Comparison between Brazilian agro-wastes and activated carbon as adsorbents to remove Ni(II) from aqueous solutions

2016 ◽  
Vol 73 (11) ◽  
pp. 2713-2721 ◽  
Author(s):  
Guilherme Luiz Dotto ◽  
Lucas Meili ◽  
Ana Karla de Souza Abud ◽  
Eduardo Hiromitsu Tanabe ◽  
Daniel Assumpção Bertuol ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Low Cost ◽  
Orange Peel ◽  
Point Of Zero Charge ◽  
Equilibrium Studies ◽  
Factors Affecting ◽  
Op Amp ◽  
Batch Tests ◽  
Pineapple Peel ◽  
Equilibrium Data

This research was performed to find an alternative, low-cost, competitive, locally available and efficient adsorbent to treat nickel (Ni) containing effluents. For this purpose, several Brazilian agro-wastes like sugarcane bagasse (SCB), passion fruit wastes (PFW), orange peel (OP) and pineapple peel (PP) were compared with an activated carbon (AC). The adsorbents were characterized. Effects of fundamental factors affecting the adsorption were investigated using batch tests. Kinetic and equilibrium studies were performed using conventional models. It was verified that the adsorption was favored at pH of 6.0 for all agro-wastes, being dependent of the Ni speciation, point of zero charge and surface area of the adsorbents. The Ni removal percentage was in the following order: SCB > OP > AC > PFW > PP. From the kinetic viewpoint, the Elovich model was appropriate to fit the Ni adsorption onto SCB, while for the other adsorbents, the pseudo-first-order model was the most suitable. For all adsorbents, the Langmuir model was the more adequate to represent the equilibrium data, being the maximum adsorption capacities of 64.1 mg g−1, 60.7 mg g−1, 63.1 mg g−1, 48.1 mg g−1 and 64.3 mg g−1 for SCB, PFW, OP, PP and AC, respectively. These results indicated that mainly SCB and OP can be used as alternative adsorbents to treat Ni containing effluents.

scholarly journals Methylene blue removal using a low-cost activated carbon adsorbent from tobacco stems: kinetic and equilibrium studies

2017 ◽  
Vol 75 (10) ◽  
pp. 2390-2402 ◽  
Author(s):  
Bellington Mudyawabikwa ◽  
Henry H. Mungondori ◽  
Lilian Tichagwa ◽  
David M. Katwire
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Radiation Power ◽  
Low Cost ◽  
Carbon Adsorbent ◽  
Point Of Zero Charge ◽  
Order Kinetic ◽  
Optimum Conditions ◽  
Equilibrium Studies ◽  
Mb Adsorption

The aim of this study was to prepare activated carbon from tobacco stalks using microwave heating. The prepared activated carbon was applied as an adsorbent in methylene blue (MB) removal from water. The optimum conditions for activated carbon preparation were a radiation power of 280 W for a period of 6 minutes after the impregnation of the precursor material with 30% ZnCl2 for 24 hours. The activated carbon yield and iodine number were 49.43% and 1,264.51 mg/g respectively. The activated carbon also had a point of zero charge of 5.81 with an adsorption capacity of 123.45 mg/g for MB. The optimum conditions for MB adsorption were a pH of 6.5 with an adsorbent dosage of 0.2 g/50 mL at 25 °C. The MB adsorption kinetics followed the pseudo second order kinetic model with the intra-particle diffusion model suggesting a two-step adsorption mechanism. The adsorption data also fitted well within the Langmuir adsorption isotherm model. Tobacco stalks can successfully be turned into an economically important product.

Adsorptive Removal of Pb(II) Ion from Aqueous Solution Using Rice Husk-Based Activated Carbon

2014 ◽  
Vol 875-877 ◽  
pp. 196-201 ◽  
Author(s):  
Mohd Faisal Taha ◽  
Ahmad S. Rosman ◽  
Maizatul S. Shaharun
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Rice Husk ◽  
Low Cost ◽  
Chemical Activation ◽  
Textural Properties ◽  
Activation Process ◽  
Adsorption Studies ◽  
Three Samples ◽  
Equilibrium Data

The potential of rice husk-based activated carbon as an alternative low-cost adsorbent for the removal of Pb (II) ion from aqueous solution was investigated. Rice husk-based activated carbon was preparedviachemical activation process using NaOH followed by the carbonization process at 500°C. Morphological analysis was conducted using field-emission scanning electron microscope /energy dispersive X-ray (FESEM/EDX) on three samples, i.e. raw rice husk, rice husk treated with NaOH and rice husk-based activated carbon. These three samples were also analyzed for their C, H, N, O and Si contents using CHN elemental analyzer and FESEM/EDX. The textural properties of rice husk-based activated carbon, i.e. surface area (253 m2/g) and pore volume (0.17 cm2/g), were determined by N2adsorption. The adsorption studies using rice husk-based activated carbon as an adsorbent to remove Pb (II) ion from aqueous solution were carried out at a fixed initial concentration of Pb (II) ion (150 ppm) with varying adsorbent dose as a function of contact time at room temperature. The concentration of Pb (II) ion was determined by atomic absorption spectrophotometer (AAS). The removal of Pb (II) ion from aqueous solution increased from 35 % to 82 % when the amount of rice husk-based activated carbon was increased from 0.05 g to 0.30 g. The equilibrium data obtained from adsorption studies was found to fit both Langmuir and Freundlich adsorption isotherms.

scholarly journals Studies on Removal of Cr (VI) from Aqueous Solutions Using Powder of Mosambi Fruit Peelings (PMFP) As a Low Cost Sorbent

2012 ◽  
Vol 9 (3) ◽  
pp. 1389-1399 ◽  
Author(s):  
R. Hema Krishna ◽  
A. V. V. S. Swamy
Keyword(s):  
Particle Size ◽  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Batch Tests ◽  
Freundlich Adsorption Isotherm ◽  
Equilibrium Data ◽  
Agitation Time

The powder of mosambi fruit peelings (PMFP) was used as an adsorbent for the removal of heavy metal like Cr (VI) from aqueous solutions was studied using batch tests. The influence of physico-chemical key parameters such as the initial metal ion concentration, pH, agitation time, adsorbent dosage, and the particle size of adsorbent has been considered in batch tests. Sorbent ability to adsorb Cr (VI) ions was examined and the mechanism involved in the process investigated. The optimum results were determined at an initial metal ion concentration was 10 mg/lit, pH=2, agitation time – 60 min, an adsorbent dose (150 mg/50 ml) and the particle size (0.6 mm). The % adsorption, Langmuir constants [Q0=7.51(mg/g) and b=1.69(mg/lit)] Freundlich constant(Kf=2.94), Lagergren rate constants (Kad(min-1)=5.75 x 10-2) for [Cr(VI)] 10 mg/lit were determined for the adsorption system as a function of sorbate concentration. The equilibrium data obtained were tested using Langmuir, Freundlich adsorption isotherm models, and the kinetic data obtained were fitted to pseudo first order model.

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

scholarly journals Comparison of Surface and Structural Properties of Carbonaceous Materials Prepared by Chemical Activation of Tomato Paste Waste: The Effects of Activator Type and Impregnation Ratio

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Nurgul Ozbay ◽  
Adife Seyda Yargic
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Activation Process ◽  
X Ray ◽  
Tomato Paste

Activated carbons were prepared by carbonization of tomato paste processing industry waste at 500°C followed by chemical activation with KOH, K2CO3, and HCl in N2 atmosphere at low temperature (500°C). The effects of different activating agents and impregnation ratios (25, 50, and 100 wt.%) on the materials’ characteristics were examined. Precursor, carbonized tomato waste (CTW), and activated carbons were characterized by using ultimate and proximate analysis, thermogravimetric analysis (TG/DTG), Fourier transform-infrared (FT-IR) spectroscopy, X-ray fluorescence (XRF) spectroscopy, point of zero charge measurements (pHPZC), particle size analyzer, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, nitrogen adsorption/desorption isotherms, and X-ray diffraction (XRD) analysis. Activation process improved pore formation and changed activated carbons’ surface characteristics. Activated carbon with the highest surface area (283 m3/g) was prepared by using 50 wt.% KOH as an activator. According to the experimental results, tomato paste waste could be used as an alternative precursor to produce low-cost activated carbon.

scholarly journals Preparation and characterization of activated carbon from Amygdalus Scoparia shell by chemical activation and its application for removal of lead from aqueous solutions

2010 ◽  
Vol 8 (6) ◽  
pp. 1273-1280 ◽  
Author(s):  
Sayed Mohammadi ◽  
Mohammad Karimi ◽  
Daryoush Afzali ◽  
Fatemeh Mansouri
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Low Cost ◽  
Chemical Activation ◽  
Maximum Adsorption Capacity ◽  
Batch Tests ◽  
Amygdalus Scoparia ◽  
Langmuir And Freundlich Equations ◽  
Characterization Of Activated Carbon

AbstractTwo series of activated carbon have been prepared by chemical activation of Amygdalus Scoparia shell with phosphoric acid or zinc chloride for the removal of Pb(II) ions from aqueous solutions. Several methods were employed to characterize the active carbon produced. The surface area was calculated using the standard Brunauer-Emmet-Teller method. The microstructures of the resultant activated carbon were observed by scanning electron microscopy. The chemical composition of the surface resultant activated carbon was determined by Fourier transform infrared spectroscopy. In the batch tests, the effect of pH, initial concentration, and contact time on the adsorption were studied. The data were fitted with Langmuir and Freundlich equations to describe the equilibrium isotherms. The maximum adsorption capacity of Pb(II) on the resultant activated carbon was 36.63 mg g−1 with H3PO4 and 28.74 mg g−1 with ZnCl2. To regenerate the spent adsorbents, desorption experiments were performed using 0.25 mol L−1 HCl. Here we propose that the activated carbon produced from Amygdalus Scoparia shell is an alternative low-cost adsorbent for Pb(II) adsorption.

Characterization of the Corallina Elongata Alga and Study of its Biosorption Properties for Methylene Blue

2019 ◽  
Vol 41 (1) ◽  
pp. 62-62
Author(s):  
Farida Bouremmad Farida Bouremmad ◽  
Abdennour Bouchair Abdennour Bouchair ◽  
Sorour Semsari Parapari Sorour Semsari Parapari ◽  
Shalima Shawuti and Mehmet Ali Gulgun Shalima Shawuti and Mehmet Ali Gulgun
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Mediterranean Coast ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Aquatic Biomass ◽  
Equilibrium Data

Biosorbents can be an alternative to activated carbon. They are derived from agricultural by-products or aquatic biomass. They are low cost and they may have comparable performances to those of activated carbon. The present study focuses on the characterization of the Corallina Elongata (CE) alga and its adsorption performance for Methylene Blue (MB), this alga is found in abundance at the Mediterranean coast of the city of Jijel in eastern Algeria. The dried alga was characterized using various characterization techniques such as DTA, TG, FTIR, XRD, SEM and EDX, which showed that the material consists essentially of a calcite containing magnesium. Batch adsorption studies were carried out and the effect of experimental parameters Such as pH, initial dye concentration, temperature, adsorbent dose and contact time, on the adsorption of MB was studied. The kinetic experimental data were found to conform to the pseudo-second-order model with good correlation and equilibrium data were best fitted to The Langmuir model, with a maximum adsorption capacity of 34.4 mg/g. The adsorption isotherms at various temperatures allowed the determination of certain thermodynamic parameters (ΔG, ΔH and ΔS). Finally, the adsorption results showed a good affinity between CE and MB with a high adsorption capacity.

Sign in / Sign up

Export Citation Format

Share Document