scholarly journals Process schemes for future energy-positive water resource recovery facilities

2019 ◽  
Vol 79 (9) ◽  
pp. 1808-1820 ◽  
Author(s):  
Kimberly Solon ◽  
Mingsheng Jia ◽  
Eveline I. P. Volcke
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Water Resource ◽  
Municipal Wastewater ◽  
Energy Savings ◽  
Wastewater Treatment Plants ◽  
Resource Recovery ◽  
High Rate ◽  
Plant Performance ◽  
Municipal Wastewater Treatment

Abstract There are numerous successful studies on optimizing the performance of conventional activated sludge (CAS)-based wastewater treatment plants. However, recent studies have shown that a more significant improvement of the plant performance is achievable through integration of established technologies in novel process schemes. High-rate activated sludge system, chemically enhanced primary treatment, partial nitritation-anammox, partial nitrification-denitrification over nitrite and anaerobic digestion are integrated in two process schemes to determine to which extent energy savings and energy production can be achieved with these new process layouts compared to a CAS-based process scheme. The results presented in this paper show that there is potential for achieving future energy-positive water resource recovery facilities through novel integration of mature technologies for municipal wastewater treatment.

PARAMETERS FOR DYNAMIC SIMULATION OF W ASTEW ATER TREATMENT PLANTS WITH HIGH-RATE AND LOW-RATE ACTIVATED SLUDGE TANKS

1994 ◽  
Vol 30 (4) ◽  
pp. 211-214 ◽  
Author(s):  
E. Brands ◽  
M. Liebeskind ◽  
M. Dohmann
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Dynamic Simulation ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
High Rate ◽  
Yield Coefficient ◽  
Municipal Wastewater Treatment ◽  
Municipal Wastewater Treatment Plants ◽  
Low Rate

This study shows a comparison of important parameters for dynamic simulation concerning the highrate and low-rate activated sludge tanks of several municipal wastewater treatment plants. The parameters for the dynamic simulation of the single-stage process are quite well known, but parameters for the high-ratellow-rate activated sludge process are still missi ng, although a considerable number of wastewater treatment plants are designed and operated that way. At present any attempt to simulate their operation is restricted to the second stage due to missing data concerning growth rate, decay rate, yield coefficient and others.

Characterization of wastewater and activated sludge from European municipal wastewater treatment plants using the NUR test

1998 ◽  
Vol 38 (1) ◽  
pp. 303-310 ◽  
Author(s):  
V. Naidoo ◽  
V. Urbain ◽  
C. A. Buckley
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Municipal Wastewater Treatment ◽  
Batch Tests ◽  
Denitrification Kinetics ◽  
Municipal Wastewater Treatment Plants

Denitrification kinetics and wastewater characterization of eight different plants in Europe are discussed. Denitrification batch tests revealed three distinct rates except in the cases of Plaisir, Rostock and Orense where 4 rates were observed. The latter three plants revealed atypical rapid initial rates which were between 7 and 21 mgN/gVSS.h. All denitrification kinetics under non-limiting carbon conditions revealed fast first rates which ranged between 3.0 and 7.3 mgN/gVSS.h. Acetate was used to simulate denitrification kinetics with readily biodegradable COD present. Two subsequent rates were observed. Rates 2 and 3 ranged between 2 and 3 mgN/gVSS.h, and 1 and 2 mgN/gVSS.h, respectively. The RBCOD fraction varied between 10 and 19%, except for one of the plants where the value determined was 7%.

Integrated Wastewater Treatment Plant Performance Evaluation Using Artificial Neural Networks

1999 ◽  
Vol 40 (7) ◽  
pp. 55-65 ◽  
Author(s):  
Mohamed F. Hamoda ◽  
Ibrahim A. Al-Ghusain ◽  
Ahmed H. Hassan
Keyword(s):  
Neural Networks ◽  
Wastewater Treatment ◽  
Artificial Neural Networks ◽  
Wastewater Treatment Plant ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Plant Performance ◽  
Municipal Wastewater Treatment ◽  
Artificial Neural

Proper operation of municipal wastewater treatment plants is important in producing an effluent which meets quality requirements of regulatory agencies and in minimizing detrimental effects on the environment. This paper examined plant dynamics and modeling techniques with emphasis placed on the digital computing technology of Artificial Neural Networks (ANN). A backpropagation model was developed to model the municipal wastewater treatment plant at Ardiya, Kuwait City, Kuwait. Results obtained prove that Neural Networks present a versatile tool in modeling full-scale operational wastewater treatment plants and provide an alternative methodology for predicting the performance of treatment plants. The overall suspended solids (TSS) and organic pollutants (BOD) removal efficiencies achieved at Ardiya plant over a period of 16 months were 94.6 and 97.3 percent, respectively. Plant performance was adequately predicted using the backpropagation ANN model. The correlation coefficients between the predicted and actual effluent data using the best model was 0.72 for TSS compared to 0.74 for BOD. The best ANN structure does not necessarily mean the most number of hidden layers.

scholarly journals Improving and upgrading an existing activated sludge with a compact MBBR – disc filters parallel line for municipal wastewater treatment in touristic alpine areas

2020 ◽  
Vol 15 (2) ◽  
pp. 515-527
Author(s):  
L. Desa ◽  
P. Kängsepp ◽  
L. Quadri ◽  
G. Bellotti ◽  
K. Sørensen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Parallel Line ◽  
Ammonium Nitrogen ◽  
Biofilm Reactor ◽  
Municipal Wastewater Treatment ◽  
Yearly Average

Abstract Many wastewater treatment plants (WWTP) in touristic areas struggle to achieve the effluent requirements due to seasonal variations in population. In alpine areas, the climate also determines a low wastewater temperature, which implies long sludge retention time (SRT) needed for the growth of nitrifying biomass in conventional activated sludge (CAS). Moreover, combined sewers generate high flow and dilution. The present study shows how the treatment efficiency of an existing CAS plant with tertiary treatment can be upgraded by adding a compact line in parallel, consisting of a Moving Bed Biofilm Reactor (MBBR)-coagulation-flocculation-disc filtration. This allows the treatment of influent variations in the MBBR and a constant flow supply to the activated sludge. The performance of the new 2-step process was comparable to that of the improved existing one. Regardless significant variations in flow (10,000–25,000 m3/d) and total suspended solids (TSS) (50–300 mg/L after primary treatment) the effluent quality fulfilled the discharge requirements. Based on yearly average effluent data, TSS were 11 mg/L, chemical oxygen demand (COD) 27 mg/L and total phosphorus (TP) 0.8 mg/L. After the upgrade, ammonium nitrogen (NH4-N) dropped from 4.9 mg/L to 1.3 mg/L and the chemical consumption for phosphorus removal was reduced.

scholarly journals LCA of a Membrane Bioreactor Compared to Activated Sludge System for Municipal Wastewater Treatment

Membranes ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 421
Author(s):  
Dimitra C. Banti ◽  
Michail Tsangas ◽  
Petros Samaras ◽  
Antonis Zorpas
Keyword(s):  
Wastewater Treatment ◽  
Life Cycle ◽  
Activated Sludge ◽  
Membrane Bioreactor ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Real Data ◽  
Municipal Wastewater Treatment ◽  
Conventional Activated Sludge

Membrane bioreactor (MBR) systems are connected to several advantages compared to the conventional activated sludge (CAS) units. This work aims to the examination of the life cycle environmental impact of an MBR against a CAS unit when treating municipal wastewater with similar influent loading (BOD = 400 mg/L) and giving similar high-quality effluent (BOD < 5 mg/L). The MBR unit contained a denitrification, an aeration and a membrane tank, whereas the CAS unit included an equalization, a denitrification, a nitrification, a sedimentation, a mixing, a flocculation tank and a drum filter. Several impact categories factors were calculated by implementing the Life Cycle Assessment (LCA) methodology, including acidification potential, eutrophication potential, global warming potential (GWP), ozone depletion potential and photochemical ozone creation potential of the plants throughout their life cycle. Real data from two wastewater treatment plants were used. The research focused on two parameters which constitute the main differences between the two treatment plants: The excess sludge removal life cycle contribution—where GWPMBR = 0.50 kg CO2-eq*FU−1 and GWPCAS = 2.67 kg CO2-eq*FU−1 without sludge removal—and the wastewater treatment plant life cycle contribution—where GWPMBR = 0.002 kg CO2-eq*FU−1 and GWPCAS = 0.14 kg CO2-eq*FU−1 without land area contribution. Finally, in all the examined cases the environmental superiority of the MBR process was found.

scholarly journals Benchmarking of energy consumption in municipal wastewater treatment plants – a survey of over 200 plants in Italy

2018 ◽  
Vol 77 (9) ◽  
pp. 2242-2252 ◽  
Author(s):  
M. Vaccari ◽  
P. Foladori ◽  
S. Nembrini ◽  
F. Vitali
Keyword(s):  
Wastewater Treatment ◽  
Energy Consumption ◽  
Municipal Wastewater ◽  
Energy Savings ◽  
Wastewater Treatment Plants ◽  
Specific Energy Consumption ◽  
Oxygen Demand ◽  
Energy Performance ◽  
High Energy ◽  
Municipal Wastewater Treatment

Abstract One of the largest surveys in Europe about energy consumption in Italian wastewater treatment plants (WWTPs) is presented, based on 241 WWTPs and a total population equivalent (PE) of more than 9,000,000 PE. The study contributes towards standardised resilient data and benchmarking and to identify potentials for energy savings. In the energy benchmark, three indicators were used: specific energy consumption expressed per population equivalents (kWh PE−1 year−1), per cubic meter (kWh/m3), and per unit of chemical oxygen demand (COD) removed (kWh/kgCOD). The indicator kWh/m3, even though widely applied, resulted in a biased benchmark, because highly influenced by stormwater and infiltrations. Plants with combined networks (often used in Europe) showed an apparent better energy performance. Conversely, the indicator kWh PE−1 year−1 resulted in a more meaningful definition of a benchmark. High energy efficiency was associated with: (i) large capacity of the plant, (ii) higher COD concentration in wastewater, (iii) separate sewer systems, (iv) capacity utilisation over 80%, and (v) high organic loads, but without overloading. The 25th percentile was proposed as a benchmark for four size classes: 23 kWh PE−1 y−1 for large plants &gt; 100,000 PE; 42 kWh PE−1 y−1 for capacity 10,000 &lt; PE &lt; 100,000, 48 kWh PE−1 y−1 for capacity 2,000 &lt; PE &lt; 10,000 and 76 kWh PE−1 y−1 for small plants &lt; 2,000 PE.

scholarly journals Initiating Biodegradation of Polyvinylpyrrolidone in an Aqueous Aerobic Environment: Technical Note / Zainicjowanie Biodegradacji Poliwinylopirolidonu W Środowisku Wodno-Tlenowym: Notatki Techniczne

2013 ◽  
Vol 20 (1) ◽  
pp. 199-208 ◽  
Author(s):  
Marketa Julinova ◽  
Jan Kupec ◽  
Roman Slavik ◽  
Maria Vaskova
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Waste Treatment ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Technical Note ◽  
Aerobic Biodegradation ◽  
Municipal Wastewater Treatment

Abstract A synthetic polymer, polyvinylpyrrolidone (PVP - E 1201) primarily finds applications in the pharmaceutical and food industries due to its resistance and zero toxicity to organisms. After ingestion, the substance passes through the organism unchanged. Consequently, it enters the systems of municipal wastewater treatment plants (WWTP) without decomposing biologically during the waste treatment process, nor does it attach (through sorption) to particles of activated sludge to any significant extent, therefore, it passes through the system of a WWTP, which may cause the substance to accumulate in the natural environment. For this reason the paper investigates the potential to initiate aerobic biodegradation of PVP in the presence of activated sludge from a municipal wastewater treatment plant. The following agents were selected as the initiators of the biodegradation process - co-substrates: acrylamide, N-acethylphenylalanine and 1-methyl-2-pyrrolidone, a substance with a similar structure to PVP monomer. The biodegradability of PVP in the presence of co-substrates was evaluated on the basis of biological oxygen demand (BOD) as determined via a MicroOxymax O2/CO2/CH4 respirometer. The total substrate concentration in the suspension equaled 400 mg·dm-3, with the ratio between PVP and the cosubstrate being 1:1, while the concentration of the dry activated sludge was 500 mg·dm-3. Even though there was no occurrence of a significant increase in the biodegradation of PVP alone in the presence of a co-substrate, acrylamide appeared to be the most effective type of co-substrate. Nevertheless, a recorded decrease in the slope of biodegradation curves over time may indicate that a process of primary decomposition was underway, which involves the production of metabolites that inhibit activated sludge microorganisms. The resulting products are not identified at this stage of experimentation.

Sign in / Sign up

Export Citation Format

Share Document