SOIL SHEAR MODULUS FROM RESONANT COLUMN, TORSIONAL SHEAR AND BENDER ELEMENT TESTS

2016 ◽  
Author(s):  
Zsolt Szilvágyi,
Keyword(s):  
Shear Modulus ◽  
Resonant Column ◽  
Bender Element ◽  
Torsional Shear

Measurement of small-strain shear modulus Gmax of dry and saturated sands by bender element, resonant column, and torsional shear tests

2008 ◽  
Vol 45 (10) ◽  
pp. 1426-1438 ◽  
Author(s):  
Jun-Ung Youn ◽  
Yun-Wook Choo ◽  
Dong-Soo Kim
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Shear Wave Velocity ◽  
Small Strain ◽  
Resonant Column ◽  
Test Results ◽  
Bender Element ◽  
Small Strain Shear Modulus ◽  
Torsional Shear ◽  
Saturated Sands

The bender element method is an experimental technique used to determine the small-strain shear modulus (Gmax) of a soil by measuring the velocity of shear wave propagation through a sample. Bender elements have been applied as versatile transducers to measure the Gmax of wet and dry soils in various laboratory apparatuses. However, certain aspects of the bender element method have yet to be clearly specified because of uncertainties in determining travel time. In this paper, the bender element (BE), resonant column (RC), and torsional shear (TS) tests were performed on the same specimens using the modified Stokoe-type RC and TS testing equipment. Two clean sands, Toyoura and silica sands, were tested at various densities and mean effective stresses under dry and saturated conditions. Based on the test results, methods of determining travel time in BE tests were evaluated by comparing the results of RC, TS, and BE tests. Also, methods to evaluate Gmax of saturated sands from the shear-wave velocity (Vs) obtained by RC and BE tests were investigated by comparing the three sets of test results. Biot’s theory on frequency dependence of shear-wave velocity was adopted to consider dispersion of a shear wave in saturated conditions. The results of this study suggest that the total mass density, which is commonly used to convert Gmax from the measured Vs in saturated soils, should not be used to convert Vs to Gmax when the frequency of excitation is 10% greater than the characteristic frequency (fc) of the soil.

scholarly journals Evaluation of Dynamic Properties of Sodium-Alginate-Reinforced Soil Using A Resonant-Column Test

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2743
Author(s):  
Seongnoh Ahn ◽  
Jae-Eun Ryou ◽  
Kwangkuk Ahn ◽  
Changho Lee ◽  
Jun-Dae Lee ◽  
...  
Keyword(s):  
Shear Modulus ◽  
Sodium Alginate ◽  
Shear Failure ◽  
Dynamic Properties ◽  
Damping Ratio ◽  
Reinforced Soil ◽  
Resonant Column ◽  
Column Test ◽  
Alginate Solution ◽  
Resonant Column Test

Ground reinforcement is a method used to reduce the damage caused by earthquakes. Usually, cement-based reinforcement methods are used because they are inexpensive and show excellent performance. Recently, however, reinforcement methods using eco-friendly materials have been proposed due to environmental issues. In this study, the cement reinforcement method and the biopolymer reinforcement method using sodium alginate were compared. The dynamic properties of the reinforced ground, including shear modulus and damping ratio, were measured through a resonant-column test. Also, the viscosity of sodium alginate solution, which is a non-Newtonian fluid, was also explored and found to increase with concentration. The maximum shear modulus and minimum damping ratio increased, and the linear range of the shear modulus curve decreased, when cement and sodium alginate solution were mixed. Addition of biopolymer showed similar reinforcing effect in a lesser amount of additive compared to the cement-reinforced ground, but the effect decreased above a certain viscosity because the biopolymer solution was not homogeneously distributed. This was examined through a shear-failure-mode test.

Bender Element Measurement for Small-Strain Shear Modulus of Compacted Loess

2021 ◽  
Vol 21 (5) ◽  
pp. 04021063
Author(s):  
Fangtong Wang ◽  
Dianqing Li ◽  
Wenqi Du ◽  
Chia Zarei ◽  
Yong Liu
Keyword(s):  
Shear Modulus ◽  
Small Strain ◽  
Bender Element ◽  
Small Strain Shear Modulus ◽  
Compacted Loess

Bender Element Test and Numerical Simulation of Sliding Zone Soil with Gravels of Huangtupo Landslide

2021 ◽  
Author(s):  
Yu Chen
Keyword(s):  
Shear Modulus ◽  
Shear Wave ◽  
Wave Velocity ◽  
Small Strain ◽  
Testing System ◽  
Bender Element ◽  
Gravel Content ◽  
Consolidation Pressure ◽  
Bender Element Test ◽  
Sliding Zone

<p>In order to study the effect of the different consolidation pressure, loading-unloading path and gravel content on the shear modulus of the small strain of sliding zone soil, a set of consolidation bender element test device was developed. The device consists of three parts: a consolidation system, a deformation measuring system, and a shear wave testing system. The consolidation system is composed of a traditional consolidation instrument and the plexiglass cylinder box. The sample is cylindrical in shape and has a size of 50 mm×50 mm. The consolidation displacement is measured by a digital display micrometer. Shear wave testing system is a wave velocity measurement system made of piezoelectric ceramic. The experimental results show that the device can control the consolidation pressure and measure the vertical deformation, measure the shear wave velocity of the sliding zone soil in real-time, and then study the variation rule of the small strain shear modulus of the sliding zone soil with gravels. The shear modulus of the sliding zone soil increases with an increase in the consolidation pressure. The shear modulus of the unloading of sliding zone soil is larger than that of loading. Under the loading pressure of 200 kPa and 400 kPa, the shear modulus of the sliding zone soil first decreases and then increases with an increase in the gravel content. In the process of unloading, the shear modulus of the sliding zone soil increases with an increase in the gravel content. </p>

Sign in / Sign up

Export Citation Format

Share Document