scholarly journals The SHARON process in the treatment of landfill leachate

2010 ◽  
Vol 61 (1) ◽  
pp. 47-52 ◽  
Author(s):  
A. Vilar ◽  
M. Eiroa ◽  
C. Kennes ◽  
M. C. Veiga
Keyword(s):  
Organic Matter ◽  
Landfill Leachate ◽  
Previous Treatment ◽  
Cod Removal ◽  
Partial Nitrification ◽  
Ammonium Concentration ◽  
Partial Nitritation ◽  
Pre Treatment ◽  
Anammox Process ◽  
Sharon Process

The purpose of this paper was to study the partial nitrification of the nitrogen present in a landfill leachate applying the SHARON process in order to obtain a suitable effluent to the ANAMMOX process. As a first step, the SHARON reactor was fed anaerobically pre-treated leachate at an ammonium concentration of 2,000 mg N/L (1.1 kg N/m3 d). In such conditions, the average ammonium and nitrite concentrations in the effluent were 775 mg N/L and 1,225 mg N/L, respectively. During this period the COD removal was very low since most of the biodegradable organic matter was removed in the anaerobic pre-treatment. Afterwards, the SHARON reactor was fed leachate without a previous treatment and the efficiency of the partial nitritation diminished. As well, the COD removal increased, achieving a percentage around 28%.

Heterotrophic denitrification on granular anammox SBR treating urban landfill leachate

2008 ◽  
Vol 58 (9) ◽  
pp. 1749-1755 ◽  
Author(s):  
M. Ruscalleda ◽  
H. López ◽  
R. Ganigué ◽  
S. Puig ◽  
M. D. Balaguer ◽  
...  
Keyword(s):  
Organic Matter ◽  
Nitrogen Removal ◽  
Landfill Leachate ◽  
Anammox Bacteria ◽  
Partial Nitritation ◽  
Nitrogen Consumption ◽  
The Stability ◽  
Anammox Process ◽  
Heterotrophic Denitrification ◽  
Biodegradable Organic Matter

The anammox process was applied to treat urban landfill leachate coming from a previous partial nitritation process. In presence of organic matter, the anammox process could coexist with heterotrophic denitrification. The goal of this study was to asses the stability of the anammox process with simultaneous heterotrophic denitrification treating urban landfill leachate. The results achieved demonstrated that the anammox process was not inactivated by heterotrophic denitrification. Moreover, part of the nitrate produced by anammox bacteria and part of the influent nitrite were removed by heterotrophic denitrifiers with associated biodegradable organic matter consumption. In this sense, the contribution on nitrogen removal of each process was calculated using a nitrogen mass balance methodology. An 85.1±5.6% of the nitrogen consumption was achieved via anammox process while the average heterotrophic denitrifiers contribution was 14.9±5.6%. Heterotrophic denitrification was limited by the available easily biodegradable organic matter.

scholarly journals UVA-LED Technology’s Treatment Efficiency and Cost in a Competitive Trial Applied to the Photo-Fenton Treatment of Landfill Leachate

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1026
Author(s):  
Javier Tejera ◽  
Antonio Gascó ◽  
Daphne Hermosilla ◽  
Víctor Alonso-Gomez ◽  
Carlos Negro ◽  
...  
Keyword(s):  
Landfill Leachate ◽  
Mercury Vapor ◽  
Cod Removal ◽  
Treatment Efficiency ◽  
Alternative Source ◽  
Effluent Quality ◽  
Radiation Sources ◽  
Initial Ph ◽  
Pre Treatment ◽  
Set Up

The objective of this trial was to assess the application of UVA-LED technology as an alternative source of irradiation for photo-Fenton processes, aiming to reduce treatment costs and provide a feasible treatment for landfill leachate. An optimized combination of coagulation with ferric chloride followed by photo-Fenton treatment of landfill leachate was optimized. Three different radiation sources were tested, namely, two conventional high-pressure mercury-vapor immersion lamps (100 W and 450 W) and a custom-designed 8 W 365 nm UVA-LED lamp. The proposed treatment combination resulted in very efficient degradation of landfill leachate (COD removal = 90%). The coagulation pre-treatment removed about 70% of the COD and provided the necessary amount of iron for the subsequent photo-Fenton treatment, and it further favored this process by acidifying the solution to an optimum initial pH of 2.8. The 90% removal of color improved the penetration of radiation into the medium and by extension improved treatment efficiency. The faster the Fenton reactions were, as determined by the stoichiometric optimum set-up reaction condition of [H2O2]0/COD0 = 2.125, the better were the treatment results in terms of COD removal and biodegradability enhancement because the chances to scavenge oxidant agents were limited. The 100 W lamp was the least efficient one in terms of final effluent quality and operational cost figures. UVA-LED technology, assessed as the application of an 8 W 365 nm lamp, provided competitive results in terms of COD removal, biodegradability enhancement, and operational costs (35–55%) when compared to the performance of the 450 W conventional lamp.

scholarly journals Optimization and Modelling of Chemical Oxygen Demand Removal by ANAMMOX Process Using Response Surface Methodology

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Ali Jalilzadeh ◽  
Ramin Nabizadeh ◽  
Alireza Mesdaghinia ◽  
Aliakbar Azimi ◽  
Simin Nasseri ◽  
...  
Keyword(s):  
Chemical Oxygen Demand ◽  
Response Surface ◽  
Oxygen Demand ◽  
Cod Removal ◽  
Ammonium Concentration ◽  
Ammonium Oxidation ◽  
Optimum Conditions ◽  
Surface Method ◽  
Anammox Process ◽  
Modelling And Optimization

A systematic model for chemical oxygen demand (COD) removal using the ANAMMOX (Anaerobic AMMonium OXidation) process was provided based on an experimental design. At first, the experimental data was collected from a combined biological aerobic/anaerobic reactor. For modelling and optimization of COD removal, the main parameters were considered, such as COD loading, ammonium, pH, and temperature. From the models, the optimum conditions were determined as COD 97.5 mg/L, ammonium concentration equal to 28.75 mg-N/L, pH 7.72, and temperature 31.3°C. Finally, the analysis of the optimum conditions, performed by the response surface method, predicted COD removal efficiency of 81.07% at the optimum condition.

Use of dairy reject and fermented Aleo sp. Leaf Gel mixture in the biological Pre-treatment of landfill leachate

2018 ◽  
Vol 13 (1) ◽  
pp. 219-228 ◽  
Author(s):  
Kasmi Mariam ◽  
Elleuch Lobna ◽  
Abidi Haifa ◽  
Cherni Yassmine ◽  
Hosni Cyrine ◽  
...  
Keyword(s):  
Saccharomyces Cerevisiae ◽  
Organic Matter ◽  
Size Effect ◽  
Landfill Leachate ◽  
Yeast Strain ◽  
Oxygen Demand ◽  
Treatment Efficiency ◽  
Chemical Oxygen Demand Removal ◽  
Pre Treatment ◽  
Aloe Gel

Abstract In this study the biotreatability of Jebel Chakir landfill leachate (Tunisia) using a mixture of dairy industry reject (bactofugate) and Aloe sp. leaf gel was evaluated. The effect of Aloe gel fermentation using Saccharomyces cerevisiae yeast strain was investigated against some selected bacterial and fungal strains. The inoculation size effect of the treatment mixtures (2, 6, 10 and 12%) in the treatment efficiency was also studied. The obtained results showed that when natural Aloe gel and bactofugate mixtures were used the recorded chemical oxygen demand removal rates exceeded 56% within 48 h of treatment. Whereas, the use of the fermented Aloe gel in the treatment mixtures has promoted the organic matter removal to reach 72%.

Treatment of Landfill Leachate by Anammox Process

2020 ◽  
pp. 1169-1191
Author(s):  
Grzegorz Cema ◽  
Adam Sochacki
Keyword(s):  
Nitrogen Removal ◽  
Landfill Leachate ◽  
Inorganic Compounds ◽  
Complex Mixture ◽  
Short Review ◽  
Special Focus ◽  
Ammonia Content ◽  
Partial Nitritation ◽  
Reject Water ◽  
Anammox Process

In most cases, the anammox process is used for nitrogen removal from reject water coming from dewatering of digested sludge. However, there are more industrial streams suitable for treatment by partial nitritation/anammox process. The landfill leachate may be a good example of such wastewater. Generally, landfilling is the most used solution for treatment of urban solid wastes. The problem with landfill leachate production and management is one of the most important issues associated with the sanitary landfills. These streams are highly contaminated wastewater with a complex mixture of organic and inorganic compounds and characterized by a high ammonia content and low biodegradable organic fraction matter. The objective of this chapter is the short characteristic of landfill leachate and a short review of its treatment methods with special focus on nitrogen removal by partial nitritation/anammox process.

scholarly journals Application of Anaerobic and Ozonation Processes in the Landfill Leachate Treatment

2006 ◽  
Vol 1 (3) ◽  
Author(s):  
A. Vilar ◽  
S. Gil ◽  
M. A. Aparicio ◽  
C. Kennes ◽  
M. C. Veiga
Keyword(s):  
Organic Matter ◽  
Landfill Leachate ◽  
Biological System ◽  
Contact Time ◽  
Treatment Process ◽  
Tap Water ◽  
Leachate Treatment ◽  
Ozone Dose ◽  
Pre Treatment ◽  
Ozonation Process

The optimization of leachate treatment was investigated as well as the configuration of a biological-ozonation process. The leachate used for the experiments was diluted to 1/5 with tap water and treated anaerobically. The anaerobic effluent and the raw leachate were treated with ozone in order to increase their biodegradability getting the minimum organic matter removal. Both were submitted to the ozonation process, applying a constant ozone dose and varying the contact time. The ozonation of raw leachate produced a decrease of COD and BOD5 concentrations as well as BOD5/COD ratios, applying an ozone dose of 38.72 mg/L·min and contact times between 15 and 60 minutes. Ozonation as a pre-treatment process to the biological system did not improve the biodegradability of the raw leachate. The anaerobic effluent from the reactor fed with leachate diluted to 1/5, was subjected to an ozone dose of 34.99 mg/L·min and applying different contact times. BODf values increased from 74.75 up to 1220 mg/L and BODf/COD ratios reached values higher than 1. Then, the application of ozone to the anaerobic effluent led to the improvement of the biodegradability of the leachate as well as the BODf/COD ratio for all the contact times used.

Combining partial nitritation and heterotrophic denitritation for the treatment of landfill leachate previous to an anammox reactor

2010 ◽  
Vol 61 (8) ◽  
pp. 1949-1955 ◽  
Author(s):  
R. Ganigué ◽  
J. Gabarró ◽  
H. López ◽  
M. Ruscalleda ◽  
M. D. Balaguer ◽  
...  
Keyword(s):  
Organic Matter ◽  
Total Nitrogen ◽  
Landfill Leachate ◽  
Nitrous Acid ◽  
Process Performance ◽  
Free Nitrous Acid ◽  
Partial Nitritation ◽  
Feed Strategy ◽  
The Stability ◽  
Conventional Systems

Landfill leachate can present extremely elevated concentrations of ammonium (up to 6,000 mg N-NH4+ L−1) and a low biodegradable organic matter fraction. As an alternative to conventional systems, this wastewater can be treated on a more sustainable way by a fully autotrophic partial nitritation–anammox system. The operation of the first step of this system, the partial nitritation, is critical since the elevated concentrations of ammonium and nitrite in the reactor can severely inhibit ammonium oxidizing bacteria (AOB) activity. In this way, the inclusion of anoxic phases during the feeding events to promote the denitrification via nitrite can be a good option for upgrading the process performance and increasing the stability of the system. This paper deals with the evaluation of an anoxic–aerobic step-feed strategy for the operation of a partial nitritation SBR. Results of this study have revealed a decrease on the total nitrogen inside the reactor of more than 200 mg N L−1 without prejudice on the partial nitritation process. Furthermore, this study has also allowed detecting an AOB activity reduction at the end of aerobic phases due to bicarbonate limitation and/or free nitrous acid inhibition.

Completely Autotrophic Nitrogen-Removal for Treatment of High Ammonia Leachate

2010 ◽  
Vol 113-116 ◽  
pp. 662-665
Author(s):  
Wen De Tian ◽  
Kyoung Jin An ◽  
Zhi Wei Li
Keyword(s):  
Nitrogen Removal ◽  
Removal Rate ◽  
Optimal Operation ◽  
Ammonium Concentration ◽  
Operation Condition ◽  
Partial Nitritation ◽  
Ammonium Removal ◽  
High Ammonia ◽  
Anammox Process ◽  
Autotrophic Nitrogen Removal

This study focused on the feasibility of autotrophic nitrogen removal to treat high ammonia leachate, using combined partial Nitritation and Anammox process. In partial nitritation reactor, the optimal operation condition was found with influent ammonium concentration of 1200 mg/L, DO about 3 mg/L, HRT 3 days and temperature about 31°C at the ratio of NO2-N / NH4-N effluent kept at 1.1, which is a prerequisite for the application of Anammox. In Anammox reactor, more than 85% ammonium is removed at HRT 8 days, temperature 28±1°C, and pH 8. The removal rate of nitrogen and COD in combined partial Nitritation and Anammox process are 90% and 74%, respectively. Thus, a combined process of partial nitritation and a subsequent Anammox could be an alternative solution for ammonium removal for leachate.

Sign in / Sign up

Export Citation Format

Share Document