Pre-selection of flocculants by the LUMiFuge separation analyser 114

2002 ◽  
Vol 46 (4-5) ◽  
pp. 441-446 ◽  
Author(s):  
T. Sobisch ◽  
D. Lerche
Keyword(s):  
Dynamic Behaviour ◽  
Test Procedure ◽  
Centrifugal Acceleration ◽  
Sludge Dewatering ◽  
Total Solids ◽  
Shear Sensitivity ◽  
Compression Behaviour ◽  
Sludge Cake ◽  
Kinetics Of ◽  
Selection Of

This paper reports on lab-scale investigations in relation to pre-selection of flocculants for sludge dewatering with decanter centrifuges. Results obtained were compared with CST-measurements and discussed in relation to findings under field conditions. Experiments were carried out with sewage sludges of different origin and characteristics and a number of commercial flocculants. Kinetics of sedimentation and clarification were measured as well as the compression behaviour and shear sensitivity of sludge sediments. To measure flocculant performance stability against intensive shearing, total solids in the sludge cake obtained and dewaterability of the sludge cake during the first 20-50 s of centrifugation were compared. A screening test procedure was developed. Efficient flocculants should produce high residual total solids and good initial compressibility. Lab-scale investigations deliver more reliable results if the dynamic behaviour of the sludge under centrifugal acceleration is also investigated. The separation analyser LUMiFuge 114 can provide results about the compression behaviour of sludges in the range between 10 and 100 s. So far no other method or device is known which can deliver such results.

Comparison of lime and alum as oily sludge conditioners

1997 ◽  
Vol 36 (12) ◽  
pp. 117-124 ◽  
Author(s):  
Tay Joo Hwa ◽  
S. Jeyaseelan
Keyword(s):  
Specific Resistance ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oily Sludge ◽  
Sludge Dewatering ◽  
Capillary Suction ◽  
Sludge Cake ◽  
Solids Content ◽  
Optimum Chemical

Chemical conditioning improves sludge dewatering. Choice of chemical conditioners is very much dependent on the characteristics of the sludges and the type of dewatering devices. Lime, alum, ferric chloride and polyelectrolytes are commonly used chemical conditioners. Anaerobic digested sludge samples collected from a sewage treatment plant with different oil contents varying from 1.8% to 8.0% by weight have been examined in the laboratory to find out their specific resistance, capillary suction time and filter yield. Lime and alum were used separately as conditioners. Different dosages of conditioner varying from 2% to 12% by weight were used to determine the optimum chemical dosage for varying oil contents. Lime dosages of about 6% were found to yield favourable characteristics. Addition of alum decreases the specific resistances and capillary suction times of oily sludges rapidly up to 4% dosages. Alum dosages beyond 4% only increase the solids content in the sludge cake and increase the sludge volume to be handled. A correlation between CST and specific resistance to filtration was established. CST can be measured easily and quickly in the laboratories. Using the CST and the correlation a quick prediction on dewaterability can be established.

Elaboration and Characterization of the Properties of Refractory Cr Base Alloys

2010 ◽  
Vol 72 ◽  
pp. 46-52 ◽  
Author(s):  
Laurent Royer ◽  
Stéphane Mathieu ◽  
Christophe Liebaut ◽  
Pierre Steinmetz
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Molten Glass ◽  
Energy Production ◽  
Creep Properties ◽  
Refractory Alloys ◽  
Industrial Use ◽  
Kinetics Of ◽  
Selection Of

For energy production and also for the glass industry, finding new refractory alloys which could permit to increase the process temperatures to 1200°C or more is a permanent challenge. Chromium base alloys can be good candidates, considering the melting point of Cr itself, and also its low corrosion rate in molten glass. Two families of alloys have been studied for this purpose, Cr-Mo-W and Cr-Ta-X alloys (X= Mo, Si..). A finer selection of compositions has been done, to optimize their chemical and mechanical properties. Kinetics of HT oxidation by air, of corrosion by molten glass and also creep properties of several alloys have been measured up to 1250°C. The results obtained with the best alloys (Cr-Ta base) give positive indications as regards the possibility of their industrial use.

scholarly journals Role of antigen, CD8, and cytotoxic T lymphocyte (CTL) avidity in high dose antigen induction of apoptosis of effector CTL.

1996 ◽  
Vol 184 (2) ◽  
pp. 485-492 ◽  
Author(s):  
M A Alexander-Miller ◽  
G R Leggatt ◽  
A Sarin ◽  
J A Berzofsky
Keyword(s):  
T Lymphocytes ◽  
Cytotoxic T Lymphocyte ◽  
Target Cells ◽  
High Dose ◽  
High Avidity ◽  
Apoptotic Pathway ◽  
Peptide Antigen ◽  
Kinetics Of ◽  
Selection Of

Experimental data suggest that negative selection of thymocytes can occur as a result of supraoptimal antigenic stimulation. It is unknown, however, whether such mechanisms are at work in mature CD8+ T lymphocytes. Here, we show that CD8+ effector cytotoxic T lymphocytes (CTL) are susceptible to proliferative inhibition by high dose peptide antigen, leading to apoptotic death mediated by TNF-alpha release. Such inhibition is not reflected in the cytolytic potential of the CTL, since concentrations of antigen that are inhibitory for proliferation promote efficient lysis of target cells. Thus, although CTL have committed to the apoptotic pathway, the kinetics of this process are such that CTL function can occur before death of the CTL. The concentration of antigen required for inhibition is a function of the CTL avidity, in that concentrations of antigen capable of completely inhibiting high avidity CTL maximally stimulate low avidity CTL. Importantly, the inhibition can be detected in both activated and resting CTL. Blocking studies demonstrate that the CD8 molecule contributes significantly to the inhibitory signal as the addition of anti-CD8 antibody restores the proliferative response. Thus, our data support the model that mature CD8+ CTL can accommodate an activation signal of restricted intensity, which, if surpassed, results in deletion of that cell.

Mechanodestruction of Isoprene Rubber. Part 1. Process Kinetics

2021 ◽  
Vol 80 (3) ◽  
pp. 118-122
Author(s):  
V.P. Dorozhkin ◽  
◽  
E.G. Mokhnatkina ◽  
D.N. Zemsky ◽  
A.D. Valiev ◽  
...  
Keyword(s):  
Experimental Data ◽  
Molecular Mass ◽  
Rate Constants ◽  
Oxidative Destruction ◽  
Process Kinetics ◽  
Mass Fractions ◽  
Rubber Part ◽  
Kinetics Of ◽  
Selection Of ◽  
Isoprene Rubber

A method is proposed that allows us to obtain the values of the rate constants (CR) of the processes of mechanodestruction (mechanical cracking) of kм, oxidative destruction of kо, and recombination of kр macromolecules, as well as the mass fractions of the corresponding fractions of φм, φо, and φр,r involved in the plasticization process (P) of SKI-3 isoprene rubber. The method is based on the selection of the values of these parameters that correspond to the previously obtained experimental data, using the previously obtained recurrent equations and a specially developed program. The dependences of the CR on the time P at 30oC are obtained, which allows us to describe the kinetics of the processes accompanying P at this temperature, and the changes in molecular mass (MM) in this process. It is shown that constant values of CR are established at large times of P. Refined explanations of the nature of the kinetics of the CR change at P are proposed. The MM value of SKI-3 macromolecules that have not undergone destruction is calculated, depending on the time of plasticization.

QualViz: a tool for visual representation of water quality models

2011 ◽  
Vol 63 (1) ◽  
pp. 171-177
Author(s):  
G. T. Parker
Keyword(s):  
Water Quality ◽  
Conceptual Models ◽  
Dynamic Behaviour ◽  
Specific Model ◽  
Model Complexity ◽  
Proof Of Concept ◽  
Quality Models ◽  
Biochemical Kinetics ◽  
Water Quality Models ◽  
Selection Of

As water quality models and their implementation have become increasingly diverse, complex and proprietary, a need for more thorough understanding of the differences between each alternative arises. The work presented here proposes a novel visualization paradigm for water quality applications which can be used to understand difference between implementations of identical and different conceptual models. A proof-of-concept visualization tool was developed and tested again three scenarios for four different conceptual models of biochemical kinetics. Results show representative figures illustrating how the approach can communicate differences in model complexity and dynamic behaviour. The proposed tool should help ensure more suitable application of water quality models in varied contexts. A discussion of quantifying model complexity in a single metric is also presented, and recommendations are made on the selection of various representational forms for communicating and exploring specific model characteristics.

Study on the effect of chitosan conditioning on sludge dewatering

2019 ◽  
Vol 79 (3) ◽  
pp. 501-509 ◽  
Author(s):  
Jin Zhang ◽  
Qing Hu ◽  
Jie Lu ◽  
Shuang Lin
Keyword(s):  
Moisture Content ◽  
Extracellular Polymeric Substances ◽  
Waste Water Treatment ◽  
Sewage Treatment ◽  
Organic Polymer ◽  
Sludge Dewatering ◽  
Sludge Treatment ◽  
Residual Sludge ◽  
Sludge Cake ◽  
Polymer Flocculant

Abstract The difficulty of residual sludge dehydration is the major problem in sewage treatment. The reduction of moisture content in sludge can reduce the sludge volume significantly and is conducive to the subsequent disposal of sludge. As an organic polymer flocculant, chitosan (CTS) is widely used in water and waste water treatment. In this study, CTS was used in sludge treatment to improve the sedimentation and dehydration properties of sludge. When treated with CTS, the moisture content of sludge cake decreased from 85.9% to 83.0%, the SV30 decreased to about 1/2, and the sludge volume reduced to 82.9%. Further analysis showed that the zeta potential (ζ-potential) of the sludge changed from negative value to positive value, and the D50 of the sludge was larger than that of the raw sludge. In addition, when the moisture content of the sludge cake was reduced to the lowest, the concentration of extracellular polymeric substances (EPS) and SCOD was the largest and the |ζ| decreased to the lowest. CTS improved the dehydration and sedimentation performance of sludge mainly by factors of electrical neutralization, adsorption bridging and dissolution of EPS.

Passage rate of solids and fluids in the digestive tract of buffaloes, cattle and sheep: selection of non-linear model

1997 ◽  
Vol 64 (1) ◽  
pp. 63-69 ◽  
Author(s):  
A. Amici ◽  
S. Bartocci ◽  
S. Terramoccia ◽  
F. Martillotti
Keyword(s):  
Linear Models ◽  
Latin Square ◽  
Sums Of Squares ◽  
Passage Rate ◽  
Significant Difference ◽  
Age Dependent ◽  
Non Linear ◽  
Best Fitting ◽  
Kinetics Of ◽  
Selection Of

AbstractFive mathematical models were compared to select the most satisfactory model to describe digesta kinetics of solids and fluids in the gastrointestinal tract of buffaloes (Mediterranean bulls), cattle (Friesian bulls) and sheep (Delle Langhe rams) given food at maintenance level, according to a Latin-square arrangement for four consecutive periods of 21 days. Chromium mordanted alfalfa hay and cobalt-ethylenediamine tetraacetic acid were used as nonabsorbable markers and were administered through the rumen cannula in a single dose. Four different isonitrogenous diets (N × 6·25 = 140 g/kg dry matter) with different concentrate:forage ratios (12·5:87·5, 25:75, 37·5:62·5, 50:50) were used.Faecal chromium and cobalt concentration curves were fitted with five non-linear models: three gamma (G2, G3, G4) age-dependent one-compartment, one gamma age-dependent/age-independent two-compartment (G2G1) and one multicompartment (MC).Wilcoxon tests on residual sums of squares of the different models for solids showed that MC and G4 gave a better fit than G2G1, G2, G3 for all the data and within the species. The comparison of MC v. G4 did not show any significant difference (P > 0·05) for all the data computed together or within each species. Nevertheless, MC had a higher number of curves with lower residual sums of squares in comparison with G4 and was also able to produce estimates of digesta kinetics in the second compartment.The cobalt excretion curves for fluids, considering all the data, and only within sheep, showed G4 as the best fitting model. When G4 was compared with other models no significant differences were recorded either for cattle: G4 v. G2 (F = 0·6645), G4 v. G2G1 (P = 0·0620) and for buffalo: G4 v. G2 (P = 0·1575), G4 v.G3(P = 0·0796) and G4 v. G2G1 (P = 0·1641).It is concluded that the multicompartment model (MC) and G4 model were the best fits for solids and for fluids respectively.

Sign in / Sign up

Export Citation Format

Share Document