scholarly journals Results of U-xMo (x=7, 10, 12 wt.%) Alloy versus Al-6061 Cladding Diffusion Couple Experiments Performed at 500, 550 and 600 Degrees C

2013 ◽  
Author(s):  
Emmanuel Perez ◽  
Jr. Dennis D. Keiser ◽  
Yongho Sohn
Keyword(s):  
Diffusion Couple ◽  
Al 6061 ◽  
Alloy Versus

Quantitative x-ray microanalysis and thickness determination using ζ factor

1996 ◽  
Vol 54 ◽  
pp. 580-581
Author(s):  
M. Watanabe ◽  
Z. Horita ◽  
M. Nemoto
Keyword(s):  
Diffusion Couple ◽  
Extrapolation Method ◽  
Thin Specimen ◽  
Beam Position ◽  
X Ray ◽  
Thickness Determination ◽  
Experimental Limitation ◽  
X Ray Absorption

X-ray absorption in quantitative x-ray microanalysis of thin specimens may be corrected without knowledge of thickness when the extrapolation method or the differential x-ray absorption (DXA) method is used. However, there is an experimental limitation involved in each method. In this study, a method is proposed to overcome such a limitation. The method is developed by introducing the ζ factor and by combining the extrapolation method and DXA method. The method using the ζ factor, which is called the ζ-DXA method in this study, is applied to diffusion-couple experiments in the Ni-Al system.For a thin specimen where incident electrons are fully transparent, the characteristic x-ray intensity generated from a beam position, I, may be represented as I = (NρW/A)Qωaist.

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

2019 ◽  
Vol 13 (4) ◽  
pp. 5804-5817
Author(s):  
Ibrahim Sabry
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Welded Joint ◽  
Rotation Speed ◽  
Fusion Welding ◽  
Friction Stir ◽  
Al 6061

It is expected that the demand for Metal Matrix Composite (MMCs) will increase in these applications in the aerospace and automotive industries sectors, strengthened AMC has different advantages over monolithic aluminium alloy as it has characteristics between matrix metal and reinforcement particles.  However, adequate joining technique, which is important for structural materials, has not been established for (MMCs) yet. Conventional fusion welding is difficult because of the irregular redistribution or reinforcement particles.  Also, the reaction between reinforcement particles and aluminium matrix as weld defects such as porosity in the fusion zone make fusion welding more difficult. The aim of this work was to show friction stir welding (FSW) feasibility for entering Al 6061/5 to Al 6061/18 wt. % SiCp composites has been produced by using stir casting technique. SiCp is added as reinforcement in to Aluminium alloy (Al 6061) for preparing metal matrix composite. This method is less expensive and very effective. Different rotational speeds,1000 and 1800 rpm and traverse speed 10 mm \ min was examined. Specimen composite plates having thick 10 mm were FS welded successfully. A high-speed steel (HSS) cylindrical instrument with conical pin form was used for FSW. The outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt. %) was 195 MPa at rotation speed 1800 rpm, the outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt.%) was 165 MPa at rotation speed 1000 rpm, that was very near to the composite matrix as-cast strength. The research of microstructure showed the reason for increased joint strength and microhardness. The microstructural study showed the reason (4 %) for higher joint strength and microhardness.  due to Significant   of SiCp close to the boundary of the dynamically recrystallized and thermo mechanically affected zone (TMAZ) was observed through rotation speed 1800 rpm. The friction stir welded ultimate tensile strength Decreases as the volume fraction increases of SiCp (18 wt.%).

Experimental Investigations on Friction Welding of AL 6061 and SS 304

2010 ◽  
Vol 43 (2) ◽  
pp. 25
Author(s):  
Ishtiaq Ahmed Khan ◽  
Ravinder Reddy ◽  
ACS Kumar ◽  
Yatin Tambe
Keyword(s):  
Friction Welding ◽  
Experimental Investigations ◽  
Al 6061 ◽  
Ss 304

scholarly journals EVALUATION OF THE PROPERTIES OF Al-6061 ALLOY REINFORCED WITH PARTICULATE WASTE GLASS

2021 ◽  
pp. e00812
Author(s):  
Adeolu Adesoji Adediran ◽  
Abayomi Adewale Akinwande ◽  
Oluwatosin Abiodun Balogun ◽  
Olanrewaju Seun Adesina ◽  
Adeniyi Olayanju ◽  
...  
Keyword(s):  
Waste Glass ◽  
Al 6061

Analysis of mechanical behavior of Al 6061 metal matrix with boron carbide and graphite

2021 ◽  
Author(s):  
SM. Sutharsan ◽  
P. Senthilkumar ◽  
B. Koodalingam ◽  
U. Nattarselvi ◽  
K. Murali Kumar ◽  
...  
Keyword(s):  
Boron Carbide ◽  
Mechanical Behavior ◽  
Metal Matrix ◽  
Al 6061
Sign in / Sign up

Export Citation Format

Share Document