scholarly journals Characterization of the matrix of brittle matrix composites

1970 ◽  
Author(s):  
James Frederick Holzgraf
Keyword(s):  
Matrix Composites ◽  
Brittle Matrix ◽  
Brittle Matrix Composites ◽  
The Matrix

Stochastic Aspects of Matrix Cracking in Brittle Matrix Composites

1993 ◽  
Vol 115 (3) ◽  
pp. 314-318 ◽  
Author(s):  
S. M. Spearing ◽  
F. W. Zok
Keyword(s):  
Matrix Cracking ◽  
Matrix Composites ◽  
Brittle Matrix ◽  
Tensile Response ◽  
Brittle Matrix Composites ◽  
Crack Interactions ◽  
The Matrix ◽  
Interface Slip ◽  
Bridging Fibers

A computer simulation of multiple cracking in fiber-reinforced brittle matrix composites has been conducted, with emphasis on the role of the matrix flaw distribution. The simulations incorporate the effect of bridging fibers on the stress required for cracking. Both short and long (steady-state) flaws are considered. Furthermore, the effects of crack interactions (through the overlap of interface slip lengths) are incorporated. The influence of the crack distribution on the tensile response of such composites is also examined.

Improving Fracture Toughness of Brittle Matrix Composites Using End-Shaped Ductile Fibers: The Effects of Adhesion and Matrix Shrinkage

Materials ◽  
2003 ◽  
Author(s):  
Robert C. Wetherhold ◽  
Renee M. Bagwell
Keyword(s):  
Fracture Toughness ◽  
Bond Strength ◽  
Surface Chemistry ◽  
Matrix Composites ◽  
Release Agent ◽  
Brittle Matrix ◽  
Matrix Shrinkage ◽  
Pull Out ◽  
Brittle Matrix Composites ◽  
The Matrix

Ductile fibers are added to brittle matrix composites to increase the fracture toughness. To further improve fracture toughness, end shaped ductile fibers are added to act as anchors to utilize more of the fibers’ plasticity. Previous research focused on optimizing the volume of the shaped end for a given end shape family. Results indicate that for a given end shape family there is an optimum volume; above or below this volume results in a lower fracture toughness contribution. This research investigates two additional factors, adhesion of the matrix to the fiber and matrix shrinkage, and determines their effects on the fracture toughening of brittle matrix composites. The fiber was an annealed copper and the matrices used were a low shrinkage epoxy, a high shrinkage epoxy, and polyester. Results indicate that controlling the surface chemistry of the fiber can give an additional degree of freedom to the utilization of the fiber plasticity, although the importance of this control depends on the particular system. The fiber surface chemistry affects the bond strength and the adhesion; if the fiber cannot debond from the matrix, then shaping the end does not permit use of the plastic potential. Depending on the system, the adhesion and bond strength of the matrix to the fiber significantly affects the amount of fiber plasticity utilized. To determine the effects of friction and matrix shrinkage on the utilization of the fiber plasticity, release agent was applied to the end shaped fibers to reduce the adhesion, bond strength, and friction during pull out. Results indicate that frictional work and adhesion has a large impact on the utilization of the fiber plasticity; with release agent, the end shaped fiber utilizes little of the fiber plasticity. Furthermore, this indicates that for the matrices investigated, matrix shrinkage has a minor influence on the utilization of the fiber plasticity.

Brittle Matrix Composites 8

2006 ◽  
Author(s):  
A.M. Brandt ◽  
V.C. Li ◽  
I.H. Marshall
Keyword(s):  
Matrix Composites ◽  
Brittle Matrix ◽  
Brittle Matrix Composites

Brittle matrix composites 7

2003 ◽  
Author(s):  
A. M. Brandt ◽  
V. C. Li ◽  
I. H. Marshall
Keyword(s):  
Matrix Composites ◽  
Brittle Matrix ◽  
Brittle Matrix Composites

Failure Modes in Brittle Matrix Composites (BMC).

1998 ◽  
Author(s):  
Nicholas J. Pagano ◽  
G. P. Tandon ◽  
R. Y. Kim
Keyword(s):  
Failure Modes ◽  
Matrix Composites ◽  
Brittle Matrix ◽  
Brittle Matrix Composites

scholarly journals Characterization of the Structure, Mechanical Properties and Erosive Resistance of the Laser Cladded Inconel 625-Based Coatings Reinforced by TiC Particles

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2225
Author(s):  
Aleksandra Kotarska ◽  
Tomasz Poloczek ◽  
Damian Janicki
Keyword(s):  
Laser Cladding ◽  
Inconel 625 ◽  
Matrix Composites ◽  
Erosion Rates ◽  
Laser Cladding Process ◽  
Composition Variation ◽  
The Matrix ◽  
Reinforcing Material ◽  
Inconel 625 Superalloy

The article presents research in the field of laser cladding of metal-matrix composite (MMC) coatings. Nickel-based superalloys show attractive properties including high tensile strength, fatigue resistance, high-temperature corrosion resistance and toughness, which makes them widely used in the industry. Due to the insufficient wear resistance of nickel-based superalloys, many scientists are investigating the possibility of producing nickel-based superalloys matrix composites. For this study, the powder mixtures of Inconel 625 superalloy with 10, 20 and 40 vol.% of TiC particles were used to produce MMC coatings by laser cladding. The titanium carbides were chosen as reinforcing material due to high thermal stability and hardness. The multi-run coatings were tested using penetrant testing, macroscopic and microscopic observations, microhardness measurements and solid particle erosive test according to ASTM G76-04 standard. The TiC particles partially dissolved in the structure during the laser cladding process, which resulted in titanium and carbon enrichment of the matrix and the occurrence of precipitates formation in the structure. The process parameters and coatings chemical composition variation had an influence on coatings average hardness and erosion rates.

Sign in / Sign up

Export Citation Format

Share Document