Influences of electroosmosis and electrophoresis on permeate flux and membrane fouling in submerged membrane bioreactors (SMBRs)

2016 ◽  
Vol 74 (3) ◽  
pp. 766-776 ◽  
Author(s):  
Secil Bayar ◽  
Ahmet Karagunduz ◽  
Bulent Keskinler
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Membrane Bioreactors ◽  
Polymeric Membrane ◽  
Soluble Microbial Products ◽  
Permeate Flux ◽  
Electrical Field ◽  
Cake Layer ◽  
Significant Process ◽  
Microbial Products

The objective of this study was to investigate the influences of electroosmosis (EO) and electrophoresis (EP) on the permeate flux in submerged membrane bioreactors. When a polymeric membrane is placed in between an anode and a cathode, both EO and EP occur simultaneously, causing enhancement in flux. Results showed that after 150 min of filtration, the permeate fluxes were 60, 115, 175 and 260 L/m2/h at 0, 30, 40 and 50 V, respectively. It was shown that the EO was linearly changing with increasing voltage, reaching up to 54 L/m2/h at 50 V. EP was found to be a significant process in removing soluble microbial products from the membrane surface, resulting in an increase in permeate flux as the filtration progressed. About 20-fold of smaller protein and carbohydrate concentrations were found in the cake layer when the electrical field (EF) was applied. However, the EF application promoted pore fouling, because of the calcium and magnesium scaling.

scholarly journals Numerical simulation of filtration performance in submerged membrane bioreactors: effect of particle packed structure

2017 ◽  
Vol 76 (9) ◽  
pp. 2503-2514 ◽  
Author(s):  
Zhidong Wang ◽  
Kuizu Su ◽  
Tong Shu ◽  
Weihong Wang
Keyword(s):  
Membrane Surface ◽  
Membrane Bioreactors ◽  
Navier Stokes ◽  
Permeate Flux ◽  
The Finite Element Method ◽  
Brinkman Equations ◽  
Filtration Performance ◽  
Cake Layer ◽  
Packed Structure ◽  
Cake Porosity

Abstract It is widely known that the accumulation of solid matter forming a cake layer on the membrane surface is one of the major limitations of the filtration performance in submerged membrane bioreactors (SMBR). This study is focused on the influence of the cake porosity of different particle microscopic packed structures on the filtration performance of hollow fiber systems. An integrated model based on the finite element method to simulate numerically the flow in an SMBR is presented. The model coupled the Navier–Stokes and Darcy Brinkman equations to simulate a complete filtration run. The cake growth took into consideration not only the deposition with local filtration velocity but also the effect of aeration scouring. A novel solution of mesh deformation was adopted to investigate transient cake growth along the fiber. Comparisons between simulations and experiments are in good agreement. The results show that a higher porosity particle packed structure causes non-uniform filtration and cake thickness but also higher permeate flux. Meanwhile, the proportion of cake resistance to total resistance increases with the decrease of porosity.

Fouling cake layer in a submerged anaerobic membrane bioreactor treating saline wastewaters: curse or a blessing?

2011 ◽  
Vol 63 (12) ◽  
pp. 2902-2908 ◽  
Author(s):  
I. Vyrides ◽  
D. C. Stuckey
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Large Fraction ◽  
Membrane Bioreactors ◽  
Extracellular Polysaccharides ◽  
Cake Layer ◽  
Anaerobic Membrane Bioreactors ◽  
Suspended Biomass ◽  
Microbial Products

The treatment of inhibitory (saline) wastewaters is known to produce considerable amounts of soluble microbial products (SMPs), and this has been implicated in membrane fouling; the fate of these SMPs was of considerable interest in this work. This study also investigated the contribution of SMPs to membrane fouling of the; (a) cake layer/biofilm layer, (b) the compounds below the biofilm/cake layer and strongly attached to the surface of the membrane, (c) the compounds in the inner pores of the membrane, and (d) the membrane. It was found that the cake/biofilm layer was the main reason for fouling of the membrane. Interestingly, the bacteria attached to the cake/biofilm layer showed higher biodegradation rates compared with the bacteria in suspension. Moreover, the bacteria attached to the cake layer showed higher amounts of attached extracellular polysaccharides (EPS) compared with the bacteria in suspension, possibly due to accumulation of the released EPS from suspended biomass in the cake/biofilm layer. Molecular weight (MW) analysis of the effluent and reactor bulk showed that the cake layer can retain a large fraction of the SMPs in the reactor and prevent them from being released into the effluent. Hence, while cake layers lead to lower fluxes in submerged anaerobic membrane bioreactors (SAMBRs), and hence higher costs, they can improve the quality of the reactor effluent.

scholarly journals Biomass Characteristics and Their Effect on Membrane Bioreactor Fouling

Molecules ◽  
2019 ◽  
Vol 24 (16) ◽  
pp. 2867 ◽  
Author(s):  
Petros K. Gkotsis ◽  
Anastasios I. Zouboulis
Keyword(s):  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Suspended Solids ◽  
Extracellular Polymeric Substances ◽  
Membrane Surface ◽  
Membrane Resistance ◽  
Soluble Microbial Products ◽  
Gelling Properties ◽  
Microbial Products ◽  
Soluble Part

Biomass characteristics are regarded as particularly influential for fouling in Membrane Bio-Reactors (MBRs). They primarily include the Mixed Liquor Suspended Solids (MLSS), the colloids and the Extracellular Polymeric Substances (EPS). Among them, the soluble part of EPS, which is also known as Soluble Microbial Products (SMP), is the most significant foulant, i.e., it is principally responsible for membrane fouling and affects all fundamental fouling indices, such as the Trans-Membrane Pressure (TMP) and the membrane resistance and permeability. Recent research in the field of MBRs, tends to consider the carbohydrate fraction of SMP (SMPc) the most important characteristic for fouling, mainly due to the hydrophilic and gelling properties, which are exhibited by polysaccharides and allow them to be easily attached on the membrane surface. Other wastewater and biomass characteristics, which affect indirectly membrane fouling, include temperature, viscosity, dissolved oxygen (DO), foaming, hydrophobicity and surface charge. The main methods employed for the characterization and assessment of biomass quality, in terms of filterability and fouling potential, can be divided into direct (such as FDT, SFI, TTF100, MFI, DFCM) or indirect (such as CST, TOC, PSA, RH) methods, and they are shortly presented in this review.

scholarly journals Performance of an indigenous integrated slurry photocatalytic membrane reactor (PMR) on the removal of aqueous phenanthrene (PHE)

2018 ◽  
Vol 77 (11) ◽  
pp. 2642-2656 ◽  
Author(s):  
C. Nirmala Rani ◽  
S. Karthikeyan
Keyword(s):  
Membrane Fouling ◽  
Membrane Reactor ◽  
Membrane Surface ◽  
Continuous Process ◽  
Permeate Flux ◽  
Toc Removal ◽  
Recovery Potential ◽  
Cake Layer ◽  
Alkaline Conditions ◽  
Photocatalytic Membrane Reactor

Abstract In this study, a slurry photocatalytic membrane reactor (PMR) was developed and evaluated for the degradation of aqueous phenanthrene (PHE). During continuous process with a hydraulic retention time (HRT) of 140 min, the maximum PHE degradation and total organic carbon (TOC) removal efficiencies were found to be 97% and 79%, respectively. The reuse and recovery potential of TiO2 was studied with continuous recycling. The major intermediates during photodegradation of PHE were found to be phenanthrenequinone, phenanthenol and fluorine. This study also includes an investigation of membrane fouling caused by hydrophilic nano TiO2. The cake layer observed on the membrane surface was characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive spectroscopy (EDS). In addition, the effect of operating parameters such as pH and permeate flux on membrane fouling were also investigated. Low permeate flux and alkaline conditions reduced membrane fouling.

scholarly journals Studies of polypropylene membrane fouling during microfiltration of broth with Citrobacter freundii bacteria

2015 ◽  
Vol 17 (4) ◽  
pp. 56-64 ◽  
Author(s):  
Marek Gryta ◽  
Marta Waszak ◽  
Maria Tomaszewska
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Transmembrane Pressure ◽  
Citrobacter Freundii ◽  
Permeate Flux ◽  
Process Duration ◽  
Polypropylene Membrane ◽  
Flux Decline ◽  
Cake Layer ◽  
Scanning Electron

Abstract In this work a fouling study of polypropylene membranes used for microfiltration of glycerol solutions fermented by Citrobacter freundii bacteria was presented. The permeate free of C. freundii bacteria and having a turbidity in the range of 0.72–1.46 NTU was obtained. However, the initial permeate flux (100–110 L/m2h at 30 kPa of transmembrane pressure) was decreased 3–5 fold during 2–3 h of process duration. The performed scanning electron microscope observations confirmed that the filtered bacteria and suspensions present in the broth formed a cake layer on the membrane surface. A method of periodical module rinsing was used for restriction of the fouling influence on a flux decline. Rinsing with water removed most of the bacteria from the membrane surface, but did not permit to restore the initial permeate flux. It was confirmed that the irreversible fouling was dominated during broth filtration. The formed deposit was removed using a 1 wt% solution of sodium hydroxide as a rinsing solution.

scholarly journals Combined Effect of Colloids and SMP on Membrane Fouling in MBRs

Membranes ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 118 ◽  
Author(s):  
Dimitra Banti ◽  
Manassis Mitrakas ◽  
Georgios Fytianos ◽  
Alexandra Tsali ◽  
Petros Samaras
Keyword(s):  
Membrane Fouling ◽  
Oxygen Demand ◽  
Membrane Bioreactors ◽  
Combined Effect ◽  
Transmembrane Pressure ◽  
Soluble Microbial Products ◽  
Treatment Efficiency ◽  
Membrane Pore ◽  
Microbial Products ◽  
Membrane Pore Size

Membrane fouling investigations in membrane bioreactors (MBRs) are a top research issue. The aim of this work is to study the combined effect of colloids and soluble microbial products (SMPs) on membrane fouling. Two lab-pilot MBRs were investigated for treating two types of wastewater (wwt), synthetic and domestic. Transmembrane pressure (TMP), SMP, particle size distribution and treatment efficiency were evaluated. Chemical Oxygen Demand (COD) removal and nitrification were successful for both kinds of sewage reaching up to 95–97% and 100%, respectively. Domestic wwt presented 5.5 times more SMP proteins and 11 times more SMP carbohydrates compared to the synthetic one. In contrast, synthetic wwt had around 20% more colloids in the mixed liquor with a size lower than membrane pore size (<400 nm) than domestic. Finally, the TMP at 36 days reached 16 kPa for synthetic wwt and 11 kPa for domestic. Therefore, synthetic wwt, despite its low concentration of SMPs, caused severe membrane fouling compared to domestic, a result that is attributed to the increased concentration of colloids. Consequently, the quantity of colloids and possibly their special characteristics play decisive and more important roles in membrane fouling compared to the SMP—a novel conclusion that can be used to mitigate membranes fouling.

Deposit membrane fouling: influence of specific cake layer resistance and tangential shear stresses

2014 ◽  
Vol 70 (1) ◽  
pp. 40-46 ◽  
Author(s):  
A. Charfi ◽  
J. Harmand ◽  
N. Ben Amar ◽  
A. Grasmick ◽  
M. Heran
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Suspended Solid ◽  
Shear Stresses ◽  
Permeate Flux ◽  
Recirculation Flow ◽  
Resistance Evolution ◽  
Cake Layer ◽  
Macro Scale ◽  
The Difference

Cake fouling is the leading cause of membrane permeability decrease when filtering mixed liquor suspension containing high suspended solid concentrations. A simple model is proposed to simulate the cake resistance evolution with time by considering a macro-scale fouling linked only to the accumulation of particles on the membrane surface. This accumulation appears as the difference between the flux of deposited particles due to the filtration and the flux of particles detached from the membrane surface due to the tangential shear stresses caused by recirculation flow in the sidestream membrane bioreactor (MBR) or gas sparging close to the membrane surface for submerged MBR configuration. Two determining parameters were then highlighted: the specific cake resistance and the ‘shear parameter’. Based on these parameters it is possible to predict model outputs as cake resistance and permeate flux evolution for short-time filtration periods.

Electroflocculation as potential pretreatment in colloid ultrafiltration

2006 ◽  
Vol 6 (1) ◽  
pp. 69-78 ◽  
Author(s):  
T. Harif ◽  
M. Hai ◽  
A. Adin
Keyword(s):  
Membrane Fouling ◽  
Colloidal Suspension ◽  
Membrane Surface ◽  
Constant Current ◽  
Permeate Flux ◽  
Batch Mode ◽  
Membrane Behavior ◽  
Flux Decline ◽  
Stainless Steel Cathode ◽  
Marginal Improvement

Electroflocculation (EF) is a coagulation/flocculation process in which active coagulant species are generated in situ by electrolytic oxidation of an appropriate anode material. The effect of colloidal suspension pretreatment by EF on membrane fouling was measured by flux decline at constant pressure. An EF cell was operated in batch mode and comprised two flat sheet electrodes, an aluminium anode and stainless steel cathode, which were immersed in the treated suspension, and connected to an external DC power supply. The cell was run at constant current between 0.06–0.2A. The results show that pre-EF enhances the permeate flux at pH 5 and 6.5, but only marginal improvement is observed at pH 8. At all pH values cake formation on the membrane surface was observed. The differences in membrane behavior can be explained by conventional coagulation theory and transitions between aluminium mononuclear species which affect particle characteristics and consequently cake properties. At pH 6.5, where sweep floc mechanism dominates due to increased precipitation of aluminium hydroxide, increased flux rates were observed. It is evident that EF can serve as an efficient pretreatment to ultrafiltration of colloid particles.

Sign in / Sign up

Export Citation Format

Share Document