Identification of overall degradation in sewer systems from long-term measurements and consequences for WWTP simulations

2005 ◽  
Vol 52 (3) ◽  
pp. 153-161 ◽  
Author(s):  
M. Ahnert ◽  
V. Kuehn ◽  
P. Krebs
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plants ◽  
Sewer Systems ◽  
Transformation Processes

In-sewer transformation processes affect significantly design and operation of large wastewater treatment plants. Especially for long-term simulations the degradation has to be considered in order to avoid over- and underestimation. In this paper a method is presented to derive the overall degradation from available operation data. The application of the results in a long-term simulation of a WWTP shows the relevance of the degradation for design and operation of an activated sludge plant.

Model and Sensor Based Optimization of Nitrogen Removal at Klagshamn Wastewater Treatment Plant

1992 ◽  
Vol 26 (5-6) ◽  
pp. 1315-1323 ◽  
Author(s):  
H. Aspegren ◽  
B. Andersson ◽  
U. Nyberg ◽  
J. la C. Jansen
Keyword(s):  
Wastewater Treatment ◽  
Carbon Source ◽  
Activated Sludge ◽  
Nitrogen Removal ◽  
Wastewater Treatment Plant ◽  
Wastewater Treatment Plants ◽  
Treatment Plant ◽  
On Line ◽  
Ammonia Sensors

Optimization of wastewater treatment plants with extensive phosphorus and nitrogen removal is complicated. The Klagshamn wastewater treatment plant in Sweden is operated with pre-precipitation of phosphorus with ferric chloride and denitrification with methanol as carbon source. An activated sludge process, operated with pre-precipitation and denitrification with external carbon source in a compartmentalized plant, requires only small tank volumes but increases the need for proper operation and optimization. On-line nitrogen, ammonia, and TOC sensors are used for a day-to-day control and optimization while mathematical modelling is used for long term strategic planning. The on-line measurements are further used as the basis for the modelling. TOC and ammonia sensors at the influent clearly identify typical and extreme loading variations and nitrate measurements in the activated sludge tanks and the effluent shows the dynamics of the processes. These measurements provide a basis for model calibration. In combination low residuals of nitrogen, phosphorus and organic matter can be achieved.

scholarly journals The capacity of wastewater treatment plants drives bacterial community structure and its assembly

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Young Kyung Kim ◽  
Keunje Yoo ◽  
Min Sung Kim ◽  
Il Han ◽  
Minjoo Lee ◽  
...  
Keyword(s):  
Wastewater Treatment ◽  
Community Structure ◽  
Bacterial Community ◽  
Activated Sludge ◽  
Community Assembly ◽  
Bacterial Communities ◽  
Wastewater Treatment Plants ◽  
High Capacity ◽  
Operating Conditions ◽  
Rrna Gene

Abstract Bacterial communities in wastewater treatment plants (WWTPs) affect plant functionality through their role in the removal of pollutants from wastewater. Bacterial communities vary extensively based on plant operating conditions and influent characteristics. The capacity of WWTPs can also affect the bacterial community via variations in the organic or nutrient composition of the influent. Despite the importance considering capacity, the characteristics that control bacterial community assembly are largely unknown. In this study, we discovered that bacterial communities in WWTPs in Korea and Vietnam, which differ remarkably in capacity, exhibit unique structures and interactions that are governed mainly by the capacity of WWTPs. Bacterial communities were analysed using 16S rRNA gene sequencing and exhibited clear differences between the two regions, with these differences being most pronounced in activated sludge. We found that capacity contributed the most to bacterial interactions and community structure, whereas other factors had less impact. Co-occurrence network analysis showed that microorganisms from high-capacity WWTPs are more interrelated than those from low-capacity WWTPs, which corresponds to the tighter clustering of bacterial communities in Korea. These results will contribute to the understanding of bacterial community assembly in activated sludge processing.

scholarly journals Deep learning-based morphology classification of activated sludge flocs in wastewater treatment plants

2021 ◽  
Author(s):  
Hisashi Satoh ◽  
Yukari Kashimoto ◽  
Naoki Takahashi ◽  
Takashi Tsujimura
Keyword(s):  
Wastewater Treatment ◽  
Deep Learning ◽  
Activated Sludge ◽  
Morphological Change ◽  
Wastewater Treatment Plants ◽  
Filamentous Bacteria ◽  
Sludge Flocs

A deep learning-based two-label classifier 1 recognized a 20% morphological change in the activated flocs. Classifier-2 quantitatively recognized an abundance of filamentous bacteria in activated flocs.

Controlling the Settling of Activated Sludge in Pulp and Paper Wastewater Treatment Plants

1999 ◽  
Vol 40 (11-12) ◽  
pp. 223-229 ◽  
Author(s):  
Frédéric Clauss ◽  
Christel Balavoine ◽  
Delphine Hélaine ◽  
Gaëtan Martin
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Wastewater Treatment Plants ◽  
Pulp And Paper ◽  
Organic Load ◽  
Forest Industry ◽  
Filamentous Bulking ◽  
Mineral Particles ◽  
Mineral Powder

Forest industry wastewaters are difficult to clean: hydraulic and organic load variations, filamentous bulking or pin-point flocs negatively impact depollution processes. The addition of a fine, mineral, talc-based powder, Aquatal, into the aeration tanks of wastewater treatment plants connected to pulp and paper factories has been successfully tested since end of '97. The first case-study presents full results obtained over a period of 18 months in a 20,000 p.e. plant connected to a paper factory. The mineral powder was regularly added to control sludge volume index, thereby ensuring low suspended solids concentration in the outfluent. Plant operators could easily adapt biomass concentration to match organic load variation, thereby maintaining pollution micro-organisms ratio constant. In a second case study, a trouble-shooting strategy was implemented to counteract filamentous bulking. A one-off, large dosage enabled the plant operator to deal effectively with poor settleability sludge and rapidly control sludge blanket expansion. In both cases, the main common characteristics observed were an increase in floc aggregation and the production of heavier and well-structured flocs. The sludge settling velocity increased and an efficient solid/liquid separation was obtained. After a few days, the mineral particles of Aquatal were progressively integrated into the sludge floc structure. When the mineral powder was added to the activated sludge in the aeration basin, chemical interactions frequently encountered with other wastewater treatment additives did not pose a problem. Moreover, with this mineral additive, the biological excess sludge displayed good thickening properties and dewatering was improved. Despite the addition of the insoluble mineral particles, the amount of wet sludge expelled did not increase. Aquatal offers a rapid solution to floc settleability problems which so frequently arise when physical or biological disorders appear in forest industry wastewater treatment plants.

PARAMETERS FOR DYNAMIC SIMULATION OF W ASTEW ATER TREATMENT PLANTS WITH HIGH-RATE AND LOW-RATE ACTIVATED SLUDGE TANKS

1994 ◽  
Vol 30 (4) ◽  
pp. 211-214 ◽  
Author(s):  
E. Brands ◽  
M. Liebeskind ◽  
M. Dohmann
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Dynamic Simulation ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
High Rate ◽  
Yield Coefficient ◽  
Municipal Wastewater Treatment ◽  
Municipal Wastewater Treatment Plants ◽  
Low Rate

This study shows a comparison of important parameters for dynamic simulation concerning the highrate and low-rate activated sludge tanks of several municipal wastewater treatment plants. The parameters for the dynamic simulation of the single-stage process are quite well known, but parameters for the high-ratellow-rate activated sludge process are still missi ng, although a considerable number of wastewater treatment plants are designed and operated that way. At present any attempt to simulate their operation is restricted to the second stage due to missing data concerning growth rate, decay rate, yield coefficient and others.

Estimation of Kinetic Parameters of Heterotrophic Biomass under Aerobic Conditions and Characterization of Wastewater for Activated Sludge Modelling

1992 ◽  
Vol 25 (6) ◽  
pp. 125-139 ◽  
Author(s):  
J. Kappeler ◽  
W. Gujer
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Kinetic Parameters ◽  
Specific Growth ◽  
Wastewater Treatment Plants ◽  
Simple Method ◽  
Batch Tests ◽  
Different Types ◽  
Heterotrophic Biomass

To predict the behaviour of biological wastewater treatment plants, the Activated Sludge Model No. 1 is often used. For the application of this model kinetic parameters and wastewater composition must be known. A simple method to estimate kinetic parameters of heterotrophic biomass and COD wastewater fractions is presented. With three different types of batch-tests these parameters and fractions can be determined by measuring oxygen respiration. Our measurements showed that the maximum specific growth rate µmax of heterotrophic biomass depends on temperature, reactor configuration and SRT. In typical wastewater treatment plants of Switzerland the amount of readily biodegradable substrate was generally small (about 9 % of the COD in primary effluent). The same method can also be used to determine kinetic parameters of nitrifying biomass.

Characterization of wastewater and activated sludge from European municipal wastewater treatment plants using the NUR test

1998 ◽  
Vol 38 (1) ◽  
pp. 303-310 ◽  
Author(s):  
V. Naidoo ◽  
V. Urbain ◽  
C. A. Buckley
Keyword(s):  
Wastewater Treatment ◽  
Activated Sludge ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Municipal Wastewater Treatment ◽  
Batch Tests ◽  
Denitrification Kinetics ◽  
Municipal Wastewater Treatment Plants

Denitrification kinetics and wastewater characterization of eight different plants in Europe are discussed. Denitrification batch tests revealed three distinct rates except in the cases of Plaisir, Rostock and Orense where 4 rates were observed. The latter three plants revealed atypical rapid initial rates which were between 7 and 21 mgN/gVSS.h. All denitrification kinetics under non-limiting carbon conditions revealed fast first rates which ranged between 3.0 and 7.3 mgN/gVSS.h. Acetate was used to simulate denitrification kinetics with readily biodegradable COD present. Two subsequent rates were observed. Rates 2 and 3 ranged between 2 and 3 mgN/gVSS.h, and 1 and 2 mgN/gVSS.h, respectively. The RBCOD fraction varied between 10 and 19%, except for one of the plants where the value determined was 7%.

Sign in / Sign up

Export Citation Format

Share Document