Ozonation application in activated sludge systems for a textile mill effluent

2002 ◽  
Vol 45 (12) ◽  
pp. 305-313 ◽  
Author(s):  
D. Orhon ◽  
H. Dulkadiroğlu ◽  
S. Doğruel ◽  
I. Kabdaşli ◽  
S. Sozen ◽  
...  
Keyword(s):  
Textile Industry ◽  
Contact Time ◽  
Biological Treatment ◽  
Textile Wastewater ◽  
Color Removal ◽  
Flux Rate ◽  
Textile Mill ◽  
Treatment Results ◽  
Cod Reduction ◽  
Activated Sludge Systems

The study investigates the effect of partial ozonation of textile wastewater, both at the inlet (pre-ozonation) and the outlet (post-ozonation) of biological treatment, for the optimization of COD and color removals, both typical polluting parameters associated with the textile industry. Pre-ozonation provides at optimum contact time of 15 minutes 85% color removal, but only 19% COD reduction. Removal of the soluble inert COD fraction remains at 7%, indicating selective preference of ozone for simpler compounds. Post-ozonation is much more effective on the breakdown of refractory organic compounds and on color removal efficiency. Ozonation after biological treatment results in almost complete color removal and a 14% soluble inert COD reduction. The polishing effect of post-ozonation also proves quite attractive from an economical standpoint, involving approximately 50% of the ozone utilization at the same ozone flux rate and contact time, yet providing a lower soluble residual COD level.

scholarly journals Performances of Anoxic- Aerobic Membrane Bioreactors for The Treatment of Real Textile Wastewater

2019 ◽  
Keyword(s):  
Bacterial Communities ◽  
Textile Industry ◽  
Textile Wastewater ◽  
Pilot Scale ◽  
Membrane Bioreactors ◽  
Color Removal ◽  
Toc Removal ◽  
Recycle Ratio ◽  
Operation Period ◽  
The Impact

<p>Wastewater from textile industry is considered one of the major environmental challenges due to the large volume of highly colored, polluted and toxic effluent. This study investigated the treatability of real textile wastewater by pilot-scale anoxic-aerobic Membrane Bioreactor (MBR) system without sludge wasting for operation period of 100 days. The proposed system was investigated under different Internal Recycle (IR) ratios and the impact of IR ratio on Total Organic Carbon (TOC), Total Nitrogen (TN) and Color removals were examined. Under IR ratios between anoxic and aerobic tanks of 0.0, 0.5 and 2.0, the respective average removal efficiency of TN was 20.9%,53.4% and 71.7%, whereas average color removal of 81%, 85% and 88%, respectively was noted. The results indicated that increase of recycle ratio from 0.5 to 2.0 enhanced TN removal to about 71% and color removal to above 85%. The IR between anoxic and aerobic tanks has a significant role in TN and color removal due its effect on the development of bacterial communities. On the other hand, the results indicate over 93% TOC removal, which was independent of IR ratio.</p>

scholarly journals Treatment of Pretreated Textile Wastewater Using Modified Mbbr

2018 ◽  
Vol 7 (3.8) ◽  
pp. 106
Author(s):  
K J.Sosamony ◽  
P A.Soloman
Keyword(s):  
Magnetic Field ◽  
Textile Industry ◽  
Contact Time ◽  
Textile Wastewater ◽  
Filling Ratio ◽  
Textile Effluent ◽  
Fundamental Parameters ◽  
Film Reactor ◽  
Textile Sludge ◽  
Chemical Strategies

Currently, water pollution control is one of the major logical zones. The textile industry is a major pollution causing industry among the industrial pollutions. Treatment of textile effluent utilizing customary physical as well as chemical strategies is costly, produces enormous amounts of sludge and needs the expansion of lethal chemicals. BOD to COD proportion of textile effluent is low. Thus it is not appropriate to treat textile effluent by a solitary physicochemical or biological process. In this investigation, the textile effluent is dealt with utilizing Moving Bed Bio-film Reactor (MBBR) with the magnetic field after improving the biodegradability by the solar photo-Fenton process. The carriers in MBBR is inoculated with azoarcus bacteria isolated from textile sludge. The fundamental  parameters as pH, carrier filling ratio and contact time were optimized utilizing Box Behnken factual design. The MBBR process has most extreme efficiency at pH 7, filling ratio of 62% and a contact time 2.4 days. In this optimum condition 68.9% BOD and 80% COD  are expelled. At the point when the pretreated wastewater was dealt with MBBR reactor under the influence of magnetic field, the efficiency of the treatment is additionally expanded, so 87.4% COD expulsion and 87% BOD evacuation were accomplished at 12 mT attractive field power when exposure time was at 12 hrs.  

scholarly journals A green approach for the treatment of dye and surfactant contaminated industrial wastewater

2020 ◽  
Vol 80 (3) ◽  
pp. 615-620
Author(s):  
Ü. D. Gül
Keyword(s):  
Textile Industry ◽  
Industrial Wastewater ◽  
Biological Treatment ◽  
Textile Wastewater ◽  
Textile Dye ◽  
Synthetic Dyes ◽  
Dye Molecules ◽  
Acid Dyes ◽  
Green Approach ◽  
Excellent Color

Abstract Synthetic dyes, particularly reactive and acid dyes, are commonly used in the textile industry because of their advantages as excellent color fastness and brightness. Also, surfactants are used for an increment of coloring success in the textile industry. One of the major problems concerning textile wastewater is the treatment of the effluents containing both dyes and surfactants. Biological treatment systems are recommended as useful, economic and eco-friendly methods for treatment of industrial wastewater. The purpose of this study was to investigate the binary removal of a textile dye and a surfactant by growing Aspergillus versicolor culture in molasses medium. The effect of dye and surfactant concentration on the removal of dye and surfactant was determined. This study resulted that 100% of the surfactant and dye molecules removed together with the formation of a dye-surfactant complex by fungus. It is concluded that binary removal systems are very efficient for industrial wastewater treatment.

scholarly journals CuO Coated Electrochemically Generated Textile Wastewater Sludge and CuO Coated GAC as Potential Nano-adsorbents for Color Removal from Real Textile Wastewater

2018 ◽  
Vol 34 (4) ◽  
pp. 2144-2151
Author(s):  
Srikantha H, S. Mahesh ◽  
Sahana M
Keyword(s):  
Contact Time ◽  
Cell Voltage ◽  
Textile Wastewater ◽  
Xrd Analysis ◽  
Operating Conditions ◽  
Wastewater Sludge ◽  
Color Removal ◽  
Batch Adsorption ◽  
Batch Mode ◽  
Nano Adsorbent

A laboratory scale setup was used to remove color from real textile wastewater (TWW) using nano CuO coated electrochemically generated sludge and nano CuO coated GAC. ECC studies were conducted in batch-mode to generate sludge treating real TWW using pre-optimized 4SS electrodes using a 1.5L reactor operated at cell voltage of 18V and current density 180A/m2 at an agitation speed of 500rpm for 60min electrolysis time. SEM, FTIR and XRD analysis confirmed CuO material successfully coated/decorated on electrochemically generated sludge of size ~0.3-0.5mm and GAC of size ~0.5mm. To check the color removal efficiencies from TWW the batch adsorption studies were conducted for adsorbent dose, stirring time and pH. The optimal operating conditions achieved at pH-4, dose of 0.6g/L and 30min contact time for CuO-sludge nano-adsorbent achieving 50-55% color removal. Similarly, for CuO-GAC nano-adsorbent the optimal conditions obtained at pH-4, 0.5 g/L dose and 20min contact time achieving ~100% removal.

scholarly journals Biosorption Processof Synthetic Textile Waste-water using Bjerkandera Agustavia Response Surface Methodology (RSM)

2018 ◽  
Vol 68 ◽  
pp. 04020
Author(s):  
Ariani Dwi Astuti ◽  
Khalida Muda
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Textile Industry ◽  
Contact Time ◽  
Textile Wastewater ◽  
Quadratic Model ◽  
Biosorption Process ◽  
Physico Chemical ◽  
Inorganic Species ◽  
Effects Of Ph

Textile industry generates large quantities of wastewater. Discharging effluent of textile industry without treatment is led to the degradation of the quality of receiving water bodies.A high color, high BOD/COD and salt (Total Dissolved Solids, TDS) load are founded in the textile wastewater. Several alternative of methods,including physico-chemical methods such as filtration, carbon activated, coagulation and chemical flocculation have been used to treat textile industry wastewater. Although these methods are effective, but they are expensive and result concentrated sludge that creates a secondary disposal problem. The passive uptake of organic and inorganic species including metals and dyes from aqueous solutions by the use of non-growing/living microbial mass or their derivatives is namely biosorption.The effects of pH, weight of biosorbent, contact time and size of biosorbent in biosorption process using Bjerkandera adusta in synthetic textile wastewater were investigated and optimized using response surface methodology (RSM). The optimum removal conditions were determined at pH 4, contact time 90 minutes, weight of biosorbent 3000 mg/L, and size of biosorbent 0.4 mm. Color removal of 53.55% was demonstrated, the experimental data and model predictions agreed well. In the optimization, R2 and 2correlation coefficients for the quadratic model was estimated quite satisfactorily as 0.988 and 0.977, respectively.

scholarly journals Textile Wastewater Treatment for Water Reuse: A Case Study

Processes ◽  
2019 ◽  
Vol 7 (1) ◽  
pp. 34 ◽  
Author(s):  
Hua Yin ◽  
Peiwen Qiu ◽  
Yuange Qian ◽  
Zhuwen Kong ◽  
Xiaolong Zheng ◽  
...  
Keyword(s):  
Textile Industry ◽  
Water Reuse ◽  
Natural Waters ◽  
Removal Rate ◽  
Operating Cost ◽  
Textile Wastewater ◽  
Color Removal ◽  
Combined Processes ◽  
Sand Filtration ◽  
Drinking Water Standard

The reduced natural waters and the large amount of wastewater produced by textile industry necessitate an effective water reuse treatment. In this study, a combined two-stage water reuse treatment was established to enhance the quality and recovery rate of reused water. The primary treatment incorporated a flocculation and sedimentation system, two sand filtration units, an ozonation unit, an ultrafiltration (UF) system, and a reverse osmosis (RO) system. The second treatment included an ozonation unit, a sand filtration unit, and UF and RO systems. The color removal rate increased with the increasing ozone dosage, and the relational expression between the ozone dosage and color removal rate was fitted. Ozonation greatly reduced the color by 92.59 and 97.27 times during the primary and second ozonation stages, respectively. RO had the highest removal rate. The combined processes showed good performance in water reuse treatment. The treated, reused water satisfied the reuse standard and surpassed the drinking water standard rates for chemical oxygen consumption (CODcr), color, NH3-N, hardness, Cl−, SO42−, turbidity, Fe3+, and Cu2+. The operating cost of reuse water treatment was approximately 0.44 USD·m−3.

Is a sequencing batch biofilter granular reactor suitable for textile wastewater treatment?

2012 ◽  
Vol 66 (7) ◽  
pp. 1392-1398 ◽  
Author(s):  
A. M. Lotito ◽  
U. Fratino ◽  
A. Mancini ◽  
G. Bergna ◽  
C. Di Iaconi
Keyword(s):  
Wastewater Treatment ◽  
Cost Reduction ◽  
Textile Industry ◽  
Biological Treatment ◽  
Textile Wastewater ◽  
Pollutant Load ◽  
Operational Conditions ◽  
Different Types ◽  
Textile Wastewater Treatment ◽  
Direct Discharge

The textile industry releases highly polluted and complex wastewaters, which are difficult to treat and require numerous treatment steps. Innovative technologies for on-site treatment at each factory would permit cost reduction. For this reason, we ran a laboratory-scale study to assess the suitability of a sequencing batch biofilter granular reactor (SBBGR) for textile wastewater treatment, testing four different types of wastewater. Results demonstrate that wastewater characteristics greatly affect the reactor efficiency. Hence, a pre-study is advisable to define the best operational conditions and the maximum treatment capability for the wastewater under analysis. Nevertheless, SBBGR is a valuable biological treatment, effective in the reduction of pollutant load with stable performances despite the variability in wastewater composition. Tests with ozone integration have demonstrated that it is possible to dose small quantities of ozone to obtain an effluent suitable for direct discharge. However, a dynamic ozone dosage should be used to optimize the process as the correct ozone dose strongly depends on the wastewater composition.

scholarly journals INVESTIGATION of COLOR REMOVAL in REAL TEXTILE INDUSTRY WASTEWATER with MEMBRANE BIOREACTOR-ACTIVE CARBON SYSTEM

2021 ◽  
pp. 18-21
Author(s):  
Nurtaç Öz ◽  
Meryem Yılmaz ◽  
Ahmet Çelebi
Keyword(s):  
Activated Carbon ◽  
Active Carbon ◽  
Textile Industry ◽  
Membrane Bioreactor ◽  
High Efficiency ◽  
Textile Wastewater ◽  
Color Removal ◽  
Color Measurement ◽  
Pollution Level ◽  
Carbon System

The textile industry is an industry that consumes large amounts of water during production, contains various chemicals in its wastewater, conventional treatment methods are insufficient to reduce the wastewater pollution level, and has colloidal substances and color problems. Membrane bioreactor systems provide high efficiency in the treatment of textile wastewater and dyestuff removal. Removal of dyestuffs and turbidity in real textile wastewater by using a laboratory-scale membrane bioreactor system was studied. Chemical precipitation was not applied before the biological treatment for the removal of color and other pollutant parameters. A hollow fiber microfiltration membrane module was used in the system. Then a combination with an active carbon filter was created to take the color removal to a higher level. The development of the microorganism composition adapted to the textile industry was observed in the biological reactor. The system was operated with an endless sludge age and a hydraulic retention time of 24 hours. Color measurement transparency index parameter DFZ (DurchsichtsFarbZahl) was measured in a spectrophotometer at wavelengths of 436, 525, and 620 nm (nanometers) according to EN ISO 7887 standards. In the microfiltration permeate water, the color removal were found in 436 nm: 91-95%, 525 nm: 94-98%, 620 nm: 96-99%, and in activated carbon permeate water, the color removal in 436 nm: 96-99% at 525 nm: 95-99%, 620 nm: 96-99%, respectively. Due to the physical separation of the membrane, which is the simplest definition, high efficiencies in color removal have been achieved in the system. The activated carbon system combined with the membrane was found higher efficiency in color removal than the microfiltration output.

scholarly journals Comparative Studies of Using Nano Zerovalent Iron, Activated Carbon, and Green Synthesized Nano Zerovalent Iron for Textile Wastewater Color Removal Using Artificial Intelligence, Regression Analysis, Adsorption Isotherm, and Kinetic Studies

2020 ◽  
Vol 13 ◽  
pp. 117862212090827 ◽  
Author(s):  
Ahmed Karam ◽  
Khaled Zaher ◽  
Ahmed S Mahmoud
Keyword(s):  
Regression Analysis ◽  
Activated Carbon ◽  
Contact Time ◽  
Textile Wastewater ◽  
Color Removal ◽  
Zerovalent Iron ◽  
X Ray ◽  
Stirring Rate ◽  
Nano Zerovalent Iron ◽  
Initial Color

Daily, a big extent of colored, partially treated textile effluents drained into the sanitation systems causing serious environmental concerns. Therefore, the decolorization treatment process of wastewater is crucial to improve effluent quality. In the present study, 3 different sorbent materials, nano zerovalent iron (nZVI), activated carbon (AC), and green-synthesized nano zerovalent iron (GT-nZVI), have been prepared for raw textile wastewater decolourization. The prepared nanomaterials were characterized via X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, and UV-Vis absorption spectroscopy. In addition, the effect of different operating parameters such as pH, contact time, and stirring rate on the color removal efficiency was extensively studied to identify the optimum removal conditions. The reaction temperature, adsorbent dose, and initial color concentration were fixed during the experiments at room temperature, 0.7 g/L, and 350 and 50 mg/L Pt/Co color unit, respectively. Moreover, adsorption and reaction kinetics were analyzed using different isotherms and models. For simulating the adsorption process, artificial neural network (ANN) data were compatible with the result of regression analysis derived from response surface methodology (RSM) optimization. Our results showed the higher ability of nZVI, AC, and GT-nZVI in textile wastewater color removal. At pH 5, contact time 50 minutes, and stirring rate 150 rpm, nZVI showed good color removal efficiency of about 71% and 99% for initial color concentrations of 350 and 50 mg/L Pt/Co color unit, respectively. While slightly higher color removal ability of about 72% and 100% was achieved by using AC at pH 8, contact time 70 minutes, and stirring rate 250 rpm. Finally, the largest ability of color removal about 85% and 100% was recorded for GT-nZVI at pH 7, contact time 40 minutes, and stirring rate 150 rpm. This work shows the enhanced color removal ability of GT-nZVI as a potential textile wastewater decolourization material, opening the way for many industrial and environmental applications.

scholarly journals Comparison of naturally prepared coagulants for removal of COD and color from textile wastewater

2013 ◽  
Vol 15 (4) ◽  
pp. 522-528 ◽  
Keyword(s):  
Textile Industry ◽  
Textile Wastewater ◽  
Color Removal ◽  
Volume Index ◽  
Percentage Reduction ◽  
Maize Seed ◽  
Sludge Volume Index ◽  
Maximum Percentage ◽  
Industrial Sectors ◽  
Flocculation Time

<p>The wastewater generated by the textile industry is rated as the most polluting among all industrial sectors considering both volumes discharged and effluent composition. Present investigation intended for COD and color removal from textile wastewater using naturally prepared coagulants i.e. Surjana Seed Powder (SSP), Maize Seed Powder (MSP) and Chitosan. Effect of coagulant dose, flocculation time and temperature has been studied. The Sludge Volume Index (SVI) and turbidity were examined for various effects. SSP was more effective than Chitosan and MSP for the removal of COD and color and also, Chitosan was more efficient than SSP and MSP considering SVI and turbidity. Maximum percentage reduction corresponds to 75.6 and 62.8 was obtained for removal of COD and color respectively using SSP.</p>

Sign in / Sign up

Export Citation Format

Share Document