scholarly journals Design of Isotope Heat Source for Automatic Modular Dispersal During Reentry, and Its Integration with Heat Exchangers of 6-kWe Dynamic Isotope Power System

1989 ◽  
Author(s):  
Alfred Schock
Keyword(s):  
Heat Source ◽  
Power System ◽  
Heat Exchangers

scholarly journals Analysis and Comparison of Some Low-Temperature Heat Sources for Heat Pumps

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1853 ◽  
Author(s):  
Pavel Neuberger ◽  
Radomír Adamovský
Keyword(s):  
Heat Transfer ◽  
Low Temperature ◽  
Heat Source ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Ambient Air ◽  
Heat Transfer Fluid ◽  
Heat Sources ◽  
Ground Heat Exchangers ◽  
Temperature Heat

The efficiency of a heat pump energy system is significantly influenced by its low-temperature heat source. This paper presents the results of operational monitoring, analysis and comparison of heat transfer fluid temperatures, outputs and extracted energies at the most widely used low temperature heat sources within 218 days of a heating period. The monitoring involved horizontal ground heat exchangers (HGHEs) of linear and Slinky type, vertical ground heat exchangers (VGHEs) with single and double U-tube exchanger as well as the ambient air. The results of the verification indicated that it was not possible to specify clearly the most advantageous low-temperature heat source that meets the requirements of the efficiency of the heat pump operation. The highest average heat transfer fluid temperatures were achieved at linear HGHE (8.13 ± 4.50 °C) and double U-tube VGHE (8.13 ± 3.12 °C). The highest average specific heat output 59.97 ± 41.80 W/m2 and specific energy extracted from the ground mass 2723.40 ± 1785.58 kJ/m2·day were recorded at single U-tube VGHE. The lowest thermal resistance value of 0.07 K·m2/W, specifying the efficiency of the heat transfer process between the ground mass and the heat transfer fluid, was monitored at linear HGHE. The use of ambient air as a low-temperature heat pump source was considered to be the least advantageous in terms of its temperature parameters.

scholarly journals Finite element modeling of geothermal source of heat pump in long-term operation

2020 ◽  
Vol 154 ◽  
pp. 04003
Author(s):  
Elżbieta Hałaj
Keyword(s):  
Finite Element ◽  
Heat Source ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Transport Model ◽  
Heat Pumps ◽  
Initial Temperature Distribution ◽  
Term Operation ◽  
Borehole Heat Exchangers

Heat pumps become more and more popular heat source. They can be an alternative choice for obsolete coal fired boilers which are emissive and not ecological. During heat pump installation designing process, especially for heat pumps with higher heating capacity (for example those suppling larger buildings), a simulation of heat balance of ground heat source must be provided. A 3D heat transport model and groundwater flow in the geothermal heat source for heat pump (GSHP) installation was developed in FEFLOW according to Finite Element Modelling Method. The model consists of 25 borehole heat exchangers, arranged with spacing recommended by heat pump branch guidelines. The model consists of both a homogeneous, non-layered domain and a layered domain, which reflected differences in thermal properties of the ground and hydrogeological factors. The initial temperature distribution in the ground was simulating according to conditions typical for Europe in steady state heat flow. Optimal mesh refinement for nodes around borehole heat exchangers were calculated according to Nillert method. The aim of this work is to present influence of geological, hydrogeological factors and borehole arrangement in the energy balance and long term sustainability of the ground source. The thermal changes in the subsurface have been determined for a long term operation (30 years of operation period). Some thermal energy storage applications have also been considered.

Experimental Study on the Organic Rankine Cycle Power System Adopting Dual Expanders in Parallel

2014 ◽  
Author(s):  
Eunkoo Yoon ◽  
Hyun Jun Park ◽  
Hyun Dong Kim ◽  
Kyung Chun Kim ◽  
Sang Youl Yoon
Keyword(s):  
Heat Source ◽  
Power System ◽  
Water Temperature ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Working Fluid ◽  
Electric Heater ◽  
Shaft Power ◽  
Scroll Expanders

This study aims to evaluate the performance of an organic Rankine cycle (ORC) power system adopting dual expanders in parallel by experiment. A dual-expander ORC system was designed to provide competitive advantages over a general single expander ORC system in typical applications with large thermal fluctuation of heat sources such as solar heat, marine waste heat, and etc. The ORC system consists of two scroll expanders installed in parallel, a hydraulic diaphragm type pump to feed and pressurize the working fluid, R-245fa, two plate heat exchangers for the evaporator and the condenser, and two generators with shaft power torque meters. The two scroll expanders were modified from two oil-free air scroll compressors, and were tested in the ORC loop with R245fa. The maximum isentropic efficiency of each expander was measured about 53%, and the shaft power was reached to about 2kW. The hot water was used as heat source, and the water temperature was controlled up to 150 °C by the 100 kW-class electric heater. A circulating air-cooled chiller was utilized for the control of the cooling water temperature. In order to determine the static performance of the system, efficiencies and shaft powers were measured with 130 °C heat source temperature. In addition, performance tests were conducted with various working fluid mass flow rates to control pressure ratios. The characteristics and total thermal efficiency of the dual parallel expander ORC system and optimal operating modes are addressed.

Analysis of the Zero-Pressure-Difference Point and Determination of the Pump Head in Distributed Power System

2013 ◽  
Vol 353-356 ◽  
pp. 2625-2630
Author(s):  
Yong Zheng Fu ◽  
Ming Liu Xu ◽  
Yang Jiao
Keyword(s):  
Energy Consumption ◽  
Heat Source ◽  
Power System ◽  
Critical Point ◽  
Pressure Difference ◽  
Total Output ◽  
Distributed Power ◽  
Distributed Power System ◽  
Pump Head ◽  
Transmission Energy Consumption

Using pressure diagram to analyze the pressure distribution of distributed power system when the zero-pressure-difference point is in different positions. Conclusions can be drawn as follows: the zero-pressure-difference point should be between the critical point and heat source to eliminate the energy consumption of regulators. And as a result the transmission energy consumption of the system becomes lowest. When the zero-pressure-difference point is in different positions between the critical point and heat source, arrangements of pumps of the system are different. But the total output power of the pumps is the same. The zero-pressure-difference point and the schemes for pump head can be conveniently determined by graphical method like pressure diagram or numerical method.

Sign in / Sign up

Export Citation Format

Share Document