Enhanced removal of nitrate from water using nZVI@MWCNTs composite: synthesis, kinetics and mechanism of reduction

2015 ◽  
Vol 72 (11) ◽  
pp. 1988-1999 ◽  
Author(s):  
Ali Akbar Babaei ◽  
Ali Azari ◽  
Roshanak Rezaei Kalantary ◽  
Babak Kakavandi
Keyword(s):  
Nitrate Reduction ◽  
Nitrate Removal ◽  
Nitrogen Gas ◽  
Initial Concentration ◽  
Multi Wall Carbon Nanotubes ◽  
Batch System ◽  
Low Concentrations ◽  
End Products ◽  
Nano Zero Valent Iron ◽  
Influential Parameters

Herein, multi-wall carbon nanotubes (MWCNTs) were used as the carrier of nano-zero valent iron (nZVI) particles to fabricate a composite known as nZVI@MWCNTs. The composite was then characterized and applied in the nitrate removal process in a batch system under anoxic conditions. The influential parameters such as pH, various concentrations of nitrate and composite were investigated within 240 min of the reaction. The mechanism, kinetics and end-products of nitrate reduction were also evaluated. Results revealed that the removal nitrate percentage for nZVI@MWCNTs composite was higher than that of nZVI and MWCNTs alone. Experimental data from nitrate reduction were fitted to the Langmuir–Hinshelwood kinetic model. The values of observed rate constant (kobs) decreased with increasing the initial concentration of nitrate. Our experiments proved that the nitrate removal efficiency was favorable once both high amounts of nZVI@MWCNTs and low concentrations of nitrate were applied. The predominant end-products of the nitrate reduction were ammonium (84%) and nitrogen gas (15%). Our findings also revealed that ZVI@MWCNTs is potentially a good composite for removal/reduction of nitrate from aqueous solutions.

scholarly journals Preparation of Co/Ti electrode by electro-deposition for aqueous nitrate reduction

2021 ◽  
Author(s):  
Bicun Jiang ◽  
Liqin Han ◽  
Juntian Wang ◽  
Chang Lu ◽  
Yang Pan ◽  
...  
Keyword(s):  
Nitrate Reduction ◽  
Nitrate Removal ◽  
Ammonium Nitrogen ◽  
Nitrite Reduction ◽  
Electrolysis Cell ◽  
Ammonium Oxidation ◽  
Nitrogen Gas ◽  
Electro Deposition ◽  
Improved Stability ◽  
Chlorine Ion

Abstract A Co/Ti electrode for nitrate reduction was prepared by electrode-deposition. In the single-compartment electrolysis cell, nitrate (100 mg/L) removal reached nearly 100% after 3 h electrolysis under the current density of 20 mA cm–2 by using the Co/Ti electrode as cathode, and the main reduction products were ammonium nitrogen (66.5%) and nitrogen gas (33.5%). This performance on nitrate removal was comparable to a Co3O4/Ti electrode, and the electroactivity of the Co/Ti electrode towards nitrite reduction was higher than that of a Co3O4/Ti electrode. The Co/Ti electrode exhibited an improved stability with 18.7% of mass loss and 25.5% of Co dissolution compared with the Co3O4/Ti electrode after ultrasonic interference. The presence of chlorine ion (1,000 mg/L) could promote the total nitrogen (TN) removal to approximately 100% after 3 h electrolysis because of the ammonium oxidation by the free chlorine produced from the anode. In the presence of calcium (50 mg/L) and phosphate (0.5 mg/L), the nitrate removal decreased from 85.4 ± 1.5 to 57.7 ± 3.5% after ten reuse cycles. This result suggests that Ca and P should be pre-removed before the electro-reduction of nitrate.

Optimal operations for groundwater denitrification of drinking water using heterotrophic biological denitrification process

2006 ◽  
Vol 6 (2) ◽  
pp. 125-130
Author(s):  
C.-H. Hung ◽  
K.-H. Tsai ◽  
Y.-K. Su ◽  
C.-M. Liang ◽  
M.-H. Su ◽  
...  
Keyword(s):  
Drinking Water ◽  
Removal Efficiency ◽  
Nitrate Removal ◽  
Drinking Water Treatment ◽  
Nitrate Content ◽  
Source Water ◽  
Nitrogen Gas ◽  
Negative Effect ◽  
Denitrification Process ◽  
Heterotrophic Denitrification

Due to the extensive application of artificial nitrogen-based fertilizers on land, groundwater from the central part of Taiwan faces problems of increasing concentrations of nitrate, which were measured to be well above 30 mg/L all year round. For meeting the 10 mg/L nitrate standard, optimal operations for a heterotrophic denitrification pilot plant designed for drinking water treatment was investigated. Ethanol and phosphate were added for bacteria growing on anthracite to convert nitrate to nitrogen gas. Results showed that presence of high dissolved oxygen (around 4 mg/L) in the source water did not have a significantly negative effect on nitrogen removal. When operated under a C/N ratio of 1.88, which was recommended in the literature, nitrate removal efficiency was measured to be around 70%, sometimes up to 90%. However, the reactor often underwent severe clogging problems. When operated under C/N ratio of 1.0, denitrification efficiency decreased significantly to 30%. Finally, when operated under C/N ratio of 1.5, the nitrate content of the influent was almost completely reduced at the first one-third part of the bioreactor with an overall removal efficiency of 89–91%. Another advantage for operating with a C/N ratio of 1.5 is that only one-third of the biosolids was produced compared to a C/N value of 1.88.

scholarly journals The mechanism of in vitro clot lysis induced by vascular plasminogen activator

Blood ◽  
1984 ◽  
Vol 63 (6) ◽  
pp. 1331-1337 ◽  
Author(s):  
C Tran-Thang ◽  
EK Kruithof ◽  
F Bachmann
Keyword(s):  
Plasminogen Activator ◽  
Whole Blood ◽  
Apparent Molecular Weight ◽  
Clot Lysis ◽  
Initial Concentration ◽  
Low Concentrations ◽  
Sds Page ◽  
Tissue Plasminogen ◽  
Low Rate

Abstract The contribution of vascular plasminogen activator (v-PA) to the lysis of whole blood and plasma clots was investigated. v-PA released into the circulation after infusion of deamino-D-arginine vasopressin (DDAVP) was shown to bind quantitatively to plasma clots. Its apparent molecular weight, determined by the SDS-PAGE fibrin-agarose underlay method, was approximately 68,000 daltons, and its activity was quenched by antibodies against human tissue plasminogen activator (t-PA). Clots prepared from post-DDAVP plasma or post-DDAVP whole blood, rich in v- PA, did not lyse when incubated in imidazole buffer or normal plasma, as determined by the release of 125I from radiolabeled clots. However, clots made of v-PA-poor plasma or whole blood, incubated in v-PA-rich plasma, underwent substantial lysis. The concentration of PA in clots incubated in v-PA-rich plasma progressively increased in relation to the initial concentration of v-PA in the surrounding plasma. The results suggest that, at low concentrations of circulating v-PA, a hemostatic plug will lyse at a very low rate. However, when the v-PA concentration in the clot environment is increased, v-PA will accumulate progressively onto fibrin and induce thrombolysis.

scholarly journals Photocatalytic Degradation of Naphthalene By UV/Zno: Kinetics, Influencing Factors and Mechanisms

2021 ◽  
Vol 37 (1) ◽  
pp. 65-70
Author(s):  
Aram Dokht Khatibi ◽  
Kethineni Chandrika ◽  
Ferdos Kord Mostafapour ◽  
Ali Akbar Sajadi ◽  
Davoud Balarak
Keyword(s):  
Wastewater Treatment ◽  
Reaction Time ◽  
Aqueous Solutions ◽  
Aromatic Hydrocarbons ◽  
Contact Time ◽  
Initial Concentration ◽  
Applied Study ◽  
Batch System ◽  
Initial Ph ◽  
Conventional Wastewater Treatment

Conventional wastewater treatment is not able to effectively remove Aromatic hydrocarbons such as Naphthalene, so it is important to remove the remaining antibiotics from the environment. The aim of this study was to evaluate the efficiency of UV/ZnOphotocatalytic process in removing naphthalene antibiotics from aqueous solutions.This was an experimental-applied study that was performed in a batch system on a laboratory scale. The variables studied in this study include the initial pH of the solution, the dose of ZnO, reaction time and initial concentration of Naphthalene were examined. The amount of naphthalene in the samples was measured using GC.The results showed that by decreasing the pH and decreasing the initial concentration of naphthalene and increasing the contact time, the efficiency of the process was developed. However, an increase in the dose of nanoparticles to 0.8 g/L had enhance the efficiency of the process was enhanced, while increasing its amount to values higher than 0.8 g/L has been associated with a decrease in removal efficiency.The results of this study showed that the use of UV/ZnOphotocatalytic process can be addressed as a well-organized method to remove naphthalene from aqueous solutions.

scholarly journals A Study on the Mechanism and Kinetic of Nitrate Reduction by the nZVI-g-C3N4/TiO2  Composite Under the Simulated Sunlight

2021 ◽  
Author(s):  
Linyu Wei ◽  
Jing Tian ◽  
Qing Wang ◽  
Yuanyuan Liu ◽  
Yi Yu ◽  
...  
Keyword(s):  
Nitrate Reduction ◽  
Reduction Method ◽  
Nitrate Removal ◽  
Simulated Sunlight ◽  
Photoelectric Properties ◽  
Phase Reduction ◽  
Reduction Efficiency ◽  
Initial Ph ◽  
Lamp System

Abstract g-C3N4/TiO2 composite has excellent photoelectric properties and is considered as a good carrier of nanoparticles. A novel composite of nZVI-g-C3N4/TiO2 was successfully synthesized through in-situ growth nZVI on the surface of g-C3N4/TiO2 with liquid phase reduction method. The composite was characterized by TEM, XRD, EDS and evaluated its nitrate removal efficiency. The effects of composite dosage, solution initial pH and HCOOH concentration on nitrate reduction were investigated. The results showed that nitrate was rapidly reduced by nZVI-g-C3N4/TiO2 composite. The dosage of 4 g/L nZVI-g-C3N4/TiO2 composite and 3.0 mM of HCOOH concentration was more suitable for nitrate reduction. Solution initial pH had little impact on the nitrate reduction efficiency, but affected the proportion of the nitrate reduction products. The mechanism of nitrate reduction in the nZVI-gC3N4/TiO2/HCOOH-Xe-lamp system was proposed. The nZVI-gC3N4/TiO2 composite could be considered as a viable and promising technology for water pollution remediation.

Anaerobic Benzene Biodegradation Linked to Nitrate Reduction

1999 ◽  
Vol 65 (2) ◽  
pp. 529-533 ◽  
Author(s):  
Siobhan M. Burland ◽  
Elizabeth A. Edwards
Keyword(s):  
Carbon Dioxide ◽  
Cell Growth ◽  
Nitrate Reduction ◽  
Dry Weight ◽  
Benzene Oxidation ◽  
Constant Ratio ◽  
Nitrogen Gas ◽  
Benzene Degradation ◽  
Enrichment Cultures

ABSTRACT Benzene oxidation to carbon dioxide linked to nitrate reduction was observed in enrichment cultures developed from soil and groundwater microcosms. Benzene biodegradation occurred concurrently with nitrate reduction at a constant ratio of 10 mol of nitrate consumed per mol of benzene degraded. Benzene biodegradation linked to nitrate reduction was associated with cell growth; however, the yield, 8.8 g (dry weight) of cells per mol of benzene, was less than 15% of the predicted yield for benzene biodegradation linked to nitrate reduction. In experiments performed with [14C]benzene, approximately 92 to 95% of the label was recovered in 14CO2, while the remaining 5 to 8% was incorporated into the nonvolatile fraction (presumably biomass), which is consistent with the low measured yield. In benzene-degrading cultures, nitrite accumulated stoichiometrically as nitrate was reduced and then was slowly reduced to nitrogen gas. When nitrate was depleted and only nitrite remained, the rate of benzene degradation decreased to almost zero. Based on electron balances, benzene biodegradation appears to be coupled more tightly to nitrate reduction to nitrite than to further reduction of nitrite to nitrogen gas.

scholarly journals Production of natural aroma by yeast in wastewater of cassava starch industry

2015 ◽  
Vol 35 (4) ◽  
pp. 721-732 ◽  
Author(s):  
Simone M. M. Oliveira ◽  
Simone D. Gomes ◽  
Luciane Sene ◽  
Divair Christ ◽  
Julia Piechontcoski
Keyword(s):  
Food Industry ◽  
Cassava Starch ◽  
Glucose Yield ◽  
Batch System ◽  
Low Concentrations ◽  
Chewing Gums ◽  
Biotechnological Processes ◽  
Cassava Wastewater ◽  
Yield Factor ◽  
Starch Industry

ABSTRACT 2-Phenylethanol (PE) is an aromatic alcohol with a characteristic odor of roses, widely used in food industry to modify certain aroma compositions in formulations with fruit, jam, pudding, and chewing gums, and also in cosmetic and fragrance industry. This compound occurs naturally in low concentrations in some essential oils from flowers and plants. An alternative to plants extraction are biotechnological processes. This study evaluated 2-phenylethanol’s production in cultivation of Saccharomyces cerevisiae in cassava wastewater originated from starch industry. The substrate was supplemented with glucose and L-phenylalanine in order to obtain higher 2-phenylethanol concentrations and better efficiency in glucose/2-phenylethanol conversion. It was performed using Rotatable Center Composite Design and response surface analysis. Cultures were performed under aerobic conditions in a batch system in Erlenmeyer flasks containing 50 mL of medium in shaker at 150 rpm and 24 ± 1 ºC. The highest PE values were obtained with supplementation of 20.0 g.L-1 of glucose and 5.5 g.L-1 of L-phenylalanine, which has been experimentally validated, obtaining a PE production of 1.33 g.L-1 and PE/glucose yield factor of 0.070 g.g-1, equivalent to 74.3 and 89.7% of desirability values according to the validated model.

scholarly journals Biogenic Fe(II-III) Hydroxycarbonate Green Rust Enhances Nitrate Removal and Decreases Ammonium Selectivity during Heterotrophic Denitrification

Minerals ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 818
Author(s):  
Georges Ona-Nguema ◽  
Delphine Guerbois ◽  
Céline Pallud ◽  
Jessica Brest ◽  
Mustapha Abdelmoula ◽  
...  
Keyword(s):  
Nitrate Reduction ◽  
Nitrate Removal ◽  
Green Rust ◽  
Nitrite Reduction ◽  
Nitrite Accumulation ◽  
Bacterial Reduction ◽  
Water Treatment Process ◽  
Nitrite Production ◽  
Ammonium Production ◽  
Biogenic Iron

Nitrification-denitrification is the most widely used nitrogen removal process in wastewater treatment. However, this process can lead to undesirable nitrite accumulation and subsequent ammonium production. Biogenic Fe(II-III) hydroxycarbonate green rust has recently emerged as a candidate to reduce nitrite without ammonium production under abiotic conditions. The present study investigated whether biogenic iron(II-III) hydroxycarbonate green rust could also reduce nitrite to gaseous nitrogen during bacterial nitrate reduction. Our results showed that biogenic iron(II-III) hydroxycarbonate green rust could efficiently decrease the selectivity of the reaction towards ammonium during heterotrophic nitrate reduction by native wastewater-denitrifying bacteria and by three different species of Shewanella: S. putrefaciens ATCC 12099, S. putrefaciens ATCC 8071 and S. oneidensis MR-1. Indeed, in the absence of biogenic hydroxycarbonate green rust, bacterial reduction of nitrate converted 11–42% of the initial nitrate into ammonium, but this value dropped to 1–28% in the presence of biogenic hydroxycarbonate green rust. Additionally, nitrite accumulation did not exceed the 2–13% in the presence of biogenic hydroxycarbonate green rust, versus 0–28% in its absence. Based on those results that enhance the extent of denitrification of about 60%, the study proposes a water treatment process that couples the bacterial nitrite production with the abiotic nitrite reduction by biogenic green rust.

scholarly journals Electrochemical removal of nitrate from a Donnan dialysis waste stream

2019 ◽  
Vol 80 (4) ◽  
pp. 727-736 ◽  
Author(s):  
Judah Makover ◽  
David Hasson ◽  
Yunyan Huang ◽  
Raphael Semiat ◽  
Hilla Shemer
Keyword(s):  
High Salinity ◽  
Nitrate Removal ◽  
Waste Stream ◽  
Contaminated Groundwater ◽  
Nacl Solution ◽  
Promising Technique ◽  
Donnan Dialysis ◽  
Batch System ◽  
Anionic Composition ◽  
Electrochemical Removal

Abstract The objective of this work was to investigate electrochemical removal of nitrate from a high salinity waste stream generated by Donnan dialysis. Donnan dialysis for nitrate removal is a promising technique. It produces a distinctive composition of a high salinity waste stream of NaCl or Na2SO4 that requires a viable disposal method. The waste stream has the full anionic composition of contaminated groundwater, but the only cation is sodium. Experiments were conducted in a batch system setup. A copper cathode was chosen over brass, aluminum and graphite cathodes. A dimensionally stable anode (DSA), Ti/PbO2, was selected over a Ti/Pt anode. Electrochemical denitrification of high salinity Donnan dialysis nitrate wastes was successfully achieved, with different behavior exhibited in high salinity NaCl solution than in high salinity Na2SO4 solution. NaCl inhibited nitrate removal at high salinities while Na2SO4 did not. The maximum removals after 4 h operation in the high salinity wastes were 69 and 87% for the NaCl and Na2SO4 solutions respectively.

Purification of Contaminated Water with Chromium (VI) Using Pseudomonas aeruginosa

2016 ◽  
Vol 721 ◽  
pp. 143-148 ◽  
Author(s):  
Nora Noureddine ◽  
Samia Benhammadi ◽  
Fouad Kara ◽  
Hakim Aguedal ◽  
Abdelkader Iddou ◽  
...  
Keyword(s):  
Pseudomonas Aeruginosa ◽  
Hexavalent Chromium ◽  
Contact Time ◽  
Culture Broth ◽  
Contaminated Water ◽  
Toxic Heavy Metals ◽  
Initial Concentration ◽  
Chromium Vi ◽  
Batch System ◽  
Uncontaminated Soil

A bacterial strain Pseudomonas aeruginosa isolated from an uncontaminated soil has been used for the removal of hexavalent chromium (Cr (VI)). The experiments were carried out in batch system in a culture broth. The results obtained have shown that 100% of Cr (VI) are removed. Contact time, initial concentration of the hexavalent chromium, temperature, as well as the nature of the culture broth have influenced this elimination. To the initial concentration of 20g/L of Cr (VI) the elimination rates are lower, while the reverse occurs for an initial concentration of 8g/L. This study allows considering the use of Pseudomonas aeruginosa in the treatment of water polluted by toxic heavy metals such as Cr (VI).

Sign in / Sign up

Export Citation Format

Share Document