scholarly journals Effect of bubble characteristics and nozzle size on the membrane distillation enhanced by gas–liquid two-phase flow

2019 ◽  
Vol 9 (3) ◽  
pp. 292-300
Author(s):  
Dashuai Zhang ◽  
Xiaopeng Zhang ◽  
Li Chen ◽  
Wang Lili ◽  
Wu Di ◽  
...  
Keyword(s):  
Gas Flow ◽  
Membrane Surface ◽  
Threshold Level ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
High Concentration ◽  
Two Phase ◽  
Flux Enhancement ◽  
Nozzle Size ◽  
Sweeping Gas

Abstract This study investigates the membrane performance and fouling control in bubble-assisted sweeping gas membrane distillation with high concentration saline (333 K saturated solution) as feed. The results show that a longer bubbling interval (3 min) at a fixed bubbling duration of 30 s can most efficiently increase the flux enhancement ratio up to 1.518. Next, the flux increases with the gas flow rate under a relatively lower level, but tends to plateau after the threshold level (1.2 L·min−1). Compared to the non-bubbling case, the permeate flux reaches up to 1.623-fold at a higher bubble relative humidity of 80%. It was also found that greater flux enhancement can be achieved and, meanwhile, dramatic flux decline can be delayed for an intermittent bubbling system with a smaller nozzle size. These results accord well with the observations of fouling deposition in situ on the membrane surface with scanning electron microscope (SEM).

scholarly journals Effect of on the Membrane Distillation of PVDF Membrane Material Enhanced by Gas-Liquid Two-Phase Flow

2018 ◽  
Vol 2 (1) ◽  
Keyword(s):  
Membrane Surface ◽  
Threshold Level ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
High Concentration ◽  
Two Phase ◽  
Flux Enhancement ◽  
Membrane Performance ◽  
Flux Decline ◽  
Sweeping Gas

This study investigates the membrane performance and fouling control in the bubble-assisted sweeping gas membrane distillation with high concentration saline (333 K saturated solution) as feed. The results show that longer bubbling interval (3 min) at a fixed bubbling duration of 30s can most efficiently increase the the flux enhancement ratio up to 1.518. Next, the flux increases with the gas flowrate under a relatively lower level, but tends to a plateau after the threshold level (1.2 L•min-1). Compared to non-bubbling case, the permeate flux reaches up to 1.623 fold at a higher bubble relative humidity of 80 %. It was also found that greater flux enhancement can be achieved and meanwhile dramatic flux decline can be delayed for an intermittent bubbling system with a smaller nozzle size. These results accord well with the observations of fouling deposition in situ on the membrane surface with SEM.

scholarly journals Concentrating of Sugar Syrup in Bioethanol Production Using Sweeping Gas Membrane Distillation

Membranes ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 59 ◽  
Author(s):  
Mohammad A. Shirazi ◽  
Ali Kargari
Keyword(s):  
Flow Rate ◽  
Gas Flow ◽  
Design Method ◽  
Membrane Distillation ◽  
Green Technology ◽  
Bioethanol Production ◽  
Permeate Flux ◽  
Operating Variables ◽  
Glucose Syrup ◽  
Sweeping Gas

Membrane distillation (MD) is a relatively new and underdeveloped separation process which can be classified as a green technology. However, in order to investigate its dark points, sensitivity analysis and optimization studies are critical. In this work, a number of MD experiments were performed for concentrating glucose syrup using a sweeping gas membrane distillation (SGMD) process as a critical step in bioethanol production. The experimental design method was the Taguchi orthogonal array (an L9 orthogonal one) methodology. The experimental results showed the effects of various operating variables, including temperature (45, 55, and 65 °C), flow rate (200, 400, and 600 ml/min) and glucose concentration (10, 30, and 50 g/l) of the feed stream, as well as sweeping gas flow rate (4, 10, and 16 standard cubic feet per hour (SCFH)) on the permeate flux. The main effects of the operating variables were reported. An ANOVA analysis showed that the most and the least influenced variables were feed temperature and feed flow rate, each one with 62.1% and 6.1% contributions, respectively. The glucose rejection was measured at 99% for all experiments. Results indicated that the SGMD process could be considered as a versatile and clean process in the sugar concentration step of the bioethanol production.

scholarly journals A Systematic Framework for Optimizing a Sweeping Gas Membrane Distillation (SGMD)

Membranes ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 254
Author(s):  
Nawras N. Safi ◽  
Salah. S. Ibrahim ◽  
Nasser Zouli ◽  
Hasan Shaker Majdi ◽  
Qusay F. Alsalhy ◽  
...  
Keyword(s):  
Flow Rate ◽  
Gas Flow ◽  
Membrane Distillation ◽  
Feed Flow Rate ◽  
Permeate Flux ◽  
Gas Flow Rate ◽  
Feed Concentration ◽  
Sweeping Gas ◽  
Feed Temperature ◽  
Systematic Framework

The present work has undertaken a meticulous glance on optimizing the performance of an SGMD configuration utilized a porous poly (vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) membrane. This was carried out by conducting a systematic framework for investigating and optimizing the pertinent parameters such as sweeping gas flow rate, feed temperature, feed concentration and feed flow rate on the permeate flux. For this purpose, the Taguchi method and design of experiment techniques were harnessed to statistically determine optimum operational conditions. Besides that, a comprehensive surface and permeation characterization was conducted against the hand-made membranes. Results showcased that the membrane performance was ultimately controlled by the feed temperature and was nearly (~680) % higher when the temperature raised from 45 to 65 °C. Also, to a lesser extent, the system was dominated by the feed flow rate. As the adopted feed flow rate increases (from 0.2 to 0.6 L/min), around 47.5% increment was bestowed on water permeability characteristics. In contra, 34.5% flux decline was witnessed when higher saline feed concentration (100 g/L) was utilized. In the meantime, with raising the sweeping gas flow rate (from 120 to 300 L/h), the distillate was nearly 129% higher. Based on Taguchi design, the maximum permeate flux (17.3 and 17 kg/m2·h) was secured at 35 g/L, 0.4 L/min, 65 °C and 300 L/h, for both commercial and prepared membranes, respectively.

Analysis of shear stress and energy consumption in a tubular airlift membrane system

2011 ◽  
Vol 64 (1) ◽  
pp. 189-198 ◽  
Author(s):  
N. Ratkovich ◽  
C. C. V. Chan ◽  
P. R. Berube ◽  
I. Nopens
Keyword(s):  
Shear Stress ◽  
Energy Consumption ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Membrane Surface ◽  
Phase Flow ◽  
Permeate Flux ◽  
Flow Conditions ◽  
Two Phase ◽  
Cake Layer

Application of a two-phase slug flow in side-stream membrane bioreactors (MBRs) has proven to increase the permeate flux and decrease fouling through a better control of the cake layer. Past literature has shown that the hydrodynamics near the membrane surface have an impact on the degree of fouling by imposing high shear stress near the surface of the membrane. Previously, shear stress histograms (SSH) have been introduced to summarize results from an experimental setup developed to investigate the shear stress imposed on the surface of a membrane under different two-phase flow conditions (gas and liquid) by varying the flow of each phase. Bimodal SSHs were observed, with peaks corresponding to the shear induced by the liquid and gas flow respectively. In this contribution, SSHs are modelled using simple empirical relationships. These are used to identify the two-phase flow conditions that optimize fouling control. Furthermore, the total energy consumption of the system was estimated based on the two-phase pressure drop. It was found that low liquid and high gas flow rates (ratio of approx. 4) balanced the peaks and minimized the energy consumption.

scholarly journals Concentration of FeSO4 spent solutions by membrane distillation

2007 ◽  
Vol 9 (2) ◽  
pp. 15-18 ◽  
Author(s):  
Marek Gryta
Keyword(s):  
Potential Application ◽  
Ph Value ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Salt Solutions ◽  
Iron Compounds ◽  
Fast Decline ◽  
Waste Salt

Concentration of FeSO4 spent solutions by membrane distillation The possibility of potential application of membrane distillation for the concentration of waste salt solutions has been presented in this work. It was found that the oxidation of iron compounds takes place during the process that was associated with the formation of a layer of oxides on the membrane surface. A fast decline of the permeate flux was observed due to the scaling phenomena. The problem of scaling was eliminated by the acidification with H2SO4 of the feed to the pH value of 2.

The new concept of flux enhancement during cell separation with MF/UF processes

2001 ◽  
Vol 1 (5-6) ◽  
pp. 381-386
Author(s):  
A. Kołtuniewicz
Keyword(s):  
Cell Separation ◽  
High Efficiency ◽  
Membrane Surface ◽  
Cross Flow ◽  
Dry Mass ◽  
High Energy ◽  
Process Conditions ◽  
Permeate Flux ◽  
Flux Enhancement ◽  
Flow Systems

The microfiltration and ultrafiltration processes are considered as matured membrane processes that are well established in industrial practice. Nevertheless, the main obstacles of their further development in the new competitive implementations are the economical problems. The key economic factors are permeate flux and energy consumption. However, although the cross-flow systems enable us to attain higher flux, it is usually very expensive. The high energy is consumed to maintain circulation velocity of the retentate that is sufficient for sweeping out the retained component from the membrane surface. Moreover in the case of cells separation the high intensity of the fouling and low cake permeability makes it necessary to apply additional efforts, such as backflushing, backpulsing, promoters of turbulence, vibrations, ultrasounds and many other. Therefore, dead-end systems are still quite competitive with cross-flow, especially for diluted (less than 0.5% of dry mass) suspensions or solutions. Cell separation with membranes is one of the most vivid problems for modern biotechnology, wastewater and water treatment. Membranes offer mild process conditions and high selectivity of separation. This enables us to solve a variety of problems such as cell culturing, fractionation, concentration, purification and sterilisation. The selected cells may be precisely separated from other components of broth and subsequently directed into the reaction space again in good conditions to ensure a quasi-continuous mode of operation. Moreover, membranes enable us to attain high efficiency of the bioconversion by removal of all product and inhibitors directly from the bioreactor. This is the reason for the huge interest in cell separation with membranes. The idea of the paper was to present the new concept of flux enhancement for cell separation on membranes. This concept lies in taking advantage of the specific rheological nature of biopolymers, which are the main foulants. The biopolymers retained on the membrane surface (i.e. on the top layer) can be applied as a lubricant for the cells that can settle on such a ‘movable layer’. As is shown, further in the paper, the thickness of the moving layer is lower and the flux is greater. The common movement of the cells and gel layer is very convenient from the cells integrity point of view. However the hydrodynamic conditions always play an important role in cross-flow systems; the resistance of ultrafiltration membranes may be reduced much more when compared with more open microfiltration membranes.

Influence of humic acid on the long-term performance of direct contact membrane distillation

2018 ◽  
Vol 30 (1) ◽  
pp. 109-120 ◽  
Author(s):  
Dong-Wan Cho ◽  
Gihoon Kwon ◽  
Jeongmin Han ◽  
Hocheol Song
Keyword(s):  
Humic Acid ◽  
Membrane Fouling ◽  
Coalbed Methane ◽  
Direct Contact ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Permeate Flux ◽  
Direct Contact Membrane Distillation ◽  
High Level

In this study, the influence of humic acid on the treatment of coalbed methane water by direct contact membrane distillation was examined with bench-scale test unit. During short-term distillation (1000 min), high level of humic acid above 50 ppm resulted in significant decrease in permeate flux, while low level of humic acid (∼2 ppm) had little influence on the flux. For the long-term distillation (5000 min), the flux decline began at 3400 min in the presence of 5 ppm humic acid and 5 mM Ca2+, and decreased to ∼40% of initial flux at 5000 min. The spectroscopic analysis of the membrane used revealed that the surface was covered by hydrophilic layers mainly composed of calcite. The membrane fouling effect of humic acid became more significant in the presence of Ca2+ due to more facile calcite formation on the membrane surface. It was demonstrated that humic acid enhanced CaCO3 deposition on the membrane surfaces, thereby expediting the scaling phenomenon.

Experimental Study and Numerical Simulation of the Air Gap Membrane Distillation (AGMD) Process

2016 ◽  
Vol 11 (1) ◽  
pp. 41-45 ◽  
Author(s):  
Ehsan Karbasi ◽  
Javad Karimi-Sabet ◽  
J. Mohammadi Roshandeh ◽  
M. A. Moosavian ◽  
H. Ahadi
Keyword(s):  
Numerical Simulation ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Air Gap ◽  
Operating Conditions ◽  
Permeate Flux ◽  
Air Gap Membrane Distillation ◽  
Temperature Polarization ◽  
Output Ratio ◽  
Cfd Method

Abstract Some challenges, including inappropriate distribution of currents on the membrane surface, poor hydrodynamics and existing severe temperature polarization (TP) phenomenon in MD modules, impede industrialization of MD process. Computational fluid dynamics (CFD) method was used for numerical simulation of hydrodynamics in air gap membrane distillation modules. One of two simulated modules in this work is a novel developed one in which heat and mass transfer data was compared with available literature data. Moreover, the effect of using baffles in module was investigated. Comparison between the novel module and conventional module indicates higher trans-membrane mass flux and gained output ratio (GOR) coefficient by 7% and 15%, respectively. Moreover, the effects of different operating conditions including feed temperatures and feed flow rates on permeate flux were investigated.

Chemical pretreatment of feed water for membrane distillation

2008 ◽  
Vol 62 (1) ◽  
Author(s):  
Marek Gryta
Keyword(s):  
Membrane Fouling ◽  
Membrane Surface ◽  
Membrane Distillation ◽  
Feed Water ◽  
Chemical Pretreatment ◽  
Permeate Flux ◽  
Membrane Scaling ◽  
Water Pretreatment ◽  
Energy Dispersion Spectrometry ◽  
Process Operation

AbstractMembrane distillation was used to produce demineralized water from ground water. The influence of feed water pretreatment carried out in a contact clarifier (softening with Ca(OH)2 and coagulation with FeSO4 · 7H2O) followed by filtration, on the process effectiveness was evaluated. It was found that the chemical pretreatment decreased the membrane fouling; however, the degree of water purification was insufficient because precipitation of small amounts of deposit on the membrane surface during the process operation was still observed. The permeate flux was gradually decreasing as a result of scaling. The morphology and composition of the fouling layer were studied using scanning electron microscopy coupled with energy dispersion spectrometry. The presence of significant amounts of silica, apart from calcium and magnesium, was determined in the formed deposit. The removal of foulants by heterogeneous crystallization performed inside the filter (70 mesh), assembled directly at the module inlet, was found to be a solution preventing the membrane scaling.

Sign in / Sign up

Export Citation Format

Share Document