Evaluation of the causes of inundation in a repeatedly flooded zone in the city of Cheongju, Korea, using a 1D/2D model

2014 ◽  
Vol 69 (11) ◽  
pp. 2175-2183 ◽  
Author(s):  
In-Hyeok Park ◽  
Jeong-Yong Lee ◽  
Ji-Heon Lee ◽  
Sung-Ryong Ha
Keyword(s):  
Type A ◽  
Storm Event ◽  
Type B ◽  
Local Flow ◽  
Sewer Systems ◽  
Type C ◽  
Sewer Overflows ◽  
The Impact ◽  
The City ◽  
2D Model

Currently, unprecedented levels of damage arising from major weather events have been experienced in a number of major cities worldwide. Furthermore, the frequency and the scale of these disasters appear to be increasing and this is viewed by some as tangible proof of climate change. In the urbanized areas sewer overflows and resulting inundation are attributed to the conversion of previous surfaces into impervious surfaces, resulting in increased volumes of runoff which exceed the capacity of sewer systems and in particular combined sewer systems. In this study, the characteristics of sewer overflows and inundation have been analyzed in a repeatedly flooded zone in the city of Cheongju in Korea. This included an assessment of inundation in a 50-year storm event with total rainfall of 165 mm. A detailed XP-SWMM 2D model was assembled and run to simulate the interaction of the sewerage system overflows and surface inundation to determine if inundation is due to hydraulic capacity limitations in the sewers or limitations in surface inlet capacities or a combination of both. Calibration was undertaken using observation at three locations (PT #1, PT #2, PT #3) within the study area. In the case of the subsurface flow calibration, R2 value of 0.91 and 0.78 respectively were achieved at PT #1 and PT #2. Extremely good agreement between observed and predicted surface flow depths was achieved also at PT #1 and PT #2. However, at PT #3 the predicted flow depth was 4 cm lower than the observed depth, which was attributed to the impact of buildings on the local flow distribution. Areas subject to flooding were classified as either Type A (due to insufficient hydraulic capacity of a sewer), Type B (which is an area without flooding notwithstanding insufficient hydraulic capacity of a sewer) or Type C (due to inlet limitations, i.e. there is hydraulic capacity in a sewer which is not utilized). In the total flooded zone, 24% was classified as Type A (10.2 ha) and 25% was classified as Type C (2.61 ha). It was concluded that greater attention should be paid to the area classified as Type B, which covers 50.5% (5.15 ha) of the total flooded zone.

scholarly journals The effectiveness of TiO2 additions to mortar to maintain initial conditions in terms of its reflectance to solar radiation

2017 ◽  
Vol 17 (3) ◽  
pp. 39-56 ◽  
Author(s):  
Sérgio Roberto Andrade Dantas ◽  
Fulvio Vittorino ◽  
Kai Loh
Keyword(s):  
Solar Radiation ◽  
Ultraviolet Radiation ◽  
Initial Conditions ◽  
Type A ◽  
Just Noticeable Difference ◽  
Type B ◽  
Climate Conditions ◽  
Type D ◽  
Type C ◽  
Over Time

Abstract Contact of facades with degradation agents and direct incidence of ultraviolet radiation on external coatings make them more opaque over time, affecting their colour and reflectance characteristics. This study evaluated the effect of adding different TiO2 contents to mortars applied in concrete substrates in order to verify the reflectance maintenance on surfaces after exposure over time. Mortar with different concentrations of TiO2 (1%, 5%, 10%) were produced in relation to the total dry premix, added as a powder and compared to unpainted mortar without TiO2 (type "A") and painted mortar without TiO2 (type "B"), both used as a reference for colour and reflectance. Exposed over 16 months to climate conditions in São Paulo, regarding the maintenance of reflectance and solar radiation, the results showed that type "B" (0%TiO2) painted mortar presented the best performance. Type "C" (1%TiO2) and type "D" (5%TiO2) unpainted mortar remained more stable. Type "A" (0%TiO2) and type "E" (10%TiO2) unpainted mortar showed greater differences according to the Just Noticeable Difference (JND) range caused by dirt pick up.

scholarly journals Diel and seasonal courses of ambient carbon dioxide concentration and their effect on productivity of the epilithic lichen Lecanora muralis in a temperate, suburban habitat

2008 ◽  
Vol 40 (05) ◽  
pp. 449-462 ◽  
Author(s):  
Otto L. LANGE ◽  
T. G. Allan GREEN
Keyword(s):  
Carbon Dioxide Concentration ◽  
Net Photosynthesis ◽  
Type A ◽  
Botanical Garden ◽  
Early Morning ◽  
Average Concentration ◽  
Global Average ◽  
Annual Carbon ◽  
Type C ◽  
The City

Abstract:Ambient CO2 concentration (together with CO2 exchange and microclimate) was recorded every 30 min for 15 months for Lecanora muralis growing in the Botanical Garden Würzburg (Germany, northern Bavaria), a habitat on the outskirts of the city. Annual mean CO2 was around 17 ppm higher than the global average reported for the time of measurement (361 ppm; 1995/96), and daily values ranged from 317 to 490 ppm. Diel courses of CO2 could be classified into three different types. Type A, when CO2 levels rose overnight and then fell strongly to below global levels during the day, which predominated in the summer (about 75 of days); Type B, irregular diel courses occurred during all seasons with often very rapid changes apparently due to advective CO2 transport; Type C, CO2 concentration was typically almost stable at generally between c. 330 and 430 ppm which predominated in the winter (63 of days).Under controlled conditions, CO2 saturation of net photosynthesis (NP) of L. muralis at optimal hydration and light occurred at around 1000 ppm. NP was also affected by low CO2 at limiting light and thallus water contents. Based upon these data, we estimated the improvement of NP of L. muralis due to transient increase of ambient CO2 (as compared with the global average) for one selected combination of environmental factors (nocturnal dew or frost). This combination is an important source of water for the lichen, resulting in 40 of its annual production and, especially in these situations, photosynthesis was increased by high ambient CO2 in the early morning under prevailing Type A conditions. After dew activation, light compensation point of NP occurred at an average concentration of 413 ppm and diel maxima of NP at 402 ppm. This allows a rough estimate that the transiently elevated CO2 increased the photosynthetic gain of the lichen after dew of 7, or an improvement to its annual carbon balance of about 3. Conditions, especially interrelationships between lichen hydration, light and CO2 are so complex that we are not yet able to extend our estimates to other environmental situations of photosynthetic activity of L. muralis.

Judgments of Grammatically by Normal and Language-Disordered Children

1977 ◽  
Vol 42 (2) ◽  
pp. 199-209 ◽  
Author(s):  
Betty Z. Liles ◽  
Martin D. Shulman ◽  
Susan Bartlett
Keyword(s):  
Word Order ◽  
Sentence Type ◽  
Type A ◽  
Order Type ◽  
Specific Reference ◽  
Type B ◽  
Normal Children ◽  
Grammatical Errors ◽  
Type C

Fifteen linguistically normal children and 15 linguistically deviant children were presented with three types of agrammatical sentences. The subjects were asked to judge the sentences as right or wrong and to change the sentences judged as wrong, rendering them correct. The three types of agrammatical sentences represented rule violations of syntactic agreement (Type A), lexical restrictions (Type B), and word order (Type C). The two groups of children were compared in terms of the number of sentences of each type that were recognized as agrammatical. Those productions which represented the child’s correction of agrammatical sentences were subjected to descriptive analyses (percentages) with specific reference to the number of attempted changes and the number of those changes which demonstrated corrections of the specific deviation from well formedness. Results indicated that the two groups of subjects were significantly different in their ability to recognize grammatical errors in sentence Types A and C, but did not differ in their ability to recognize errors in sentence Type B. The descriptive comparison of the groups' verbal corrections reflected this trend, in that the language-disordered subjects made corrections specific to the error on more of the Type B sentences (for example, “The dog writes the food.”) than on Types A (for example, “'She will pick some flowers last week.”) or C (for example, “Get and come your dinner.”). Linguistically normal children accurately corrected 90.7% of the sentences judged as agrammatical; this percentage did not vary more than 1% across sentence types.

scholarly journals Structural and fractal characterization of adsorption pores of middle–high rank coal reservoirs in western Yunnan and eastern Guizhou: An experimental study of coals from the Panguan syncline and Laochang anticline

2018 ◽  
Vol 37 (1) ◽  
pp. 251-272 ◽  
Author(s):  
Junjian Zhang ◽  
Chongtao Wei ◽  
Gaoyuan Yan ◽  
Guanwen Lu
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Pore Diameter ◽  
Structural Parameters ◽  
Total Pore Volume ◽  
Type A ◽  
Type B ◽  
Type C

To better understand the structural characteristic of adsorption pores (pore diameter < 100 nm) of coal reservoirs around the coalbed methane production areas of western Yunnan and eastern Guizhou, we analyzed the structural and fractal characteristics of pore size range of 0.40–2.0 nm and 2–100 nm in middle–high rank coals ( Ro,max = 0.93–3.20%) by combining low-temperature N2/CO2 adsorption tests and surface/volume fractal theory. The results show that the coal reservoirs can be divided into three categories: type A ( Ro,max < 2.15%), type B (2.15% <  Ro,max <2.50%), and type C ( Ro,max > 2.15%). The structural parameters of pores in the range from 2 to 100 nm are influenced by the degree of coal metamorphism and the compositional parameters (e.g., ash and volatile matter). The dominant diameters of the specific surface areas are 10–50 nm, 2–50 nm, and 2–10 nm, respectively. The pores in the range from <2 nm provide the largest proportion of total specific surface area (97.22%–99.96%) of the coal reservoir, and the CO2-specific surface area and CO2-total pore volume relationships show a positive linear correlation. The metamorphic degree has a much greater control on the pores (pore diameter less than 2 nm) structural parameters than those of the pore diameter ranges from 2 to 100 nm. Dv1 and Dv2 can characterize the structure of 2–100 nm adsorption pores, and Dv1 (volume heterogeneity) has a positive correlation with the pore structural parameters such as N2-specific surface area and N2-total pore volume. This parameter can be used to characterize volume heterogeneity of 2–10 nm pores. Dv2 (surface heterogeneity) showed type A > type B > type C and was mainly affected by the metamorphism degree. Ds2 can be used to characterize the pore surface heterogeneity of micropores in the range of 0.62–1.50 nm. This parameter has a good correlation with the pore parameters (CO2-total pore volume, CO2-specific surface area, and average pore size) and is expressed as type C < type B < type A. In conclusion, the heterogeneity of the micropores is less than that of the meso- and macropores (2–100 nm). Dv1, Dv2, and Ds2 can be used as effective parameters to characterize the pore structure of adsorption pores. This result can provide a theoretical basis for studying the pore structure compatibility of coal reservoirs in the region.

scholarly journals Postsurgical residual lung complications following left upper trisegmentectomy

2019 ◽  
Author(s):  
Yutaro Koike ◽  
Aritoshi Hattori ◽  
Takeshi Matsunaga ◽  
Kazuya Takamochi ◽  
Shiaki Oh ◽  
...  
Keyword(s):  
Surgical Intervention ◽  
Type A ◽  
X Rays ◽  
Limited Information ◽  
Type B ◽  
Type D ◽  
Thoracic Computed Tomography ◽  
Isolated Segment ◽  
Type C ◽  
Lung Torsion

AbstractOBJECTIVESSegmentectomy has become an increasingly popular surgical procedure for small-sized lung lesions. Left upper trisegmentectomy (LUTS) is one of the most common segmentectomies performed because of its relative ease and simplicity; however, limited information is currently available on the specific postoperative complications associated with this procedure.METHODSAmong 2060 surgically resected cases in our institute between 2009 and 2016, 129 (6.2%) underwent LUTS. Postoperative chest X-rays and/or thoracic computed tomography (CT) scans were retrospectively assessed for all cases to assess postsurgical residual lung complications following LUTS. We categorized cases into 4 groups: type A (atelectasis of the lingular segment), type B (lung torsion of the lingular segment), type C (necrosis of the ‘isolated segment’) and type D (haematoma along stapling lines).RESULTSPostsurgical lung complications following LUTS were observed in 17 (13.1%) patients (type A: n = 7, type B: n = 1, type C: n = 4 and type D: n = 5). Three patients (2.3%) required surgical intervention because of type B (n = 1) and type C (n = 2), namely, decreased permeability and remaining ground glass opacities in the residual lung, showing an exacerbated systemic inflammatory response. In contrast, type A and D cases were successfully observed by chest CT without any surgical intervention, and patients recovered within a few months of surgery.CONCLUSIONSWe identified several postoperative residual lung complications following LUTS. Lung torsion or necrosis of the residual segment may require intensive care, including reoperation. Potentially serious complications always need to be ruled out after LUTS when radiological consolidation is detected postoperatively.

Research on Flow Units of Extra-Low Permeability Reservoirs in Fault Block Sheng554 of Shengping Oilfield

2013 ◽  
Vol 295-298 ◽  
pp. 3162-3165
Author(s):  
Lu Lu Zhou ◽  
Zi Nan Li ◽  
Jun Gang Liu ◽  
Yan Yun Zhang ◽  
Guang Qiang Shu
Keyword(s):  
Fluid Flow ◽  
Water Injection ◽  
Type A ◽  
Low Permeability ◽  
Type B ◽  
Flow Units ◽  
Fault Block ◽  
Remaining Oil ◽  
Type C ◽  
Low Permeability Reservoirs

Taking the example of the fourth member of the Lower Cretaceous Quantou formation reservoirs in fault block Sheng554 of Sanzhao sag, this article discusses the methodology of flow units in extra-low permeability reservoirs. The research on flow units in such reservoirs can be divided into two ranks, one is to determine the distribution of seepage barriers and inner connected sands， the other is to analyze the differentia of fluid flow in the inner connected sands so as to subdivide the flow units. The result shows that the pelitic barriers are rather developed in fault block Sheng554. Through the analysis of differentia of fluid flow, according to the value of flow zone index (FZI), the inner connected sands can be classified into three types of flow units, among which type A with FZI value greater than 1.0 has better permeable property and higher intensity of water injection, and the ability of permeability and water injection of type B with FZI value between 0.5 and 1.0 takes the second place, and type C is the worst flow unit with the worst permeable property and intensity of water injection with FZI value less than 0.5. Among the three types of flow units, type A poorly develops, while type B and type C develops well. The research on flow units can provide reliable geologic bases for forecasting the distribution of remaining oil in extra-low permeability reservoirs and for developing remaining oil in the study area.

A New Classification of Cochleovestibular Malformations and Implications for Predicting Speech Perception Ability after Cochlear Implantation

2015 ◽  
Vol 20 (2) ◽  
pp. 90-101 ◽  
Author(s):  
Sung-Wook Jeong ◽  
Lee-Suk Kim
Keyword(s):  
Speech Perception ◽  
Cochlear Implantation ◽  
Test Scores ◽  
Type A ◽  
Cochlear Nerve ◽  
Type B ◽  
New Classification ◽  
Type D ◽  
Type C

Objectives: The aims of this study were to introduce a new classification of cochleovestibular malformation (CVM) and to investigate how well this classification can predict speech perception ability after cochlear implantation in children with CVM. Methods: Fifty-nine children with CVM who had used a cochlear implant for more than 3 years were included. CVM was classified into 4 subtypes based on the morphology of the cochlea and the modiolus on temporal bone computed tomography (TBCT): normal cochlea and normal modiolus (type A, n = 16), malformed cochlea and partial modiolus (type B, n = 31), malformed cochlea and no modiolus (type C, n = 6), and no cochlea and no modiolus (type D, n = 6). Speech perception test scores were compared between the subtypes of CVM using analysis of covariance with post hoc Bonferroni test. Univariate and multivariate regression analyses were used to identify the significant predictors of the speech perception test scores. Results: The speech perception test scores after implantation were significantly better in children with CVM type A or type B than in children with CVM type C or type D. The test scores did not differ significantly between the implanted children with CVM type A or type B and those without CVM. In univariate regression analysis, the type of CVM was a significant predictor of the speech perception test scores in implanted children with CVM. Multivariate regression analysis revealed that the age at cochlear implantation, cochlear nerve size and preimplantation speech perception test scores were significant predictors of the postimplantation speech perception test scores. The chance of cochlear nerve deficiency increased progressively from CVM type A to type D. Conclusion: The new classification of CVM based on the morphology of the cochlea and the modiolus is simple and easy to use, and correlated well with postimplantation speech perception ability and cochlear nerve status. This simple classification of CVM using TBCT with cochlear nerve assessment by magnetic resonance imaging is helpful in the preoperative evaluation of children with CVM.

GROUPING OF ISOLATES OF A LOW-TEMPERATURE BASIDIOMYCETE ON THE BASIS OF CULTURAL BEHAVIOR AND PATHOGENICITY

1961 ◽  
Vol 39 (2) ◽  
pp. 297-306 ◽  
Author(s):  
E. W. B. Ward ◽  
J. B. Lebeau ◽  
M. W. Cormack
Keyword(s):  
Low Temperature ◽  
Host Plants ◽  
Type A ◽  
Effect Of Temperature ◽  
Western Canada ◽  
Type B ◽  
Highly Pathogenic ◽  
Cultural Behavior ◽  
Type C ◽  
Ph Range

Isolates of an unidentified low-temperature basidiomycete, associated with snow mold in Western Canada, were divided into three types, A, B, and C, on the basis of their general cultural appearance. Support for this classification was obtained when representative isolates of each type were examined to determine: the effect of temperature and pH on growth; tolerance of antibiotics and HCN; ability to liberate HCN in culture and in the host plant; pathogenicity.Type A isolates grew slowly under most conditions and were least tolerant of the extremes of temperature and pH employed, moderately inhibited by antibiotics, and strongly inhibited by HCN. They produced HCN in large quantities in host plants and none in culture. They were moderately pathogenic on grass and highly pathogenic on alfalfa. Type B isolates grew somewhat more rapidly than type A, especially at the upper and lower temperatures, and grew over a wider pH range. These isolates were more tolerant of antibiotics and HCN. They produced smaller quantities of HCN than type A in infected alfalfa plants but released large amounts in culture. They were less pathogenic than type A on alfalfa but similarly pathogenic on grass. Type C isolates were fast-growing forms which were strongly inhibited by antibiotics and HCN. They did not liberate HCN under any conditions and were not pathogenic.

A Molecular Dynamics Simulation Study on the Relationship between Hydrogen Bond and Damping Properties of AO-70/NBR Composites

2017 ◽  
Vol 748 ◽  
pp. 29-34 ◽  
Author(s):  
Jing Zhu ◽  
Xiu Ying Zhao ◽  
Meng Song ◽  
Yue Han ◽  
Li Liu ◽  
...  
Keyword(s):  
Md Simulation ◽  
Type A ◽  
Dynamics Simulation ◽  
Butadiene Rubber ◽  
Damping Properties ◽  
Type B ◽  
Fractional Free Volume ◽  
Type C ◽  
Hindered Phenol ◽  
The Relationship

This work was try to study the number and types of hydrogen bonds (H-bonds) formed in hindered phenol AO-70/nitrile butadiene rubber (NBR) composites and their contributions to the damping properties by molecular dynamic (MD) simulation and experimental methods. MD simulation results showed that there were four types of H-bonds, namely, type A (AO-70) –OH...NC– (NBR) H-bonds in AO-70/NBR composites, type B (AO-70) –OH...O=C– (AO-70) H-bonds, type C (AO-70) –OH...OH–(AO-70) and D (AO-70) –OH...O–C– (AO-70) H-bonds, what's more, type A and type B H-Bonds formed more easily than others. Fourier transform infrared spectroscopy (FTIR) confirmed the existence of H-bonds. Meanwhile, the AO-70/NBR composites with AO-70 content of 109 phr had the largest number of H-bonds, smallest fractional free volume (FFV) and resulting in the optimistic damping performance of the composites.

Protein Banding Patterns in the Ramalina Siliquosa Group

1986 ◽  
Vol 18 (3) ◽  
pp. 231-240 ◽  
Author(s):  
J. E. Mattsson ◽  
I. Kärnefelt
Keyword(s):  
Chemical Compounds ◽  
Type A ◽  
Type B ◽  
Secondary Chemistry ◽  
Banding Patterns ◽  
Swedish West Coast ◽  
Developmental Factors ◽  
Type C ◽  
Different Populations ◽  
Morphological Differences

AbstractThe value of primary chemical compounds correlated with known secondary chemistry and morphological variation within the Ramalina siliquosa group has been investigated. A hundred specimens were collected on two different occasions from 13 different populations on the Swedish west coast during April 1984. Protein extracts were prepared from 27 on secondary constituents identified and morphologically analysed populations. The protein bandings were performed by means of isoelectric focusing. Twenty-two different banding patterns were analysed since two were destroyed during preparation and three others yielded weak patterns. The results indicated that three different banding pattern types could be discerned: type A originated from material containing norstictic acid, stictic acid, norstictic acid in combination with stictic acid and on acid-deficient material; type B originated from material containing salazinic acid or salazinic acid in combination with protocetraric acid; and type C originated from material containing salazinic acid, protocetraric acid, salazinic acid in combination with protocetraric acid or on acid-deficient material. Material of banding type A belonged morphologically to R. cuspidata (Ach.) Nyl. and material of banding types B and C to R. siliquosa (Hudson) A. L. Smith. Seasonal and developmental factors can, however, affect the production of both primary and secondary constituents. Since there are no obvious morphological differences between the different chemical races within R. siliquosa s. str. and as material of salazinic acid in combination with protocetraric acid yielded both type B and type C banding patterns, the results do not support a taxonomy in the R. siliquosa group recognizing more than two species.

Sign in / Sign up

Export Citation Format

Share Document