefore, with this device, it is possible to provide photovoltaic plants with dual-axis solar tracking with a low-cost device that helps to optimise the trajectory of the trackers and, consequently, their radiative capture and energy production.


2020 ◽  
Vol 15 (4) ◽  
pp. 613-619
Author(s):  
Li Kong ◽  
Yunpeng Zhang ◽  
Zhijian Lin ◽  
Zhongzhu Qiu ◽  
Chunying Li ◽  
...  

Abstract The present work aimed to select the optimum solar tracking mode for parabolic trough concentrating collectors using numerical simulation. The current work involved: (1) the calculation of daily solar radiation on the Earth’s surface, (2) the comparison of annual direct solar radiation received under different tracking modes and (3) the determination of optimum tilt angle for the north-south tilt tracking mode. It was found that the order of solar radiation received in Shanghai under the available tracking modes was: dual-axis tracking > north-south Earth’s axis tracking > north-south tilt tracking (β = 15°) > north-south tilt tracking (β = 45) > north-south horizontal tracking > east-west horizontal tracking. Single-axis solar tracking modes feature simple structures and low cost. This study also found that the solar radiation received under the north-south tilt tracking mode was higher than that of the north-south Earth’s axis tracking mode in 7 out of 12 months. Therefore, the north-south tilt tracking mode was studied separately to determine the corresponding optimum tilt angles in Haikou, Lhasa, Shanghai, Beijing and Hohhot, respectively, which were shown as follows: 18.81°, 27.29°, 28.67°, 36.21° and 37.97°.


Author(s):  
Devina Cristine Marubin ◽  
◽  
Sim Sy Yi ◽  

Can-Sized satellite (canSAT) is a small satellite that is used for educational purpose. CanSAT offer student to build their satellites with their creativity which make the learning process more effective. In Malaysia, SiswaSAT is held by the Malaysia Space Agency for students in different categories to participate and build their satellites according to rules set and it should be a low-cost project. CanSAT can be divided into few parts which are communication system, onboard data acquisition, ground control station and power system. The power system is one of the important and heaviest subsystems, it needed to supply power, but weight and size are one of the main concerned as the canSAT should not exceed the required weight and selecting power supply that is matched with the overall power budget that has small size and lightweight is challenging. Therefore, the power supply selection should consider this detail. The power distribution design should be able to supply an appropriate amount of current and voltage to the components according to their specification. This study aims to develop and test the proposed prototype which is named ScoreSAT able to provide data and have enough power supply for the whole operation. Therefore, an initiative to develop the appropriate power distribution design for canSAT is taken to overcome the problem of the power system. Moreover, each subsystem needs to be tested by obtaining the results from the onboard data acquisition and transmit the data using the communication system before integrating into the power system. ScoreSAT prototype needs to carry the system that is mounted inside, thus the space inside the prototype needs to be fully utilized for the whole system to fit in. ScoreSAT completes the mission by obtaining data acquisition during the operation.


Sign in / Sign up

Export Citation Format

Share Document