scholarly journals Water polishing of phenol by walnut green hull as adsorbent: an insight of adsorption isotherm and kinetic

2016 ◽  
Vol 6 (4) ◽  
pp. 544-552 ◽  
Author(s):  
H. Godini ◽  
F. Hashemi ◽  
L. Mansuri ◽  
M. Sardar ◽  
Ghasem Hassani ◽  
...  
Keyword(s):  
Langmuir Isotherm ◽  
Surface Characteristics ◽  
Xrd Analysis ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Sorption ◽  
Pseudo Second Order ◽  
Xrd Techniques

The present paper aims to investigate water purification of phenol by walnut green hull adsorbent. The surface characteristics of the adsorbent were studied using Fourier transform infra-red (FTIR), scanning electron microscope, and X-ray diffraction (XRD) techniques. The presence of functional groups such as hydroxyl and carbonyl onto walnut green hull surface was proved by FTIR analysis. Also quartz, cellulose and hematite were detected in the XRD analysis of samples by an X-ray diffractometer. The maximum sorption was achieved at pH 4.0. Data were evaluated for compliance with the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. The results indicate that the data for adsorption of phenol onto walnut green hull fitted well with the Langmuir isotherm. The maximum adsorption capacity of the adsorbent was achieved by Langmuir isotherm 17.8 mg g–1. Also, the adsorption kinetics of phenol on the adsorbent were studied. The rates of sorption were found to conform to pseudo-second-order kinetics with good correlation.

Efficient adsorption of chlorpyrifos onto modified activated carbon by gamma irradiation; a plausible adsorption mechanism

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mohamed S. Yahia ◽  
Ahmed S. Elzaref ◽  
Magdy B. Awad ◽  
Ahmed M. Tony ◽  
Ahmed S. Elfeky
Keyword(s):  
Gamma Irradiation ◽  
Area Measurement ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
First Order ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Pseudo First Order ◽  
Kinetics Of

Abstract Commercial Granulated Active Carbon (GAC) has been modified using 10 Gy dose Gamma irradiation (GAC10 Gy) for increasing its ability of air purification. Both, the raw and treated samples were applied for removing Chlorpyrifos pesticide (CPF) from ambient midair. Physicochemical properties of the two materials were characterized by Fourier Transform Infrared (FT-IR) and Raman spectroscopy. The phase formation and microstructure were monitored using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), supported with Energy-Dispersive X-ray (EDX). The Surface area measurement was detected using BET particle size prosometry. Obtained outcomes showed that, the maximum adsorption capacity, given by Langmuir equations, was greatly increased from 172.712 to 272.480 mg/g for GAC and GAC10 Gy, respectively, with high selectivity. The overall removal efficiency of GAC10 Gy was notably comparable to that of the original GAC-sorbent. The present study indicated that, gamma irradiation could be a promising technique for treating GAC and turned it more active in eliminating the pesticides pollutants from surrounding air. The data of equilibrium has been analyzed by Langmuir and Freundlich models, that were considerably better suited for the investigated materials than other models. The process kinetics of CPF adsorbed onto both tested carbon versions were found to obey the pseudo first order at all concentrations with an exception at 70 mg/l using GAC, where, the spontaneous exothermic adsorption of Chlorpyrifos is a strong function for the pseudo-first order (PFO) and pseudo second order (PSO) kinetics.

scholarly journals The Removal of Uranium and Thorium from Their Aqueous Solutions by 8-Hydroxyquinoline Immobilized Bentonite

Minerals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 626 ◽  
Author(s):  
Salah ◽  
Gaber ◽  
Kandil
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Langmuir Isotherm ◽  
Freundlich Isotherm ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The sorption of uranium and thorium from their aqueous solutions by using 8-hydroxyquinoline modified Na-bentonite (HQ-bentonite) was investigated by the batch technique. Na-bentonite and HQ-bentonite were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier Transform Infrared (FTIR) spectroscopy. Factors that influence the sorption of uranium and thorium onto HQ-bentonite such as solution pH, contact time, initial metal ions concentration, HQ-bentonite mass, and temperature were tested. Sorption experiments were expressed by Freundlich and Langmuir isotherms and the sorption results demonstrated that the sorption of uranium and thorium onto HQ-bentonite correlated better with the Langmuir isotherm than the Freundlich isotherm. Kinetics studies showed that the sorption followed the pseudo-second-order kinetic model. Thermodynamic parameters such as ΔH°, ΔS°, and ΔG° indicated that the sorption of uranium and thorium onto HQ-bentonite was endothermic, feasible, spontaneous, and physical in nature. The maximum adsorption capacities of HQ-bentonite were calculated from the Langmuir isotherm at 303 K and were found to be 63.90 and 65.44 for U(VI) and Th(IV) metal ions, respectively.

Removal of acetaminophen (ACT) from aqueous solution by using nanosilica adsorbent: experimental study, kinetic and isotherm modeling

2020 ◽  
Vol 49 (1) ◽  
pp. 55-62
Author(s):  
Akbar Eslami ◽  
Zahra Goodarzvand Chegini ◽  
Maryam Khashij ◽  
Mohammad Mehralian ◽  
Marjan Hashemi
Keyword(s):  
Removal Rate ◽  
Synthesis Method ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Content Type ◽  
Bet Analysis ◽  
Pseudo Second Order

Purpose A nanosilica adsorbent was prepared and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET. Design/methodology/approach The optimum conditions for the highest adsorption performance were determined by kinetic modeling. The adsorbent was used for the adsorption of acetaminophen (ACT), and the parameters affecting the adsorption were discussed like pH, initial concentration, contact time and adsorbent dosage. The adsorbent have been characterized by SEM, XRD and BET analysis. The kinetic models including pseudo-first-order and pseudo-second-order with Langmuir and Freundlich isotherm models were applied to investigate the kinetic and isotherms parameters. Findings The adsorption of ACT increased to around 95% with the increase of nanosilica concentration to 30 g/L. Moreover, the adsorption process of ACT follows the pseudo-second-order kinetics and the Langmuir isotherm with the maximum adsorption capacity of 609 mg/g. Practical implications This study provided a simple and effective way to prepare of nanoadsorbents. This way was conductive to protect environmental and subsequent application for removal of emerging pollutants from aqueous solutions. Originality/value The novelty of the study is synthesizing the morphological and structural properties of nanosilica-based adsorbent (specific surface area, pore volume and size, shape and capability) and improving its removal rate through optimizing the synthesis method; and studying the capability of synthesis of nanosilica-based adsorbent for removal of ACT as a main emerging pharmaceutical water contaminant.

scholarly journals Sequestration of Pb(II) Ions from Aqueous Systems with Novel Green Bacterial Cellulose Graphene Oxide Composite

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 218 ◽  
Author(s):  
Alfred Mensah ◽  
Pengfei Lv ◽  
Christopher Narh ◽  
Jieyu Huang ◽  
Di Wang ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Bacterial Cellulose ◽  
Kinetic Studies ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Carboxylate Groups ◽  
Green Adsorbent ◽  
Pseudo Second Order ◽  
Very High

In this study, a novel green adsorbent material prepared by the esterification of bacterial cellulose (BC) and graphene oxide (GO), richly containing hydroxyl, alkyl, and carboxylate groups was characterised by FTIR (Fourier Transform infrared spectroscopy), XRD (X-ray diffraction), SEM (Scanning electron microscopy) and TGA (Thermo-graphimetric analysis). The specific surface area (SSA) and pore size distribution (PSD) analysis of materials were also analysed. Batch experiments–adsorption studies confirmed the material to have a very high Pb2+ removal efficiency of over 90% at pH 6–8. Kinetic studies showed that the uptake of metal ions was rapid with equilibrium attained after 30 min and fitted well with the pseudo-second-order rate model (PSO). Isotherm results with a maximum adsorption capacity (Qmax) of 303.03 mg/g were well described by Langmuir’s model compared to Freundlich. Desorption and re-adsorption experiments realised that both adsorbent and adsorbates could be over 90–95% efficiently recovered and reused using 0.1 M HNO3 and 0.1 M HCl.

scholarly journals Mechanosynthesis of MFe2O4 (M = Co, Ni, and Zn) Magnetic Nanoparticles for Pb Removal from Aqueous Solution

2016 ◽  
Vol 2016 ◽  
pp. 1-9 ◽  
Author(s):  
America R. Vazquez-Olmos ◽  
Mohamed Abatal ◽  
Roberto Y. Sato-Berru ◽  
G. K. Pedraza-Basulto ◽  
Valentin Garcia-Vazquez ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Xrd Analysis ◽  
Maximum Adsorption Capacity ◽  
Sorption Behavior ◽  
Order Kinetic ◽  
X Ray ◽  
Isotherm Adsorption ◽  
Crystallite Sizes ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

Adsorption of Pb(II) from aqueous solution using MFe2O4 nanoferrites (M = Co, Ni, and Zn) was studied. Nanoferrite samples were prepared via the mechanochemical method and were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), micro-Raman, and vibrating sample magnetometry (VSM). XRD analysis confirms the formation of pure single phases of cubic ferrites with average crystallite sizes of 23.8, 19.4, and 19.2 nm for CoFe2O4, NiFe2O4, and ZnFe2O4, respectively. Only NiFe2O4 and ZnFe2O4 samples show superparamagnetic behavior at room temperature, whereas CoFe2O4 is ferromagnetic. Kinetics and isotherm adsorption studies for adsorption of Pb(II) were carried out. A pseudo-second-order kinetic describes the sorption behavior. The experimental data of the isotherms were well fitted to the Langmuir isotherm model. The maximum adsorption capacity of Pb(II) on the nanoferrites was found to be 20.58, 17.76, and 9.34 mg·g−1 for M = Co, Ni, and Zn, respectively.

scholarly journals Removal of Cesium and Strontium From Radioactive Wastewater by Prussian Blue Nanorods

2022 ◽  
Author(s):  
Chuqing Yao ◽  
Yaodong Dai ◽  
Shuquan Chang ◽  
Haiqian Zhang
Keyword(s):  
Prussian Blue ◽  
Photoelectron Spectroscopy ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Radioactive Wastewater ◽  
Pseudo Second Order ◽  
Co Precipitation ◽  
Solvothermal Methods

Abstract In this work, novel Prussian blue tetragonal nanorods were prepared by template-free solvothermal methods for removal of radionuclide Cs and Sr. It was worth that Prussian blue nanorods exhibited the better adsorption performance than co-precipitation PB or Prussian blue analogue composites. Thermodynamic analysis implied that adsorption process was spontaneous and endothermic which was described well with Langmuir isotherm and pseudo-second-order equation, the maximum adsorption capacity of PB nanorod was estimated to be 194.26 mg g-1 and 256.62 mg g-1 for Cs+ and Sr2+. The adsorption mechanism of Cs+ and Sr2+ was studied by X-ray photoelectron spectroscopy, X-ray diffraction and 57Fe Mössbaure spectroscopy, the results revealed that Cs+ entered in PB crystal to generate a new phase, the most of Sr2+ was trapped in internal crystal and the other exchanged Fe2+. Furthermore, the effect of co-existing ions and pH for PB adsorption process were also investigated. The results suggest that PB nanorods were outstanding candidate for removal of Cs+ and Sr2+ from radioactive wastewater.

Adsorption of 2,4,6-trichlorophenol on bentonite modified with benzyldimethyltetradecylammonium chloride

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Infrared Spectroscopy ◽  
Contact Time ◽  
Removal Rate ◽  
Organic Pollutant ◽  
Freundlich Isotherm ◽  
Solution Concentration ◽  
Isotherm Models ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pseudo Second Order

The objective of this study is to evaluate the performance and capacities of the bentonite of Maghnia, modified with benzyldimethyltetradecylammonium chloride, to remove the organic pollutant 2,4,6-Trichlorophenol (TCP). The modified sample was studied by X-ray diffraction (XRD) technique, infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA) methods. The best removal rate (99.52%) was obtained at 19°C, pH 4, solution concentration of 50 mg/L, stirring speed of 180 rpm and contact time of 60 min. The results were well fitted by both Langmuir and Freundlich isotherm models and the pseudo-second-order is the best model to describe the process.

Preparation of copper aluminum-biochar composite as adsorbent of malachite green in aqueous solution

2020 ◽  
Author(s):  
Neza Rahayu Palapa ◽  
Tarmizi Taher ◽  
Risfidian Mohadi ◽  
Addy Rachmat ◽  
Aldes Lesbani
Keyword(s):  
Aqueous Solution ◽  
Composite Material ◽  
Malachite Green ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Pseudo Second Order ◽  
Edx Analyses ◽  
Copper Aluminum ◽  
Regeneration Study

Abstract In this work, CuAl/Biochar (BC) composite was prepared by the coprecipitation method. The materials were applied to remove malachite green in aqueous solution. These materials were characterized using XRD, FTIR, BET and SEM-EDX analyses. The composite material was confirmed by X-ray diffractograms with reflection (002) at 24o and the appearance of new peaks at 1095 cm -1 . The BET result of CuAl/BC composite has larger surface area is 168 m 2 /g than 46 m 2 /g for LDH. The morphologies of composite materials show agglomeration and micro particle size. The result of the adsorption study indicated the composite material follows pseudo-second-order (PSO) and Langmuir isotherm models. The maximum adsorption capacity of malachite green using CuAl/BC uptake is 164.316 mg/g. The thermodynamic analysis indicates that the malachite green adsorption is spontaneous, endothermic. Regeneration study of adsorbent CuAl/BC composite shows after four times reused, it still has high removal efficiency at 89%.

scholarly journals Thermal behavior of Zefreh dolomite mine (Central Iran)

2009 ◽  
Vol 45 (1) ◽  
pp. 35-44 ◽  
Author(s):  
B.K. Shahraki ◽  
B. Mehrabi ◽  
R. Dabiri
Keyword(s):  
Thermal Behavior ◽  
Raw Materials ◽  
Atmospheric Condition ◽  
Xrd Analysis ◽  
Heating Time ◽  
X Ray Diffraction ◽  
Quartz Content ◽  
X Ray ◽  
Structure Changes ◽  
Xrd Techniques

Dolomite has a large amounts of MgO and is an important raw materials for steel, iron and refractory industries. In this paper thermal behavior of Zefreh dolomite at various temperatures was studied by differential thermal analysis (DTA), Thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT - IR) and powder X-ray diffraction (XRD) techniques. The DTA curve shows two endothermic peaks at 772 and 834?C. The first peak is associated with the formation of magnesia (MgO), calcite(CaCO3) and CO2. The second peak represents the decomposition of calcite with formation of CaO and further CO2 release. At 772?C quantitative XRD analysis in atmospheric condition shows small amounts of CaO (less than 2%) which form simultaneously or later than calcite. TGA curve shows total weight loss for decomposition of dolomite is 46.2%. By increasing heating time of samples in furnace, dolomite decomposes in lower temperatures. X-ray diffraction analysis of heat treated samples up to 750?C indicates that dolomite structure changes into calcite. The increases in quartz content accelerated the mechanochemical deformation and amorphization of dolomite phase. At high temperature ( more than 1000?C) Ca3Mg(SiO4)2 and CaSiO4 were formed. XRD and FTIR confirm dolomite decomposition reactions.

scholarly journals LDH Nanocubes Synthesized with Zeolite Templates and Their High Performance as Adsorbents

Nanomaterials ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 3315
Author(s):  
Moftah Essa Elkartehi ◽  
Rehab Mahmoud ◽  
Nabila Shehata ◽  
Ahmed Farghali ◽  
Shimaa Gamil ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Average Pore Size ◽  
Second Order ◽  
Polluted Water ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Average Pore ◽  
X Ray ◽  
Pseudo Second Order

In this work, the efficiency of the adsorptive removal of the organic cationic dye methylene blue (MB) from polluted water was examined using three materials: natural clay (zeolite), Zn-Fe layered double hydroxide (LDH), and zeolite/LDH composite. These materials were characterized via X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray (EDX) diffraction (XRF), low-temperature N2 adsorption, pore volume and average pore size distribution and field emission scanning electron microscopy (FE-SEM). The properties of the applied nanomaterials regarding the adsorption of MB were investigated by determining various experimental parameters, such as the contact time, initial dye concentration, and solution pH. In addition, the adsorption isotherm model was estimated using the Langmuir, Freundlich, and Langmuir–Freundlich isotherm models. The Langmuir model was the best-fitting for all applied nanomaterials. In addition, the kinetics were analyzed by using pseudo-first-order, pseudo-second-order, and intraparticle diffusion models, and the pseudo-second-order model was an apparent fit for all three applied nanomaterials. The maximum Adsorption capacity toward MB obtained from the materials was in the order zeolite/LDH composite > zeolites > Zn-Fe LDH. Thus, the zeolite/LDH composite is an excellent adsorbent for the removal of MB from polluted water.

Sign in / Sign up

Export Citation Format

Share Document