Influence of PAC properties on membrane performance in a PAC-UF hybrid system

2012 ◽  
Vol 12 (4) ◽  
pp. 496-503 ◽  
Author(s):  
F. Saravia ◽  
C. Zwiener ◽  
F. H. Frimmel
Keyword(s):  
Activated Carbon ◽  
Transmembrane Pressure ◽  
Hybrid Processes ◽  
Membrane Performance ◽  
Membrane Flux ◽  
Flux Decline ◽  
Overall Performance ◽  
Selection Of ◽  
Better Than ◽  
Main Factor

The combination of ultrafiltration (UF) and powdered activated carbon (PAC) has gained in importance over the last 15 years. The aim of applying PAC-UF hybrid processes is to improve the rejection capacity and the performance of membrane processes. In this work the influence of PAC-addition on membrane flux decline and fouling formation was studied with a submerged module using different water matrices. The PACs used were characterized by measurements of the surface area, the particle size distribution and the surface charge to get a better understanding of the observed effects. Results showed that the membrane flux decline was dependent on the applied type of activated carbon. When adding Picachem 8P, the transmembrane pressure (TMP) increased very quickly and the membrane performance was even worse than that without PAC. However, when adding Norit SA-UF under identical filtration conditions, the TMP was stable and the membrane performance was better than that without PAC. The fouling layers of the two PACs applied showed entirely different structures. Therefore the selection of a suitable PAC is a main factor for the overall performance of PAC-UF hybrid systems with submerged membranes.

Fouling of a polyethersulfone ultrafiltration membrane by natural organic matter

2004 ◽  
Vol 4 (4) ◽  
pp. 205-212 ◽  
Author(s):  
G. Makdissy ◽  
J.-P. Croué ◽  
G. Amy ◽  
H. Buisson
Keyword(s):  
Natural Organic Matter ◽  
Surface Waters ◽  
Membrane Fouling ◽  
Adsorption Mechanism ◽  
Transmembrane Pressure ◽  
Membrane Flux ◽  
Dead End ◽  
Flux Decline ◽  
Hydrophilic Fraction ◽  
Significant Flux

This research focused on membrane flux decline trends observed during ultrafiltration (UF) of solutions of NOM fractions isolated from surface waters. All filtration experiments were performed with a non-stirred dead-end cell unit equipped with flat sheet polyethersulfone PES UF membrane coupons under a constant transmembrane pressure of 1 bar. Results showed that the most significant flux decline was due to the organic colloid fraction, a hydrophilic fraction consisting mostly of bacterial cell wall residues. This research demonstrated that these colloids which incorporate 2/3 of dissolved organic structures (<0.45 μm) and 1/3 of particulate organics exert strong fouling properties due to both rejection phenomena and the adsorption mechanism. The fouling contribution by humic-like materials depends on their origin and nature. Aromaticity appears to be a secondary parameter which influences membrane fouling. Polysaccharides, proteins and amino sugars also largely present in humic-like structures (supramolecular structure) play an important role in UF membrane fouling. The perspective of NOM as a biopolymer mixture can contribute to an understanding of membrane fouling.

scholarly journals FACTORS INFLUENCING STUDENTS’ SELECTION OF UNIVERSITIES: THE CASE OF OMAN

2018 ◽  
Vol 2 (2) ◽  
pp. 83
Author(s):  
Abdelghani Echchabi ◽  
Salim Al-Hajri
Keyword(s):  
Academic Staff ◽  
Mean Value ◽  
Academic Quality ◽  
Mean Values ◽  
University Reputation ◽  
University Selection ◽  
Overall Performance ◽  
The University ◽  
Selection Of ◽  
Main Factor

The main purpose of the study was to examine the factors that mostly influence students’ selection of the universities where they enrolled, in the Omani context. The study used mean values to rank the factors based on the students’ responses. The study covered a sample of 384 respondents from various Omani regions and used the mean value to examine the factors that influence students’ selection of their respective universities. The findings revealed that the main factor for university selection is the university reputation, followed by completion time, academic quality, as well as the academic staff qualifications. These findings have significant contributions to the Omani universities, as well universities in similar contexts. Particularly, it provides the universities with insights on the main dimensions and characteristics to emphasize in order to enhance their overall performance.

scholarly journals Analisis Kinerja Routing Protokol RIPng Dengan OSPFv3 Pada Jaringan IPV6 Tunneling

Petir ◽  
2018 ◽  
Vol 10 (2) ◽  
pp. 56-36
Author(s):  
Redaksi Tim Jurnal
Keyword(s):  
Data Packet ◽  
Test Results ◽  
Patch Selection ◽  
Test Bed ◽  
Literature Study ◽  
Overall Performance ◽  
The Many ◽  
Selection Of ◽  
Better Than

The main objective of the development ipv6 is to meet need of ip addresses for a long term and improving the existing weaknesses in ipv4. But the transitional of the protokol version 4 to protokol version 6 cant be done by casually because due to the many infrastructure of the ipv4 network have been installed . For it is needed method to integrate ipv4 with ipv6 and one of the method is to use tunneling. The presence of tunneling network also needed routing protokol that support ipv6 protokol such as ripng and ospfv3 in ipv6 tunneling network. This paper is arranged to determine the performance of ripng dan ospfv3 routing protokols by analyzing the patch selection of data transmission, routing update analysis, speed time convergent analysis, analyzing by sending tcp data packet and sniffing analysis of data packet in tunneling network. The method used is literature study, computer simulation, and implementation on the test-bed. Data analysis showed that performance of ospfv3 is better than ripng because the speed of convergent time is faster. Ospfv3 need an average time as musch as 19 seconds but ripng need 178 seconds.on the test results of network throughput for tcp windows size that have 2, 4, 5, 6 kbyte capacity it take an average 121, 58 mbit/sec for ospfv3 and 117, 44 mbit/sec for ripng. For the overall performance of ripng and ospfv3 are not much different from its predecessor routing protokol in ipv4 network, it just for ripng and ospfv3 have support for 128-bit ipv6 addressing.

A Comparison of Four Adolescent Language Tests

1987 ◽  
Vol 18 (3) ◽  
pp. 250-266 ◽  
Author(s):  
R. Jane Lieberman ◽  
Ann Marie C. Heffron ◽  
Stephanie J. West ◽  
Edward C. Hutchinson ◽  
Thomas W. Swem
Keyword(s):  
Test Performance ◽  
Sixth Grade ◽  
Significant Discrepancy ◽  
Language Impaired ◽  
Language Functions ◽  
Language Tests ◽  
Significant Difference ◽  
Sixth Grade Students ◽  
Overall Performance ◽  
Selection Of

Four recently developed adolescent language tests, the Fullerton Test for Adolescents (FLTA), the Test of Adolescent Language (TOAL), the Clinical Evaluation of Language Functions (CELF), and the Screening Test of Adolescent Language (STAL), were compared to determine: (a) whether they measured the same language skills (content) in the same way (procedures); and (b) whether students performed similarly on each of the tests. First, respective manuals were reviewed to compare selection of subtest content areas and subtest procedures. Then, each of the tests was administered according to standardized procedures to 30 unselected sixth-grade students. Despite apparent differences in test content and procedures, there was no significant difference in students' performance on three of the four tests, and correlations among test performance were moderate to high. A comparison of the pass/fail rates for overall performance on the tests, however, revealed a significant discrepancy between the proportions of students identified in need of further evaluation on the STAL (20%) and the proportion diagnosed as language impaired on the three diagnostic tests (60-73%). Clinical implications are discussed.

Implementasi Voip Server Berbasis IPV6 Dengan Raspberry PI

2019 ◽  
Vol 9 (01) ◽  
pp. 47-54
Author(s):  
Rabbai San Arif ◽  
Yuli Fitrisia ◽  
Agus Urip Ari Wibowo
Keyword(s):  
Internet Protocol ◽  
Wireless Transmission ◽  
Raspberry Pi ◽  
Test Results ◽  
Average Delay ◽  
Ipv6 Network ◽  
Ip Network ◽  
Selection Of ◽  
Better Than

Voice over Internet Protocol (VoIP) is a telecommunications technology that is able to pass the communication service in Internet Protocol networks so as to allow communicating between users in an IP network. However VoIP technology still has weakness in the Quality of Service (QoS). VOPI weaknesses is affected by the selection of the physical servers used. In this research, VoIP is configured on Linux operating system with Asterisk as VoIP application server and integrated on a Raspberry Pi by using wired and wireless network as the transmission medium. Because of depletion of IPv4 capacity that can be used on the network, it needs to be applied to VoIP system using the IPv6 network protocol with supports devices. The test results by using a wired transmission medium that has obtained are the average delay is 117.851 ms, jitter is 5.796 ms, packet loss is 0.38%, throughput is 962.861 kbps, 8.33% of CPU usage and 59.33% of memory usage. The analysis shows that the wired transmission media is better than the wireless transmission media and wireless-wired.

Effect of Contact Ratio on Spur Gear Dynamic Load With No Tooth Profile Modifications

1996 ◽  
Vol 118 (3) ◽  
pp. 439-443 ◽  
Author(s):  
Chuen-Huei Liou ◽  
Hsiang Hsi Lin ◽  
F. B. Oswald ◽  
D. P. Townsend
Keyword(s):  
Dynamic Load ◽  
Spur Gear ◽  
Tooth Size ◽  
Contact Ratio ◽  
Gear Dynamics ◽  
Wide Range ◽  
Gear Contact ◽  
Center Distance ◽  
Selection Of ◽  
Better Than

This paper presents a computer simulation showing how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented in this paper was performed by using the NASA gear dynamics code DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low-contact-ratio gears (contact ratio less than two), increasing the contact ratio reduced gear dynamic load. For high-contact-ratio gears (contact ratio equal to or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high-contact-ratio gears minimized dynamic load better than low-contact-ratio gears.

scholarly journals Performance Evaluation of IMERG GPM Products during Tropical Storm Imelda

Atmosphere ◽  
2021 ◽  
Vol 12 (6) ◽  
pp. 687
Author(s):  
Salman Sakib ◽  
Dawit Ghebreyesus ◽  
Hatim O. Sharif
Keyword(s):  
Stage Iv ◽  
Tropical Storm ◽  
Average Correlation ◽  
Acceptable Range ◽  
Precipitation Estimates ◽  
Overall Performance ◽  
Early Late ◽  
Statistical Metrics ◽  
Better Than

Tropical Storm Imelda struck the southeast coastal regions of Texas from 17–19 September, 2019, and delivered precipitation above 500 mm over about 6000 km2. The performance of the three IMERG (Early-, Late-, and Final-run) GPM satellite-based precipitation products was evaluated against Stage-IV radar precipitation estimates. Basic and probabilistic statistical metrics, such as CC, RSME, RBIAS, POD, FAR, CSI, and PSS were employed to assess the performance of the IMERG products. The products captured the event adequately, with a fairly high POD value of 0.9. The best product (Early-run) showed an average correlation coefficient of 0.60. The algorithm used to produce the Final-run improved the quality of the data by removing systematic errors that occurred in the near-real-time products. Less than 5 mm RMSE error was experienced in over three-quarters (ranging from 73% to 76%) of the area by all three IMERG products in estimating the Tropical Storm Imelda. The Early-run product showed a much better RBIAS relatively to the Final-run product. The overall performance was poor, as areas with an acceptable range of RBIAS (i.e., between −10% and 10%) in all the three IMERG products were only 16% to 17% of the total area. Overall, the Early-run product was found to be better than Late- and Final-run.

scholarly journals Insights in Behavior of Variably Formulated Alginate-Based Microcapsules for Cell Transplantation

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
Pia Montanucci ◽  
Silvia Terenzi ◽  
Claudio Santi ◽  
Ilaria Pennoni ◽  
Vittorio Bini ◽  
...  
Keyword(s):  
Divalent Cations ◽  
Chemical Properties ◽  
Live Cells ◽  
High Performing ◽  
Physical Chemical ◽  
Degenerative Disorders ◽  
Selection Of ◽  
Better Than

Alginate-based microencapsulation of live cells may offer the opportunity to treat chronic and degenerative disorders. So far, a thorough assessment of physical-chemical behavior of alginate-based microbeads remains cloudy. A disputed issue is which divalent cation to choose for a high performing alginate gelling process. Having selected, in our system, high mannuronic (M) enriched alginates, we studied different gelling cations and their combinations to determine their eventual influence on physical-chemical properties of the final microcapsules preparation,in vitroandin vivo. We have shown that used of ultrapure alginate allows for high biocompatibility of the formed microcapsules, regardless of gelation agents, while use of different gelling cations is associated with corresponding variable effects on the capsules’ basic architecture, as originally reported in this work. However, only the final application which the capsules are destined to will ultimately guide the selection of the ideal, specific gelling divalent cations, since in principle there are no capsules that are better than others.

scholarly journals Pilot Study on the Combination of Different Pre-Treatments with Nanofiltration for Efficiently Restraining Membrane Fouling While Providing High-Quality Drinking Water

Membranes ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 380
Author(s):  
Yan Chen ◽  
Huiping Li ◽  
Weihai Pang ◽  
Baiqin Zhou ◽  
Tian Li ◽  
...  
Keyword(s):  
Drinking Water ◽  
Activated Carbon ◽  
Membrane Fouling ◽  
Membrane Surface ◽  
Post Treatment ◽  
Size Exclusion ◽  
Transmembrane Pressure ◽  
Feed Water ◽  
High Quality ◽  
Treated Water

Nanofiltration (NF) is a promising post-treatment technology for providing high-quality drinking water. However, membrane fouling remains a challenge to long-term NF in providing high-quality drinking water. Herein, we found that coupling pre-treatments (sand filtration (SF) and ozone–biological activated carbon (O3-BAC)) and NF is a potent tactic against membrane fouling while achieving high-quality drinking water. The pilot results showed that using SF+O3-BAC pre-treated water as the feed water resulted in a lower but a slowly rising transmembrane pressure (TMP) in NF post-treatment, whereas an opposite observation was found when using SF pre-treated water as the feed water. High-performance size-exclusion chromatography (HPSEC) and three-dimensional excitation–emission matrix (3D-EEM) fluorescence spectroscopy determined that the O3-BAC process changed the characteristic of dissolved organic matter (DOM), probably by removing the DOM of lower apparent molecular weight (LMW) and decreasing the biodegradability of water. Moreover, amino acids and tyrosine-like substances which were significantly related to medium and small molecule organics were found as the key foulants to membrane fouling. In addition, the accumulation of powdered activated carbon in O3-BAC pre-treated water on the membrane surface could be the key reason protecting the NF membrane from fouling.

scholarly journals Effectiveness of cartographic presentation methods applied within small-scale thematic maps in the press and on the Internet

2015 ◽  
Vol 47 (1) ◽  
pp. 5-17
Author(s):  
Jolanta Korycka-Skorupa
Keyword(s):  
Graphic Design ◽  
Small Scale ◽  
The Internet ◽  
Thematic Maps ◽  
The Press ◽  
Presentation Methods ◽  
Written Word ◽  
Selection Of ◽  
Better Than

Abstract The author discuss effectiveness of cartographic presentations. The article includes opinions of cartographers regarding effectiveness, readability and efficiency of a map. It reminds the principles of map graphic design in order to verify them using examples of small-scale thematic maps. The following questions have been asked: Is the map effective? Why is the map effective? How do cartographic presentation methods affect effectiveness of the cartographic message? What else can influence effectiveness of a map? Each graphic presentation should be effective, as its purpose is to complete written word, draw the recipients’ attention, make text more readable, expose the most important information. Such a significant role of graphics results in the fact that graphic presentations (maps, diagrams) require proper preparation. Users need to have a chance to understand the graphics language in order to draw correct conclusions about the presented phenomenon. Graphics should demonstrate the most important elements, some tendencies, and directions of changes. It should generalize and present a given subject from a slightly different perspective. There are numerous examples of well-edited and poorly edited small-scale thematic maps. They include maps, which are impossible to interpret correctly. They are burdened with methodological defects and they cannot fulfill their task. Cartography practice indicates that the principles related to graphic design of cartographic presentation are frequently omitted during the process of developing small-scale thematic maps used – among others – in the press and on the Internet. The purpose of such presentations is to quickly interpret them. On such maps editors’ problems with the selection of an appropriate symbol and graphic variable (fig. 1A, 9B) are visible. Sometimes they use symbols which are not sufficiently distinguishable nor demonstrative (fig. 11), it does not increase their readability. Sometime authors try too hard to reflect presented phenomenon and therefore the map becomes more difficult to interpret (fig. 4A,B). The lack of graphic sense resulting in the lack of graphic balance and aesthetics constitutes a weak point of numerous cartographic presentations (fig. 13). Effectiveness of cartographic presentations consists of knowledge and skills of the map editor, as well as the recipients’ perception capabilities and their readiness to read and interpret maps. The qualifications of the map editor should include methodological qualifications supported by the knowledge of the principles for cartographic symbol design, as well as relevant technical qualifications, which allow to properly use the tools to edit a map. Maps facilitate the understanding of texts they accompany and they present relationships between phenomenon better than texts, appealing to the senses.

Sign in / Sign up

Export Citation Format

Share Document