Sensitivity analysis of the WATER9 model: emissions of odorous compounds from passive liquid surfaces present in wastewater treatment plants

2018 ◽  
Vol 2017 (3) ◽  
pp. 903-912
Author(s):  
Milena J. Calvo ◽  
Ademir A. Prata ◽  
Leonardo Hoinaski ◽  
Jane M. Santos ◽  
Richard M. Stuetz

Abstract Empirical mathematical models have been frequently used to estimate emissions and to act in the prevention of possible impacts from odorous compounds. Based on the regulatory WATER9 model, the present study had the aim to evaluate the deviations originating from the simplification of using the effective diameter (in contrast to the conceptually appropriate use of the linear physical fetch) as fetch parameter in the calculation of the global mass transfer coefficient at passive liquid surfaces at wastewater treatment plants (WWTPs). The present analysis incorporated the influence of different values of wind velocity, molecular diffusivity and Henry's Law constant. The analyses for the calculation of the mass transfer coefficients were developed for 1,000 wind speeds, chosen using the Monte Carlo method, three WWTPs and three compounds of environmental relevance, spanning different behaviour regarding their volatilisation. The wind speed had a direct influence on the deviations for all types of compounds analysed. However, this parameter was found to be more representative for the compounds whose volatilisation is limited by conditions in the liquid phase. Furthermore, the deviations for the calculation of the mass transfer coefficient arising from the use of the effective diameter as fetch parameter were significantly larger for liquid phase-dominated compounds, compared to gas phase-dominated compounds. Comparison against available experimental data confirm that the use of the effective diameter as the fetch parameter makes the model predictions further depart from the experimental values. The present analysis shows that, for a varied range of wind speed and WWTP configurations, the use of the actual physical fetch shall be preferred over the use of the effective diameter in emission models for WWTPs, so as to avoid the introduction of potentially large systematic deviations.

2016 ◽  
Vol 74 (10) ◽  
pp. 2384-2391 ◽  
Author(s):  
Ademir A. Prata ◽  
Milena J. Calvo ◽  
Gaetano Boncardo ◽  
Eric C. Sivret ◽  
Jane M. Santos ◽  
...  

Passive liquid surfaces in wastewater treatment plants may be potential sources of odorous emissions. This study investigates the occurrence and significance of deviations that may originate from the use of the effective diameter as fetch parameter in the empirical correlations utilised by the WATER9 model to estimate odorous emissions at passive liquid surfaces. A sensitivity analysis was performed using benzene as a model compound and considering representative conditions of wind speed and wind alignment. The gas-film mass transfer coefficient (kG) was found relatively in sensitive to the choice of the fetch parameter, deviating less than 15% for aspect rations up to 15. The calculation of the liquid-film mass transfer coefficient (kL) was much more sensitive (positive extreme of 126.98% and negative extreme of −54.80%), partially because of the use of different equations for different fetch-to-depth ratios. For more volatile compounds, such as benzene, these discrepancies will be significantly manifested in the estimated emission rate. When appropriate, the use of the actual fetch instead of the effective diameter is recommended.


2016 ◽  
Vol 10 (8) ◽  
pp. 142 ◽  
Author(s):  
Gustavo Andrés Baquero-Rodríguez ◽  
Jaime A. Lara-Borrero

Aeration is usually the most energy intensive part of the wastewater treatment process. Optimizing the aeration system is essential for reducing energy costs. Field tests oriented to estimate parameters related to oxygen transfer are a common approach to compare aeration systems. The aim of this research is to assess the effect of dissolved oxygen probe lag on oxygen transfer parameter estimation. Experimental procedures regarding to process automation and control were applied to quantify dissolved oxygen probe lag. We have measured oxygen transfer in clean water, under a wide range of conditions (airflow rate, diffuser characteristics and diffuser density), with optic and polarographic sensors for dissolved oxygen measurement. The oxygen transfer was measured as per ASCE Standard procedures. Nonparametric statistical tests were used to compare the estimated volumetric mass transfer coefficient KLa with different sensors. According to the results, there is not significant influence of the probe lag (also known as time constant) or probe characteristics on the parameters used to assess oxygen transfer efficiency. This fact has great relevance in common practice of aerobic process for wastewater treatment because dissolved oxygen monitoring is used as an input for decision making related to the energy optimization in the aeration system. Findings from these tests contradict previous studies which claim that lag time in polarographic sensors for the dissolved oxygen measurement can bias estimate KLa.


2021 ◽  
Vol 25 (2) ◽  
pp. 18-22
Author(s):  
Yu.V. Solovyova ◽  
V.P. Yustratov ◽  
N.S. Golubeva ◽  
I.V. Vasiljeva ◽  
E.V. Nazimova

The regularities and mechanism of adsorption of dimethylformamide and dimethylamine by industrial activated carbon in their joint presence from aqueous solutions are considered. The characteristics of equilibrium adsorption, the limiting stage, and the mass transfer coefficient have been determined. The main parameters of the adsorption column process and the mode of continuous cleaning are calculated by the method of mathematical modeling.


EKUILIBIUM ◽  
2011 ◽  
Vol 10 (2) ◽  
Author(s):  
Endang Kwartiningsih ◽  
Arif Jumari

<p><strong><em>Abstract:</em></strong><strong><em> </em></strong><em>Gas purification from the content of H<sub>2</sub>S using  Fe-EDTA (Iron Chelated Solution) gave  several advantages. The advantages were  the absorbent solution can be regenerated that means  a cheap operation cost,  the separated sulfur was a solid that is easy to handle and is save to be disposal to environment. This research was done by simulation and experimental. The simulation step was done by mathematical model arrangement representing the absorption process in packed column through mass transfer arrangement such as mass transfer equations and chemical reaction. The experimental step was done with the making of Fe-EDTA solution from FeCl<sub>2</sub> and EDTA. Then Fe-EDTA solution was flown in counter current packed column that was contacted with H<sub>2</sub>S in the methane gas. By comparing gas composition result of experiment and simulation, the value of mass transfer coefficient in gas phase ( k<sub>Ag</sub>a), mass transfer coefficient in liquid phase (k<sub>Al</sub>a) and the reaction rate constant ( k) were found. The values of mass transfer coefficient in liquid phase (k<sub>Al</sub>a) were lower than values of mass transfer coefficient in gas phase (k<sub>Ag</sub>a) and the reaction rate constant (k). It meant that H<sub>2</sub>S absorption  process using Fe-EDTA absorbent solution was determined by mass transfer process in liquid phase. The higher flow rate of absorbent, the higher value of mass transfer coefficient in liquid phase. </em><em>The smaller packing diameter, the higher value of mass transfer coefficient in liquid phase.From analysis of dimension, the relation of dimensionless number between Sherwood number and flow rate of absorbent, packing diameter was</em><strong></strong></p><p> <strong><em>Keywords:</em></strong><strong><em> </em></strong><em>chemical reaction, Fe-EDTA, H<sub>2</sub>S absorption, mass transfer</em></p>


2008 ◽  
Vol 141 (1-3) ◽  
pp. 278-283 ◽  
Author(s):  
Lishun Hu ◽  
Xinjun Wang ◽  
Guangsuo Yu ◽  
Fuchen Wang ◽  
Zunhong Yu

Sign in / Sign up

Export Citation Format

Share Document