scholarly journals Pressure drop, heat transfer, critical heat flux, and flow stability of two-phase flow boiling of water and ethylene glycol/water mixtures - final report for project "Efficent cooling in engines with nucleate boiling."

2011 ◽  
Author(s):  
W. Yu ◽  
D. M. France ◽  
J. L. Routbort
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Ethylene Glycol ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Final Report ◽  
Phase Flow ◽  
Two Phase

Two-Phase Pipe Quenching Correlations for Liquid Nitrogen and Liquid Hydrogen

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
S. R. Darr ◽  
J. W. Hartwig ◽  
J. Dong ◽  
H. Wang ◽  
A. K. Majumdar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Liquid Nitrogen ◽  
Critical Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Liquid Hydrogen ◽  
Two Phase ◽  
Cryogenic Flow ◽  
Two Phase Heat Transfer

Recently, two-phase cryogenic flow boiling data in liquid nitrogen (LN2) and liquid hydrogen (LH2) were compared to the most popular two-phase correlations, as well as correlations used in two of the most widely used commercially available thermal/fluid design codes in Hartwig et al. (2016, “Assessment of Existing Two Phase Heat Transfer Coefficient and Critical Heat Flux on Cryogenic Flow Boiling Quenching Experiments,” Int. J. Heat Mass Transfer, 93, pp. 441–463). Results uncovered that the correlations performed poorly, with predictions significantly higher than the data. Disparity is primarily due to the fact that most two-phase correlations are based on room temperature fluids, and for the heating configuration, not the quenching configuration. The penalty for such poor predictive tools is higher margin, safety factor, and cost. Before control algorithms for cryogenic transfer systems can be implemented, it is first required to develop a set of low-error, fundamental two-phase heat transfer correlations that match available cryogenic data. This paper presents the background for developing a new set of quenching/chilldown correlations for cryogenic pipe flow on thin, shorter lines, including the results of an exhaustive literature review of 61 sources. New correlations are presented which are based on the consolidated database of 79,915 quenching points for a 1.27 cm diameter line, covering a wide range of inlet subcooling, mass flux, pressure, equilibrium quality, flow direction, and even gravity level. Functional forms are presented for LN2 and LH2 chilldown correlations, including film, transition, and nucleate boiling, critical heat flux, and the Leidenfrost point.

scholarly journals A Separated-Flow Model for Predicting Flow Boiling Critical Heat Flux and Pressure Drop Characteristics in Microchannels

2012 ◽  
Author(s):  
Tie Jun Zhang ◽  
Siyu Chen ◽  
Evelyn N. Wang
Keyword(s):  
Heat Flux ◽  
Pressure Drop ◽  
Critical Heat Flux ◽  
Flow Model ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Separated Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Microchannel Cooling

Two-phase microchannel cooling promises high heat flux removal for high-performance electronics and photonics. However, the heat transfer performance of flow boiling microchannels is limited by the critical heat flux (CHF) conditions. For variable heat inputs and variable fluid flows, it is essential to predict CHFs accurately for effective and efficient two-phase microchannel cooling. To characterize the CHF and pressure drop in flow boiling microchannels, a separated-flow model is proposed in this paper based on fundamental two-phase flow mass, energy, momentum conservation and wall energy conservation laws. With this theoretical framework, the relationship among liquid/vapor interfacial instability, two-phase flow characteristics and CHF is further studied. This mechanistic model also provides insight into the design and operational guidelines for advanced electronics and photonics cooling technologies.

Study on Subcooled-Forced Flow Boiling Heat Transfer and Critical Heat Flux of Solid-Water Two-Phase Mixture

1999 ◽  
Author(s):  
Yasuo Koizumi ◽  
Hiroyasu Ohtake ◽  
Manabu Mochizuki
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Liquid Layer ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Forced Flow ◽  
Superheated Liquid ◽  
Flow Boiling Heat Transfer

Abstract The effect of solid particle introduction on subcooled-forced flow boiling heat transfer and a critical heat flux was examined experimentally. In the experiment, glass beads of 0.6 mm diameter were mixed in subcooled water. Experiments were conducted in a range of the subcooling of 40 K, a velocity of 0.17–6.7 m/s, a volumetric particle ratio of 0–17%. When particles were introduced, the growth of a superheated liquid layer near a heat trasnsfer surface seemed to be suppressed and the onset of nucleate boiling was delayed. The particles promoted the condensation of bubbles on the heat transfer surface, which shifted the initiation of a net vapor generation to a high heat flux region. Boiling heat trasnfer was augmented by the particle introduction. The suppression of the growth of the superheated liquid layer and the promotion of bubble condensation and dissipation by the particles seemed to contribute that heat transfer augmentation. The wall superheat at the critical heat flux was elevated by the particle introduction and the critical heat flux itself was also enhanced. However, the degree of the critical heat flux improvement was not drastic.

Flow Boiling Heat Transfer and Two-Phase Flow Instability of Nanofluids in a Minichannel

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Leyuan Yu ◽  
Aritra Sur ◽  
Dong Liu
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Two Phase Flow ◽  
Flow Instability ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
Flow Instabilities ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Boiling Heat Transfer

Single-phase convective heat transfer of nanofluids has been studied extensively, and different degrees of enhancement were observed over the base fluids, whereas there is still debate on the improvement in overall thermal performance when both heat transfer and hydrodynamic characteristics are considered. Meanwhile, very few studies have been devoted to investigating two-phase heat transfer of nanofluids, and it remains inconclusive whether the same pessimistic outlook should be expected. In this work, an experimental study of forced convective flow boiling and two-phase flow was conducted for Al2O3–water nanofluids through a minichannel. General flow boiling heat transfer characteristics were measured, and the effects of nanofluids on the onset of nucleate boiling (ONB) were studied. Two-phase flow instabilities were also explored with an emphasis on the transition boundaries of onset of flow instabilities (OFI). It was found that the presence of nanoparticles delays ONB and suppresses OFI, and the extent is correlated to the nanoparticle volume concentration. These effects were attributed to the changes in available nucleation sites and surface wettability as well as thinning of thermal boundary layers in nanofluid flow. Additionally, it was observed that the pressure-drop type flow instability prevails in two-phase flow of nanofluids, but with reduced amplitude in pressure, temperature, and mass flux oscillations.

Effect of Inlet Restriction on Flow Boiling Heat Transfer in a Horizontal Microtube

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
YanFeng Fan ◽  
Ibrahim Hassan
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Critical Heat Flux ◽  
Mass Flux ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Mass Fluxes ◽  
Flow Boiling Heat Transfer ◽  
Low Mass

Flow boiling heat transfer in a horizontal microtube with inlet restriction (orifice) under uniform heating condition is experimentally investigated using FC-72 as working fluid. A stainless steel microtube with an inner diameter of 889 μm is selected as main microtube. Two microtubes with smaller diameters are assembled at the inlet of main microtube to achieve the restriction ratios of 50% and 20%. The experimental measurement is carried out at mass fluxes ranging from 160 to 870 kg/m2·s, heat fluxes varying from 6 to 170 kW/m2, inlet temperatures of 23 and 35 °C, and saturation pressures of 10 and 45 kPa. The effects of the orifices on two-phase pressure drop, critical heat flux (CHF), and flow boiling heat transfer coefficient are studied. The results show that the pressure drop caused by the orifice takes a considerable portion in the total pressure drop at low mass fluxes. This ratio decreases as the vapor quality or mass flux increases. The difference of normal critical heat flux in the microtubes with different orifice sizes is negligible. In the aspect of flow boiling heat transfer, the orifice is able to enhance the heat transfer at low mass flux and high saturation pressure, which indicates the contribution of orifice in the nucleate boiling dominated regime. However, the effect of orifice on flow boiling heat transfer is negligible in the forced convective boiling dominated regime.

Two-Phase Flow and Heat Transfer in Rectangular Micro-Channels

2004 ◽  
Vol 126 (3) ◽  
pp. 288-300 ◽  
Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Pattern ◽  
Two Phase Flow ◽  
Flow Boiling ◽  
Flow Patterns ◽  
Heat Sinks ◽  
Phase Flow ◽  
Micro Channel ◽  
Two Phase

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406×2.032mm2 cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Features unique to two-phase micro-channel flow were identified and employed to validate key assumptions of an annular flow boiling model that was previously developed to predict pressure drop and heat transfer in two-phase micro-channel heat sinks. This earlier model was modified based on new findings from the adiabatic two-phase flow study. The modified model shows good agreement with experimental data for water-cooled heat sinks.

Sign in / Sign up

Export Citation Format

Share Document