Optimisation of aeration for activated sludge treatment with simultaneous nitrification denitrification

2008 ◽  
Vol 58 (3) ◽  
pp. 639-645 ◽  
Author(s):  
David Thauré ◽  
Cyrille Lemoine ◽  
Olivier Daniel ◽  
Nader Moatamri ◽  
Julien Chabrol
Keyword(s):  
Activated Sludge ◽  
High Performance ◽  
Treatment Plant ◽  
Pilot Scale ◽  
Full Scale ◽  
Control Law ◽  
Plant Operator ◽  
Conventional Activated Sludge ◽  
Direct Measurements ◽  
Fine Bubble

Following a promising study at pilot scale a new aeration control law has been implemented at a full scale wastewater treatment plant displaying a conventional activated sludge process. The new control law is based on the direct measurements of ammonium and nitrate concentration in the biological tank by ion selective electrodes. This control law features a cascade of two Predictive Function Controls and calculates an optimal air flow rate to be provided to the biomass through fine bubble diffusers. The results obtained at the full scale plant confirmed the high performance of this control strategy allowing to substantially reduce the amount of diffused air while providing an easy means to manage the effluent quality to the plant operator.

Enhancing nitrogen removal efficiency in a dyestuff wastewater treatment plant with the IFFAS process: the pilot-scale and full-scale studies

2017 ◽  
Vol 77 (1) ◽  
pp. 70-78 ◽  
Author(s):  
Yanjun Mao ◽  
Xie Quan ◽  
Huimin Zhao ◽  
Yaobin Zhang ◽  
Shuo Chen ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Pilot Scale ◽  
Full Scale ◽  
Nitrification And Denitrification ◽  
Dyestuff Wastewater

Abstract The activated sludge (AS) process is widely applied in dyestuff wastewater treatment plants (WWTPs); however, the nitrogen removal efficiency is relatively low and the effluent does not meet the indirect discharge standards before being discharged into the industrial park's WWTP. Hence it is necessary to upgrade the WWTP with more advanced technologies. Moving bed biofilm processes with suspended carriers in an aerobic tank are promising methods due to enhanced nitrification and denitrification. Herein, a pilot-scale integrated free-floating biofilm and activated sludge (IFFAS) process was employed to investigate the feasibility of enhancing nitrogen removal efficiency at different hydraulic retention times (HRTs). The results showed that the effluent chemical oxygen demand (COD), ammonium nitrate (NH4+-N) and total nitrogen (TN) concentrations of the IFFAS process were significantly lower than those of the AS process, and could meet the indirect discharge standards. PCR-DGGE and FISH results indicated that more nitrifiers and denitrifiers co-existed in the IFFAS system, promoting simultaneous nitrification and denitrification. Based on the pilot results, the IFFAS process was used to upgrade the full-scale AS process, and the effluent COD, NH4+-N and TN of the IFFAS process were 91–291 mg/L, 10.6–28.7 mg/L and 18.9–48.6 mg/L, stably meeting the indirect discharge standards and demonstrating the advantages of IFFAS in dyestuff wastewater treatment.

Energy savings potential of new aeration system: Full scale trials

2012 ◽  
Vol 7 (4) ◽  
Author(s):  
A. Lazić ◽  
V. Larsson ◽  
Å. Nordenborg
Keyword(s):  
Control System ◽  
Energy Consumption ◽  
Total Energy ◽  
Energy Savings ◽  
Treatment Plant ◽  
Full Scale ◽  
Total Energy Consumption ◽  
Aeration System ◽  
Fine Bubble ◽  
Aeration Control

The objective of this work is to decrease energy consumption of the aeration system at a mid-size conventional wastewater treatment plant in the south of Sweden where aeration consumes 44% of the total energy consumption of the plant. By designing an energy optimised aeration system (with aeration grids, blowers, controlling valves) and then operating it with a new aeration control system (dissolved oxygen cascade control and most open valve logic) one can save energy. The concept has been tested in full scale by comparing two treatment lines: a reference line (consisting of old fine bubble tube diffusers, old lobe blowers, simple DO control) with a test line (consisting of new Sanitaire Silver Series Low Pressure fine bubble diffusers, a new screw blower and the Flygt aeration control system). Energy savings with the new aeration system measured as Aeration Efficiency was 65%. Furthermore, 13% of the total energy consumption of the whole plant, or 21 000 €/year, could be saved when the tested line was operated with the new aeration system.

High rate and compact single sludge pre-denitrification process for retrofit

1994 ◽  
Vol 30 (6) ◽  
pp. 31-40 ◽  
Author(s):  
Hiroyshi Emori ◽  
Hiroki Nakamura ◽  
Tatsuo Sumino ◽  
Tadashi Takeshima ◽  
Katsuzo Motegi ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Sewage Treatment ◽  
Treatment Plant ◽  
High Rate ◽  
Activated Sludge Process ◽  
Nitrogen And Phosphorus ◽  
Conventional Activated Sludge ◽  
Treatment Techniques ◽  
Conventional Activated Sludge Process ◽  
Denitrification Process

For the sewage treatment plants near rivers and closed water bodies in urbanized areas in Japan and European countries, there is a growing demand for introduction of advanced treatment processes for nitrogen and phosphorus from the viewpoints of water quality conservation and environmental protection. In order to remove nitrogen by the conventional biological treatment techniques, it is necessary to make a substantial expansion of the facility as compared with the conventional activated sludge process. In such urbanized districts, it is difficult to secure a site and much capital is required to expand the existing treatment plant. To solve these problems, a compact single sludge pre-denitrification process using immobilized nitrifiers was developed. Dosing the pellets, which are suitable for nitrifiers growth and physically durable, into the nitrification tank of single sludge pre-denitrification process made it possible to perform simultaneous removal of BOD and nitrogen in a retention time equal to that in the conventional activated sludge process even at the low water temperature of about 10 °C. The 3,000 m3/d full-scale conventional activated sludge plant was retrofitted and has been successfully operated.

Evaluating the treatment performance of a full scale Activated Sludge Plant in Islamabad, Pakistan

2012 ◽  
Vol 7 (1) ◽  
Author(s):  
S. S. Fatima ◽  
S. Jamal Khan
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Suspended Solids ◽  
Treatment Plant ◽  
Oxygen Demand ◽  
Full Scale ◽  
Operational Parameter ◽  
Mixed Liquor ◽  
Treatment Performance

In this study, the performance of wastewater treatment plant located at sector I-9 Islamabad, Pakistan, was evaluated. This full scale domestic wastewater treatment plant is based on conventional activated sludge process. The parameters which were monitored regularly included total suspended solids (TSS), mixed liquor suspended solids (MLSS), mixed liquor volatile suspended solids (MLVSS), biological oxygen demand (BOD), and chemical oxygen demand (COD). It was found that the biological degradation efficiency of the plant was below the desired levels in terms of COD and BOD. Also the plant operators were not maintaining consistent sludge retention time (SRT). Abrupt discharge of MLSS through the Surplus Activated sludge (SAS) pump was the main reason for the low MLSS in the aeration tank and consequently low treatment performance. In this study the SRT was optimized based on desired MLSS concentration between 3,000–3,500 mg/L and required performance in terms of BOD, COD and TSS. This study revealed that SRT is a very important operational parameter and its knowledge and correct implementation by the plant operators should be mandatory.

Comparison of two treatments for the removal of selected organic micropollutants and bulk organic matter: conventional activated sludge followed by ultrafiltration versus membrane bioreactor

2011 ◽  
Vol 63 (4) ◽  
pp. 733-740 ◽  
Author(s):  
E. Sahar ◽  
M. Ernst ◽  
M. Godehardt ◽  
A. Hein ◽  
J. Herr ◽  
...  
Keyword(s):  
Organic Matter ◽  
Activated Sludge ◽  
Membrane Fouling ◽  
Membrane Bioreactor ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Macrolide Antibiotics ◽  
Organic Micropollutants ◽  
Removal Rates ◽  
Conventional Activated Sludge

The potential of membrane bioreactor (MBR) systems to remove organic micropollutants was investigated at different scales, operational conditions, and locations. The effluent quality of the MBR system was compared with that of a plant combining conventional activated sludge (CAS) followed by ultrafiltration (UF). The MBR and CAS-UF systems were operated and tested in parallel. An MBR pilot plant in Israel was operated for over a year at a mixed liquor suspended solids (MLSS) range of 2.8–10.6 g/L. The MBR achieved removal rates comparable to those of a CAS-UF plant at the Tel-Aviv wastewater treatment plant (WWTP) for macrolide antibiotics such as roxythromycin, clarithromycin, and erythromycin and slightly higher removal rates than the CAS-UF for sulfonamides. A laboratory scale MBR unit in Berlin – at an MLSS of 6–9 g/L – showed better removal rates for macrolide antibiotics, trimethoprim, and 5-tolyltriazole compared to the CAS process of the Ruhleben sewage treatment plant (STP) in Berlin when both were fed with identical quality raw wastewater. The Berlin CAS exhibited significantly better benzotriazole removal and slightly better sulfamethoxazole and 4-tolyltriazole removal than its MBR counterpart. Pilot MBR tests (MLSS of 12 g/L) in Aachen, Germany, showed that operating flux significantly affected the resulting membrane fouling rate, but the removal rates of dissolved organic matter and of bisphenol A were not affected.

Model-based evaluation of a new upgrading concept for N-removal

2002 ◽  
Vol 45 (6) ◽  
pp. 169-176 ◽  
Author(s):  
S. Salem ◽  
D. Berends ◽  
J.J. Heijnen ◽  
M.C.M. van Loosdrecht
Keyword(s):  
Mathematical Modelling ◽  
Scale Up ◽  
Treatment Plant ◽  
Ammonia Concentration ◽  
Pilot Scale ◽  
Full Scale ◽  
Model Based ◽  
N Removal ◽  
Quantitative Basis ◽  
Treatment Concepts

Mathematical modelling is considered a time and cost-saving tool for evaluation of new wastewater treatment concepts. Modelling can help to bridge the gap between lab and full-scale application. Bio-augmentation can be used to obtain nitrification in activated sludge systems with a limited aerobic sludge retention time. In the present study the potential for augmenting the endogenous nitrifying population is evaluated. Implementing a nitrification reactor in the sludge return line fed with sludge liquor with a high ammonia concentration leads to augmentation of the native nitrifying population. Since the behaviour of nitrifiers is relatively well known, a choice was made to evaluate this new concept mainly based on mathematical modelling. As an example an existing treatment plant (wwtp Walcheren, The Netherlands) that needed to be upgraded was used. A mathematical model, based on the TUDP model and implemented in AQUASIM was developed and used to evaluate the potential of this bioaugmentation in the return sludge line. A comparison was made between bio-augmentation and extending the existing aeration basins and anoxic tanks. The results of both modified systems were compared to give a quantitative basis for evaluation of benefits gained from such a system. If the plant is upgraded by conventional extension it needs an increase in volume of about 225%; using a bioaugmentation in the return sludge line the total volume of the tanks needs to be expanded by only 75% (including the side stream tanks). Based on the modelling results a decision was made to implement the bioaugmentation concept at full scale without further pilot scale testing, thereby strongly decreasing the scale-up period for this process.

ADVANCED TREATMENT OF PAPER MILL EFFLUENTS BY A TWO-STAGE ACTIVATED SLUDGE PROCESS

1994 ◽  
Vol 30 (3) ◽  
pp. 173-181 ◽  
Author(s):  
L. Knudsen ◽  
J. A. Pedersen ◽  
J. Munck
Keyword(s):  
Activated Sludge ◽  
Treatment Plant ◽  
Paper Mill ◽  
Pilot Scale ◽  
Activated Sludge Process ◽  
Two Stage ◽  
Paper Mills ◽  
Paper Mill Effluents ◽  
Scale Test ◽  
Oxygen Requirements

The work presented in this paper concerns the application of a two-stage aerobic activated sludge process for treatment of effluents from paper mills in Denmark. The paper describes both pilot-scale test results and fullscale experience with the process. The treatment process is characterised by a bigh-load first stage (2-4 kg COD/kg MLSSxd) followed by a low-load second stage to secure full nitrification and denitrification of remaining nitrogen compounds. The results of continuous pilot-scale tests show that it is possible to obtain a reduction of more than 85% of the incoming COD,01 and a 99% reduction of the incoming BOD5, resulting in an effluent quality of 230 mg CODsol/l and less than 10 mg BOD5/l. As indicated, practically all the biodegradable organic substances are removed by the process. The remaining fraction of soluble organics measured as COD is considered to be non-biodegradable by conventional biological treatment systems. The results produced in the pilot-scale tests are confirmed by the effluent qualities obtained in a full-scale treatment plant at another paper mill, involving an identical process concept. During the pilot-scale tests, special attention bas been paid to the removal of organic compounds, organic nitrogen as well as nutrients and nitrification. In addition, the sludge characteristics and the oxygen requirements have been considered.

Membrane bio-reactor for textile wastewater treatment plant upgrading

2005 ◽  
Vol 52 (4) ◽  
pp. 91-98 ◽  
Author(s):  
C. Lubello ◽  
R. Gori
Keyword(s):  
Activated Sludge ◽  
Pilot Plant ◽  
Treatment Plant ◽  
Textile Wastewater ◽  
Experimental Period ◽  
Pilot Scale ◽  
Wastewater Reclamation ◽  
Textile Wastewater Treatment ◽  
Secondary Settling ◽  
Solid Liquid

Textile industries carry out several fiber treatments using variable quantities of water, from five to forty times the fiber weight, and consequently generate large volumes of wastewater to be disposed of. Membrane Bio-reactors (MBRs) combine membrane technology with biological reactors for the treatment of wastewater: micro or ultrafiltration membranes are used for solid-liquid separation replacing the secondary settling of the traditional activated sludge system. This paper deals with the possibility of realizing a new section of one existing WWTP (activated sludge+clariflocculation+ozonation) for the treatment of treating textile wastewater to be recycled, equipped with an MBR (76 l/s as design capacity) and running in parallel with the existing one. During a 4-month experimental period, a pilot-scale MBR proved to be very effective for wastewater reclamation. On average, removal efficiency of the pilot plant (93% for COD, and over 99% for total suspended solids) was higher than the WWTP ones. Color was removed as in the WWTP. Anionic surfactants removal of pilot plant was lower than that of the WWTP (90.5 and 93.2% respectively), while the BiAS removal was higher in the pilot plant (98.2 vs. 97.1). At the end cost analysis of the proposed upgrade is reported.

scholarly journals Niche Differentiation among Three Closely RelatedCompetibacteraceaeClades at a Full-Scale Activated Sludge Wastewater Treatment Plant and Putative Linkages to Process Performance

2018 ◽  
Vol 85 (5) ◽  
Author(s):  
Veronica R. Brand ◽  
Laurel D. Crosby ◽  
Craig S. Criddle
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plant ◽  
Treatment Plant ◽  
Niche Differentiation ◽  
Full Scale ◽  
Pure Oxygen ◽  
Operational Parameters ◽  
Metabolic Potential ◽  
Operational Conditions

ABSTRACTMultiple clades within a microbial taxon often coexist within natural and engineered environments. Because closely related clades have similar metabolic potential, it is unclear how diversity is sustained and what factors drive niche differentiation. In this study, we retrieved three near-complete Competibacter lineage genomes from activated sludge metagenomes at a full-scale pure oxygen activated sludge wastewater treatment plant. The three genomes represent unique taxa within theCompetibacteraceae. A comparison of the genomes revealed differences in capacity for exopolysaccharide (EPS) biosynthesis, glucose fermentation to lactate, and motility. Using quantitative PCR (qPCR), we monitored these clades over a 2-year period. The clade possessing genes for motility and lacking genes for EPS biosynthesis (CPB_P15) was dominant during periods of suspended solids in the effluent. Further analysis of operational parameters indicate that the dominance of the CPB_P15 clade is associated with low-return activated sludge recycle rates and low wasting rates, conditions that maintain relatively high levels of biomass within the system.IMPORTANCEMembers of the Competibacter lineage are relevant in biotechnology as glycogen-accumulating organisms (GAOs). Here, we document the presence of threeCompetibacteraceaeclades in a full-scale activated sludge wastewater treatment plant and their linkage to specific operational conditions. We find evidence for niche differentiation among the three clades with temporal variability in clade dominance that correlates with operational changes at the treatment plant. Specifically, we observe episodic dominance of a likely motile clade during periods of elevated effluent turbidity, as well as episodic dominance of closely related nonmotile clades that likely enhance floc formation during periods of low effluent turbidity.

Sign in / Sign up

Export Citation Format

Share Document