scholarly journals Surfactant-enhanced alkaline flooding for light oil recovery. Final report 1994--1995

1995 ◽  
Author(s):  
D.T. Wasan
Keyword(s):  
Oil Recovery ◽  
Final Report ◽  
Light Oil

The Mechanism of Flue Gas Injection for Enhanced Light Oil Recovery

2004 ◽  
Vol 126 (2) ◽  
pp. 119-124 ◽  
Author(s):  
O. S. Shokoya ◽  
S. A. (Raj) Mehta ◽  
R. G. Moore ◽  
B. B. Maini ◽  
M. Pooladi-Darvish ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Flue Gas ◽  
Gas Injection ◽  
Cost Effective ◽  
Air Injection ◽  
Oil Reservoirs ◽  
Flue Gases ◽  
Low Permeability ◽  
Light Oil ◽  
Light Oil Reservoirs

Flue gas injection into light oil reservoirs could be a cost-effective gas displacement method for enhanced oil recovery, especially in low porosity and low permeability reservoirs. The flue gas could be generated in situ as obtained from the spontaneous ignition of oil when air is injected into a high temperature reservoir, or injected directly into the reservoir from some surface source. When operating at high pressures commonly found in deep light oil reservoirs, the flue gas may become miscible or near–miscible with the reservoir oil, thereby displacing it more efficiently than an immiscible gas flood. Some successful high pressure air injection (HPAI) projects have been reported in low permeability and low porosity light oil reservoirs. Spontaneous oil ignition was reported in some of these projects, at least from laboratory experiments; however, the mechanism by which the generated flue gas displaces the oil has not been discussed in clear terms in the literature. An experimental investigation was carried out to study the mechanism by which flue gases displace light oil at a reservoir temperature of 116°C and typical reservoir pressures ranging from 27.63 MPa to 46.06 MPa. The results showed that the flue gases displaced the oil in a forward contacting process resembling a combined vaporizing and condensing multi-contact gas drive mechanism. The flue gases also became near-miscible with the oil at elevated pressures, an indication that high pressure flue gas (or air) injection is a cost-effective process for enhanced recovery of light oils, compared to rich gas or water injection, with the potential of sequestering carbon dioxide, a greenhouse gas.

scholarly journals DEVELOPMENT AND OPTIMIZATION OF GAS-ASSISTED GRAVITY DRAINAGE (GAGD) PROCESS FOR IMPROVED LIGHT OIL RECOVERY

2004 ◽  
Author(s):  
Dandina N. Rao ◽  
Subhash C. Ayirala ◽  
Madhav M. Kulkarni ◽  
Amit P. Sharma
Keyword(s):  
Oil Recovery ◽  
Gravity Drainage ◽  
Light Oil

Multiphase Flow Loop Testing of Autonomous Inflow Control Valve for Light Oil

2021 ◽  
Author(s):  
Soheila Taghavi ◽  
Ismarullizam Mohd Ismail ◽  
Haavard Aakre ◽  
Vidar Mathiesen
Keyword(s):  
Multiphase Flow ◽  
Oil Recovery ◽  
Flow Behavior ◽  
Control Valve ◽  
Flow Loop ◽  
Negative Effects ◽  
Total Recovery ◽  
Light Oil ◽  
Control Devices ◽  
Model Oil

Abstract To increase the production and recovery of marginal, mature, and challenging oil reservoirs, developing new inflow control technologies is of great importance. In cases where production of surrounding reservoir fluids such as gas and water can cause negative effects on both the total oil recovery and the amounts of energy required to drain the reservoir, the multiphase flow performances of these technologies are of particular significance. In typical cases, a Long Horizontal Well (LHW) will eventually start producing increasing amounts of these fluids. This will cause the Water Cut (WC) and/or Gas Oil Ratio (GOR) to rise, ultimately forcing the well to be shut down even though there still are considerable amounts of oil left in the reservoir. In earlier cases, Inflow Control Devices (ICD) and Autonomous Inflow Control Devices (AICD) have proven to limit these challenges and increase the total recovery by balancing the influx along the well and delaying the breakthrough of gas and/or water. The Autonomous Inflow Control Valve (AICV) builds on these same principles, and in addition has the ability to autonomously close when breakthrough of unwanted gas and/or water occurs. This will even out the total drawdown in the well, allowing it to continue producing without the WC and/or GOR reaching inacceptable limits. As part of the qualification program of the light-oil AICV, extensive flow performance tests have been carried out in a multiphase flow loop test rig. The tests have been performed under realistic reservoir conditions with respect to variables such as pressure and temperature, with model oil, water, and gas at different WC's and GOR's. Conducting these multiphase experiments has been valuable in the process of establishing the AICV's multiphase flow behavior, and the results are presented and discussed in this paper. Single phase performance and a comparison with a conventional ICD are also presented. The results display that the AICV shows significantly better performance than the ICD, both for single and multiphase flow. A static reservoir modelling method have been used to evaluate the AICV performance in a light-oil reservoir. When compared to a screen-only completion and an ICD completion, the simulation shows that a completion with AICV's will outperform the above-mentioned completions with respect to WC and GOR behavior. A discussion on how this novel AICV can be utilized in marginal, mature, and other challenging reservoirs will be provided in the paper.

The Features of Microwave Thermal Conversion of Oil Sludge

2012 ◽  
Vol 232 ◽  
pp. 788-791
Author(s):  
Wan Fu Wang ◽  
Guo Li ◽  
Xing Yue Yong ◽  
Peng Liu ◽  
Xiao Fei Zhang
Keyword(s):  
Thermal Treatment ◽  
Oil Recovery ◽  
Rapid Heating ◽  
Thermal Conversion ◽  
Conversion Process ◽  
Oil Sludge ◽  
Microwave Drying ◽  
Microwave Pyrolysis ◽  
Light Oil ◽  
Increased Oil Recovery

The microwave thermal conversion process of oil sludge was studied. It was found that the microwave thermal conversion process of oil sludge consisted of 5 stages: rapid heating, microwave drying, microwave hydrocarbons evaporation, microwave pyrolysis and microwave calcining. Using the residue produced from the microwave thermal treatment of oil sludge as a microwave absorbent can significantly accelerate the conversion. However, it does not show significant effect on the features of microwave thermal conversion. Meanwhile, the addition of residue at appropriate percentages increased oil recovery rate. The non-condensable gases consist of H2 and C1~C5 hydrocarbons. The recovered oil was mainly produced at microwave evaporation and microwave pyrolysis stages, consisting of 89% light oil and 11% heavy oil.

Sign in / Sign up

Export Citation Format

Share Document