Low cost Fenton's oxidative degradation of 4-nitroaniline using iron from laterite

2016 ◽  
Vol 74 (8) ◽  
pp. 1919-1925 ◽  
Author(s):  
A. S. Amritha ◽  
B. Manu
Keyword(s):  
Low Cost ◽  
Oxidative Degradation ◽  
Cost Effective ◽  
Fenton’S Oxidation ◽  
Cost Effective Method ◽  
Optimum Ph ◽  
The Subject ◽  
The Cost ◽  
Fenton's Oxidation ◽  
Maximum Removal

The present study aims to establish the use of iron (Fe) from larerite in the case of Fenton's oxidation process which is a simple and cost-effective method for degradation of nitro compounds in effluents and in surface or ground water. 4-nitroaniline (4-NA) degradation by Fenton's oxidation method is the subject of the present study so as to optimize pH, hydrogen peroxide/iron (H/F) ratio at different initial concentrations of 4-NA. The optimum pH obtained was 3. The present study has also established optimum H/F ratio for the different initial concentrations of 4-NA for both conventional and use of Fe from laterite. The maximum removal efficiency of 99.84% was obtained for an H/F ratio of 100 for 0.5 mM initial concentration of 4-NA. The study establishes the use of Fe extracted from locally available laterite soil (LS) as a replacement of Fe salts so as to reduce the cost of the process.

CAD Of Anticorrosive Protection Of Steel Structures

2019 ◽  
pp. 18-23
Keyword(s):  
Protective Coating ◽  
Computer Aided Design ◽  
Steel Structures ◽  
Cost Effective ◽  
Operating Conditions ◽  
Computational Tool ◽  
Protection Method ◽  
Cost Effective Method ◽  
The Cost ◽  
Aided Design

The choice of cost-effective method of anticorrosive protection of steel structures is an urgent and time consuming task, considering the significant number of protection ways, differing from each other in the complex of technological, physical, chemical and economic characteristics. To reduce the complexity of solving this problem, the author proposes a computational tool that can be considered as a subsystem of computer-aided design and used at the stage of variant and detailed design of steel structures. As a criterion of the effectiveness of the anti-corrosion protection method, the cost of the protective coating during the service life is accepted. The analysis of existing methods of steel protection against corrosion is performed, the possibility of their use for the protection of the most common steel structures is established, as well as the estimated period of effective operation of the coating. The developed computational tool makes it possible to choose the best method of protection of steel structures against corrosion, taking into account the operating conditions of the protected structure and the possibility of using a protective coating.

Janus – A New Approach to Air Combat Pilot Training

2019 ◽  
Vol 2019 (4) ◽  
pp. 7-22
Author(s):  
Georges Bridel ◽  
Zdobyslaw Goraj ◽  
Lukasz Kiszkowiak ◽  
Jean-Georges Brévot ◽  
Jean-Pierre Devaux ◽  
...  
Keyword(s):  
Low Cost ◽  
Cost Effective ◽  
High Energy ◽  
Training System ◽  
Embedded Sensors ◽  
Pilot Training ◽  
New Approach ◽  
Combat Aircraft ◽  
Air Combat ◽  
The Cost

Abstract Advanced jet training still relies on old concepts and solutions that are no longer efficient when considering the current and forthcoming changes in air combat. The cost of those old solutions to develop and maintain combat pilot skills are important, adding even more constraints to the training limitations. The requirement of having a trainer aircraft able to perform also light combat aircraft operational mission is adding unnecessary complexity and cost without any real operational advantages to air combat mission training. Thanks to emerging technologies, the JANUS project will study the feasibility of a brand-new concept of agile manoeuvrable training aircraft and an integrated training system, able to provide a live, virtual and constructive environment. The JANUS concept is based on a lightweight, low-cost, high energy aircraft associated to a ground based Integrated Training System providing simulated and emulated signals, simulated and real opponents, combined with real-time feedback on pilot’s physiological characteristics: traditionally embedded sensors are replaced with emulated signals, simulated opponents are proposed to the pilot, enabling out of sight engagement. JANUS is also providing new cost effective and more realistic solutions for “Red air aircraft” missions, organised in so-called “Aggressor Squadrons”.

scholarly journals Growth and biochemical composition of Chlorella vulgaris in different growth media

2013 ◽  
Vol 85 (4) ◽  
pp. 1427-1438 ◽  
Author(s):  
MATHIAS A. CHIA ◽  
ANA T. LOMBARDI ◽  
MARIA DA GRACA G. MELAO
Keyword(s):  
Biomass Production ◽  
Chlorella Vulgaris ◽  
Biochemical Composition ◽  
Physiological Response ◽  
Low Cost ◽  
Cost Effective ◽  
Growth Conditions ◽  
Growth Media ◽  
Continuous Cultures ◽  
The Cost

The need for clean and low-cost algae production demands for investigations on algal physiological response under different growth conditions. In this research, we investigated the growth, biomass production and biochemical composition of Chlorella vulgaris using semi-continuous cultures employing three growth media (LC Oligo, Chu 10 and WC media). The highest cell density was obtained in LC Oligo, while the lowest in Chu medium. Chlorophyll a, carbohydrate and protein concentrations and yield were highest in Chu and LC Oligo media. Lipid class analysis showed that hydrocarbons (HC), sterol esthers (SE), free fatty acids (FFA), aliphatic alcohols (ALC), acetone mobile polar lipids (AMPL) and phospholipids (PL) concentrations and yields were highest in the Chu medium. Triglyceride (TAG) and sterol (ST) concentrations were highest in the LC Oligo medium. The results suggested that for cost effective cultivation, LC Oligo medium is the best choice among those studied, as it saved the cost of buying vitamins and EDTA associated with the other growth media, while at the same time resulted in the best growth performance and biomass production.

THEORETICAL ANALYSES FOR LASER MACHINING MICROCHANNELS AND DEMONSTRATION OF THEIR USES IN MANUFACTURE OF A MICROFLUIDIC OPTICAL SWITCH

2006 ◽  
Vol 13 (06) ◽  
pp. 795-802 ◽  
Author(s):  
DANIEL LIM ◽  
ERNA GONDO SANTOSO ◽  
KIM MING TEH ◽  
STEPHEN WAN ◽  
H. Y. ZHENG
Keyword(s):  
Fluid Flow ◽  
Optical Switch ◽  
Low Cost ◽  
Microfluidic Devices ◽  
Cost Effective ◽  
Laser Machining ◽  
Machining Parameters ◽  
Flow Channels ◽  
Cost Effective Method ◽  
Theoretical Analyses

Silicon has been widely used to fabricate microfluidic devices due to the dominance of silicon microfabrication technologies available. In this paper, theoretical analyses are carried out to suggest suitable laser machining parameters to achieve required channel geometries. Based on the analyses, a low-power CO 2 laser was employed to create microchannels in Acrylic substrate for the use of manufacturing an optical bubble switch. The developed equations are found useful for selecting appropriate machining parameters. The ability to use a low-cost CO 2 laser to fabricate microchannels provides an alternative and cost-effective method for prototyping fluid flow channels, chambers and cavities in microfluidic lab chips.

scholarly journals Synchronous fluorescence as a green and selective tool for simultaneous determination of bambuterol and its main degradation product, terbutaline

2018 ◽  
Vol 5 (10) ◽  
pp. 181359 ◽  
Author(s):  
Samah Abo El Abass ◽  
Heba Elmansi
Keyword(s):  
Degradation Product ◽  
Low Cost ◽  
Reference Method ◽  
Cost Effective ◽  
Zero Crossing ◽  
Cost Effective Method ◽  
Validation Parameters ◽  
Main Degradation Product ◽  
20 Nm

A green, sensitive and cost-effective method is introduced in this research for the determination of bambuterol and its main degradation product, terbutaline, simultaneously, relying on the synchronous spectrofluorimetric technique. First derivative synchronous spectrofluorimetric amplitude is measured at Δ λ = 20 nm, so bambuterol can be quantitated at 260 nm, and terbutaline can be measured at 290 nm, each at the zero crossing point of the other. The amplitude–concentration plots were linear over the concentration ranges of 0.2–6.0 µg ml −1 and 0.2–4.0 µg ml −1 for both bambuterol and terbutaline, respectively. Official guidelines were followed to calculate the validation parameters of the proposed method. The low values of limits of detection of 0.023, 0.056 µg ml −1 and limits of quantitation of 0.071, 0.169 µg ml −1 for bambuterol and terbutaline, respectively, point to the sensitivity of the method. Bambuterol is a prodrug for terbutaline, and the latter is considered its degradation product so the established method could be regarded as a stability-indicating one. Moreover, the proposed method was used for the analysis of bambuterol and terbutaline in their single ingredient preparations and the results revealed statistical agreement with the reference method. The suggested method, being a simple and low-cost procedure, is superior to the previously published methods which need more sophisticated techniques, longer analysis time and highly toxic solvents and reagents. It could be considered as an eco-friendly analytical procedure.

scholarly journals Protection of computers from side electromagnetic radiation during monitor images formation

2021 ◽  
Vol 4 (4) ◽  
pp. 377-385
Author(s):  
Volodymyr M. Lucenko ◽  
Dmytro O. Progonov
Keyword(s):  
Electromagnetic Radiation ◽  
Ad Hoc ◽  
Low Cost ◽  
Cost Effective ◽  
Switching Speed ◽  
Cost Effective Approach ◽  
Alternative Approach ◽  
Confidential Data ◽  
The Cost ◽  
Communication Lines

Reliable protection of confidential data processed in critical information infrastructure elements of public institutions and private organizations is topical task today. Of particular interest are methods to prevent the leakage of confidential data by localizing informative (dangerous) signals that both carry an informative component, and have a signal level higher than predefined threshold. The increase in signal energy from personal computers is caused by increasing of its transistors switching speed. Modern passive shielding methods for secured computers, similar to the well-known program TEMPEST, require either costly and large shielding units or technological simplification by using of low-cost fragmentary shielding of computer’s individual elements. Therefore, localization of side electromagnetic radiation produced by personal computer is needed. The paper presents a cost-effective approach to reducing the level of computer’s electromagnetic radiation by passive method. The radiation are localized and measured by its estimation on personal computer’s elements, namely unshielded communication lines between video processor and a monitor, fragments of electric tracks on motherboards, etc. During experiments authors used ad-hoc miniature electric (ball antenna) and magnetic (Hall sensor) antennas connected to selective voltmeters. This approach significantly reduces the cost of equipment and measurements as well as requirements to analytics’ qualification for improving computer’s protection. Also, the alternative approach for computer protection is proposed. The approach is based on image content protection by distorting the image on the monitor instead of reducing electromagnetic radiation caused by signals from the monitor. The protection includes image scrambling using Arnold transform that randomly “shuffle” the lines in each frame.

Method of Fuels and Lubricants Performance Properties Requirements Management

2021 ◽  
Vol 624 (2) ◽  
pp. 16-24
Author(s):  
Yu. M. Pimenov ◽  
◽  
A. V. Ulit’ko ◽  
V. A. Sereda ◽  
◽  
...  
Keyword(s):  
Cost Effective ◽  
Life Cycles ◽  
Requirements Management ◽  
Performance Properties ◽  
Operational Conditions ◽  
Quantitative Expression ◽  
Laboratory Bench ◽  
Motor Fuels ◽  
Cost Effective Method ◽  
The Cost

The cost-effective method of fuels and lubricants performance properties requirements management is proposed. Method ensures effectiveness enhancement of equipment and of fuels and lubricants life cycles; it includes requirements establishment (constructing of conceptual and empirical models of requirements), their quantitative expression through highly informative indicators of fuels and lubricants propensity for transformations, then approbation with the use of laboratory, bench and test stands tests, specification, assessment of realization in real world equipment operational conditions, effectiveness evaluation and modification of requirements. Some illustrations of application of the new method phases with regards to motor fuels and hydraulic fluid are provided.

An Active Low Cost Mesh Networking Indoor Tracking System

2014 ◽  
Vol 6 (1) ◽  
pp. 45-79 ◽  
Author(s):  
Sean Carlin ◽  
Kevin Curran
Keyword(s):  
Tracking System ◽  
Low Cost ◽  
Cost Effective ◽  
Limiting Factors ◽  
Unique Contribution ◽  
Scalable Vector Graphics ◽  
Web Technologies ◽  
Working Environments ◽  
System A ◽  
The Cost

Indoor radio frequency tracking systems are generally quite expensive and can vary in accuracy due to interference, equipment quality or other environmental factors. Due to these limiting factors of the technology, many businesses today find it hard to justify investing in RFID tracking technologies to improve the safety, efficiency and security of their working environments. The aim of this project was to provide a budget RFID tracking system that was capable of tracking a person or object through an indoor environment. To minimize the cost of the RFID tracking system, the components of the system were built from existing electronic equipment and hardware. The software was also written to minimize licensing and support fees allowing a cost effective budget RFID tracking system to be developed. The tracking system consists of a tag, reader nodes and a PC reader which utilize synapse RF 100 engines with python scripts embedded on to the chips. The tracking system software operates through a web portal utilizing web technologies such as HTML, JavaScript and PHP to allow the tags location to be represented on a two dimensional map using scalable vector graphics. During development of the system a new trilateration algorithm was developed and used convert the signals received from the tag to a virtual position on the map correlating to the actual physical position of the tag. A unique contribution of this system is the low cost of building which we estimate as less than £200 UK sterling for a five node system.

Joining Dissimilar Materials Using Friction Stir Scribe Technique

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Piyush Upadhyay ◽  
Yuri Hovanski ◽  
Saumyadeep Jana ◽  
Leonard S. Fifield
Keyword(s):  
Low Cost ◽  
Dissimilar Materials ◽  
Cost Effective ◽  
High Volume ◽  
Industrial Applications ◽  
Critical Pathway ◽  
Friction Stir ◽  
Design Engineers ◽  
Cost Effective Method ◽  
Polymer Metal

Development of a robust and cost-effective method of joining dissimilar materials could provide a critical pathway to enable widespread use of multimaterial designs and components in mainstream industrial applications. The use of multimaterial components such as steel-aluminum and aluminum-polymer would allow design engineers to optimize material utilization based on service requirements and could often lead to weight and cost reductions. However, producing an effective joint between materials with vastly different thermal, microstructural, and deformation responses is highly problematic using conventional joining and/or fastening methods. This is especially challenging in cost sensitive, high volume markets that largely rely on low cost joining solutions. Friction stir scribe (FSS) technology was developed to meet the demands of joining materials with drastically different properties and melting regimes. The process enables joining of light metals like magnesium and aluminum to high temperature materials like steel and titanium. Viable joints between polymer composites and metal can also be made using this method. This paper will present the state of the art, progress made, and challenges associated with this innovative derivative of friction stir welding (FSW) in reference to joining dissimilar metals and polymer/metal combinations.

scholarly journals Self-managed, computerised word finding therapy as an add-on to usual care for chronic aphasia post-stroke: An economic evaluation

2020 ◽  
pp. 026921552097534
Author(s):  
Nicholas R Latimer ◽  
Arjun Bhadhuri ◽  
Abu O Alshreef ◽  
Rebecca Palmer ◽  
Elizabeth Cross ◽  
...  
Keyword(s):  
Cost Effectiveness ◽  
Usual Care ◽  
Low Cost ◽  
Controlled Trial ◽  
Life Time ◽  
Cost Effective ◽  
Quality Adjusted Life Year ◽  
Post Stroke ◽  
Word Finding ◽  
The Cost

Objective: To examine the cost-effectiveness of self-managed computerised word finding therapy as an add-on to usual care for people with aphasia post-stroke. Design: Cost-effectiveness modelling over a life-time period, taking a UK National Health Service (NHS) and personal social service perspective. Setting: Based on the Big CACTUS randomised controlled trial, conducted in 21 UK NHS speech and language therapy departments. Participants: Big CACTUS included 278 people with long-standing aphasia post-stroke. Interventions: Computerised word finding therapy plus usual care; usual care alone; usual care plus attention control. Main measures: Incremental cost-effectiveness ratios (ICER) were calculated, comparing the cost per quality adjusted life year (QALY) gained for each intervention. Credible intervals (CrI) for costs and QALYs, and probabilities of cost-effectiveness, were obtained using probabilistic sensitivity analysis. Subgroup and scenario analyses investigated cost-effectiveness in different subsets of the population, and the sensitivity of results to key model inputs. Results: Adding computerised word finding therapy to usual care had an ICER of £42,686 per QALY gained compared with usual care alone (incremental QALY gain: 0.02 per patient (95% CrI: −0.05 to 0.10); incremental costs: £732.73 per patient (95% CrI: £674.23 to £798.05)). ICERs for subgroups with mild or moderate word finding difficulties were £22,371 and £21,262 per QALY gained respectively. Conclusion: Computerised word finding therapy represents a low cost add-on to usual care, but QALY gains and estimates of cost-effectiveness are uncertain. Computerised therapy is more likely to be cost-effective for people with mild or moderate, as opposed to severe, word finding difficulties.

Sign in / Sign up

Export Citation Format

Share Document