scholarly journals Characterization of secondary treated effluents for tertiary membrane filtration and water recycling

2012 ◽  
Vol 2 (2) ◽  
pp. 74-83 ◽  
Author(s):  
C. Ayache ◽  
M. Pidou ◽  
W. Gernjak ◽  
Y. Poussade ◽  
J.-P. Croué ◽  
...  
Keyword(s):  
Water Quality ◽  
Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Low Pressure ◽  
Hollow Fibre ◽  
Feed Water ◽  
Chemical Cleaning ◽  
Characterization Methods ◽  
Secondary Effluents

This study evaluates the impacts of water quality from three different secondary effluents on low pressure membrane fouling. Effluent organic matter (EfOM) has been reported by previous studies as responsible for membrane fouling. However, the contribution of the different components of EfOM to membrane fouling is still not well understood. In order to improve and optimize treatment processes, characterization and quantification of the organic matter are important. The characterization methods used in this study are liquid chromatography coupled with an organic detector (LC-OCD) and excitation emission matrix fluorescence spectroscopy (EEM). A bench-scale hollow fibre membrane system was used to identify the type of fouling depending on the feed water quality. Results showed no measurable dissolved organic carbon removal by the membranes for the three secondary effluents. Biopolymers and humic-like substances found in different proportions in the three effluents were partially retained by the membranes and were identified to contribute significantly to the flux decline of the low pressure membranes. The observed fouling was determined to be reversible by hydraulic backwashing for two effluents and only by chemical cleaning for the third effluent.

Natural organic matter fouling and chemical cleaning of nanofiltration membranes

2004 ◽  
Vol 4 (5-6) ◽  
pp. 245-251 ◽  
Author(s):  
Q. Li ◽  
M. Elimelech
Keyword(s):  
Water Quality ◽  
Organic Matter ◽  
Natural Organic Matter ◽  
Calcium Ions ◽  
Ionic Composition ◽  
Solution Chemistry ◽  
Feed Water ◽  
Cleaning Efficiency ◽  
Chemical Cleaning ◽  
Water Quality Control

Fouling and subsequent chemical cleaning are two important issues for sustainable operation of nanofiltration (NF) membranes in water quality control applications. Because fouling strongly depends on the feed water quality, especially the ionic composition, chemical cleaning solutions should be chosen to target the solution chemistry that is most responsible for the formation of a compact, high resistance fouling layer. In this study, the effect of solution chemistry on natural organic matter (NOM) fouling of two NF membranes with different surface properties was investigated. Compared to monovalent cations, divalent cations were found to greatly enhance NOM fouling by complexation. Moreover, calcium ions caused a much greater fouling rate than magnesium ions, presumably due to the intermolecular bridging formed among NOM molecules through the calcium ions. Various chemical cleaning solutions were evaluated for water flux recovery efficiency. Although both deionized water and dilute NaOH solution were found effective in cleaning membranes fouled in the absence of calcium ions, efficient chemical cleaning in presence of calcium was achieved only when the calcium ion bridging was eliminated. The cleaning efficiency was shown to be highly dependent on solution pH and the concentration of the chemical cleaning agent.

Leading the City of Baltimore into the 21st Century: Flexible Treatment Solutions and Integrated Raw Water Management

2010 ◽  
Vol 5 (4) ◽  
Author(s):  
J. L. Manuszak ◽  
M. MacPhee ◽  
S. Liskovich ◽  
L. Feldsher
Keyword(s):  
Water Management ◽  
Water Quality ◽  
Water Supply ◽  
Conceptual Design ◽  
Membrane Filtration ◽  
Treatment Plant ◽  
Low Pressure ◽  
Management Tool ◽  
Raw Water ◽  
The City

The City of Baltimore, Maryland is one of many US cities faced with challenges related to increasing potable water demands, diminishing fresh water supplies, and aging infrastructure. To address these challenges, the City recently undertook a $7M study to evaluate water supply and treatment alternatives and develop the conceptual design for a new 120 million gallon per day (MGD) water treatment plant. As part of this study, an innovative raw water management tool was constructed to help model source water availability and predicted water quality based on integration of a new and more challenging surface water supply. A rigorous decision-making approach was then used to screen and select appropriate treatment processes. Short-listed treatment strategies were demonstrated through a year-long pilot study, and process design criteria were collected in order to assess capital and operational costs for the full-scale plant. Ultimately the City chose a treatment scheme that includes low-pressure membrane filtration and post-filter GAC adsorption, allowing for consistent finished water quality irrespective of which raw water supply is being used. The conceptual design includes several progressive concepts, which will: 1) alleviate treatment limitations at the City's existing plants by providing additional pre-clarification facilities at the new plant; and 2) take advantage of site conditions to design and operate the submerged membrane system by gravity-induced siphon, saving the City significant capital and operations and maintenance (O&M) costs. Once completed, the new Fullerton Water Filtration Plant (WFP) will be the largest low-pressure membrane plant in North America, and the largest gravity-siphon design in the world.

Coagulation/flocculation/ultrafiltration for natural organic matter removal in drinking water production

2004 ◽  
Vol 4 (5-6) ◽  
pp. 215-222 ◽  
Author(s):  
A.R. Costa ◽  
M.N. de Pinho
Keyword(s):  
Drinking Water ◽  
Organic Matter ◽  
Natural Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Surface ◽  
Water Production ◽  
Cellulose Acetate Membranes ◽  
Wide Range ◽  
Drinking Water Production

Membrane fouling by natural organic matter (NOM), namely by humic substances (HS), is a major problem in water treatment for drinking water production using membrane processes. Membrane fouling is dependent on membrane morphology like pore size and on water characteristics namely NOM nature. This work addresses the evaluation of the efficiency of ultrafiltration (UF) and Coagulation/Flocculation/UF performance in terms of permeation fluxes and HS removal, of the water from Tagus River (Valada). The operation of coagulation with chitosan was evaluated as a pretreatment for minimization of membrane fouling. UF experiments were carried out in flat cells of 13.2×10−4 m2 of membrane surface area and at transmembrane pressures from 1 to 4 bar. Five cellulose acetate membranes were laboratory made to cover a wide range of molecular weight cut-off (MWCO): 2,300, 11,000, 28,000, 60,000 and 75,000 Da. Severe fouling is observed for the membranes with the highest cut-off. In the permeation experiments of raw water, coagulation prior to membrane filtration led to a significant improvement of the permeation performance of the membranes with the highest MWCO due to the particles and colloidal matter removal.

scholarly journals Removal Characteristics of N-Nitrosamines and Their Precursors by Pilot-Scale Integrated Membrane Systems for Water Reuse

2018 ◽  
Vol 15 (9) ◽  
pp. 1960 ◽  
Author(s):  
Haruka Takeuchi ◽  
Naoyuki Yamashita ◽  
Norihide Nakada ◽  
Hiroaki Tanaka
Keyword(s):  
Membrane Fouling ◽  
Water Reuse ◽  
Pilot Scale ◽  
Feed Water ◽  
Water Reclamation ◽  
Size Distributions ◽  
Membrane Systems ◽  
Chemical Cleaning ◽  
Ro Membrane ◽  
Feed Water Temperature

This study investigated the removal characteristics of N-Nitrosamines and their precursors at three pilot-scale water reclamation plants. These plants applies different integrated membrane systems: (1) microfiltration (MF)/nanofiltration (NF)/reverse osmosis (RO) membrane; (2) sand filtration/three-stage RO; and (3) ultrafiltration (UF)/NF and UF/RO. Variable removal of N-Nitrosodimethylamine (NDMA) by the RO processes could be attributed to membrane fouling and the feed water temperature. The effect of membrane fouling on N-Nitrosamine removal was extensively evaluated at one of the plants by conducting one month of operation and chemical cleaning of the RO element. Membrane fouling enhanced N-Nitrosamine removal by the pilot-scale RO process. This finding contributes to better understanding of the variable removal of NDMA by RO processes. This study also investigated the removal characteristics of N-Nitrosamine precursors. The NF and RO processes greatly reduced NDMA formation potential (FP), but the UF process had little effect. The contributions of MF, NF, and RO processes for reducing FPs of NDMA, N-Nitrosopyrrolidine and N-Nitrosodiethylamine were different, suggesting different size distributions of their precursors.

scholarly journals Optimization of In Situ Backwashing Frequency for Stable Operation of Anaerobic Ceramic Membrane Bioreactor

Processes ◽  
2020 ◽  
Vol 8 (5) ◽  
pp. 545 ◽  
Author(s):  
Rathmalgodage Thejani Nilusha ◽  
Tuo Wang ◽  
Hongyan Wang ◽  
Dawei Yu ◽  
Junya Zhang ◽  
...  
Keyword(s):  
Membrane Fouling ◽  
Membrane Filtration ◽  
Membrane Bioreactor ◽  
Ceramic Membrane ◽  
Pure Water ◽  
Ex Situ ◽  
Stable Operation ◽  
Chemical Cleaning ◽  
Cake Layer

The cost-effective and stable operation of an anaerobic ceramic membrane bioreactor (AnCMBR) depends on operational strategies to minimize membrane fouling. A novel strategy for backwashing, filtration and relaxation was optimized for stable operation of a side stream tubular AnCMBR treating domestic wastewater at the ambient temperature. Two in situ backwashing schemes (once a day at 60 s/day, and twice a day at 60 s × 2/day) maintaining 55 min filtration and 5 min relaxation as a constant were compared. A flux level over 70% of the initial membrane flux was stabilized by in situ permeate backwashing irrespective of its frequency. The in situ backwashing by permeate once a day was better for energy saving, stable membrane filtration and less permeate consumption. Ex situ chemical cleaning after 60 days’ operation was carried out using pure water, sodium hypochlorite (NaOCl), and citric acid as the order. The dominant cake layer was effectively reduced by in situ backwashing, and the major organic foulants were fulvic acid-like substances and humic acid-like substances. Proteobacteria, Firmucutes, Epsilonbacteria and Bacteroides were the major microbes attached to the ceramic membrane fouling layer which were effectively removed by NaOCl.

Reverse Osmosis Technology for Wastewater Reuse

1991 ◽  
Vol 24 (9) ◽  
pp. 215-227 ◽  
Author(s):  
B. J. Mariñas
Keyword(s):  
Water Quality ◽  
Reverse Osmosis ◽  
Membrane Fouling ◽  
Quality Parameters ◽  
Operating Conditions ◽  
Water Quality Parameters ◽  
Feed Water ◽  
Hydraulic Pressure ◽  
Predominant Component ◽  
Percent Removal

Reverse osmosis technology has a great potential in the field of wastewater reclamation. A reverse osmosis plant includes the following processes: (1) feed water microfiltration and chemical conditioning, (2) membrane treatment, (3) permeate aeration, neutralization and disinfection, and (4) concentrate (liquid residue) treatment and disposal. The performance of reverse osmosis membranes depends on operating conditions and water quality parameters. Permeate productivity and contaminant removals increase with applied hydraulic pressure. Water quality parameters such as concentration, composition and pH also affect contaminant removal efficiencies. For example, the treatment of a simulated wastewater containing 10 mg/L of nitrate with a commercial polyamide-type reverse osmosis membrane resulted in membrane permeates containing approximately 0.05 mg/L of nitrate (or 99.5 percent removal) when sodium chloride was the major dissolved solid present in the feed water, and 1 mg/L (or 90 percent removal) when sodium sulfate was the predominant component. The removals of weak electrolyte contaminants are affected by feed water pH. For example, the removal of boron by a cellulose acetate-type membrane was reported to be greater than 99 percent at a pH of approximately 11, and less than 30 percent at a pH of 7. The practice of pre-treatment processes such as microfiltration and chemical conditioning can minimize performance deterioration resulting from membrane fouling by inorganic precipitates, organic macromolecules and microorganisms (biofouling).

Characteristic of algogenic organic matter and its effect on UF membrane fouling

2011 ◽  
Vol 64 (8) ◽  
pp. 1685-1691 ◽  
Author(s):  
T. Li ◽  
B. Z. Dong ◽  
Z. Liu ◽  
W. H. Chu
Keyword(s):  
Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Size Exclusion ◽  
Fluorescence Excitation ◽  
Membrane Pore ◽  
Blue Green Algae ◽  
Flux Decline ◽  
Exclusion Chromatography ◽  
Hydrophilic Compound

Algogenic organic matter (AOM) was extracted from blue-green algae (cyanobacteria) and its characteristic was determined by various methods including high-pressure size-exclusion chromatography (HP-SEC), hydrophobic and hydrophilic fractionation, molecular weight (MW) fractionation and fluorescence excitation emission matrix (EEM). The results revealed that AOM was hydrophilic fractionation predominantly, accounting for 78%. The specific ultraviolet absorbance of AOM was 1.1 L/(mg m) only. The analysis for MW distribution demonstrated that organic matter greater than 30,000 MW accounted for over 40% and was composed of mostly neutral hydrophilic compound. EEM analyses revealed that protein-like and humic-substances existed in AOM. A test for membrane filtration exhibited that AOM could make ultrafiltration membrane substantial flux decline, which can be attributed to membrane pore clog caused by neutral hydrophilic compound with larger MW.

Membrane fouling propensity after adsorption as pretreatment in rainwater: a detailed organic characterisation

2008 ◽  
Vol 58 (8) ◽  
pp. 1535-1539 ◽  
Author(s):  
L. Sabina ◽  
B. Kus ◽  
H.-K. Shon ◽  
J. Kandasamy
Keyword(s):  
Molecular Weight ◽  
Organic Matter ◽  
Membrane Fouling ◽  
Membrane Filtration ◽  
Building Blocks ◽  
Fulvic Acids ◽  
Humic And Fulvic Acids ◽  
Removal Efficiencies ◽  
Hydrophilic Compounds ◽  
Hydrophobic Fraction

Organic characterisation in rainwater was investigated in terms of dissolved organic carbon (DOC) and molecular weight distribution (MWD) after powdered activated carbon (PAC) adsorption. PAC adsorption was used as pretreatment to membrane filtration to reduce membrane fouling. The MW of organic matter in rainwater used in this study was in the range of 43,000 Da to 30 Da. Each peak of organic matter consisted of biopolymers (polysaccharides and proteins), humic and fulvic acids, building blocks, low MW acids (hydrolysates of humic substances), low MW neutrals and amphiphilics. Rainwater contained the majority of hydrophilic compounds up to 72%. PAC adsorption removed 33% of total DOC. The removal efficiencies of the hydrophobic and hydrophilic fractions after PAC adsorption were 50% and 27%, respectively. PAC adsorption was found to preferentially remove the hydrophobic fraction. The majority of the smaller MW of 1,100 Da, 820 Da, 550 Da, 90 Da and 30 Da was removed after PAC adsorption. The MFI values decreased from 1,436 s/L2 to 147 s/L2 after PAC adsorption. It was concluded that PAC adsorption can be used as a pretreatment to membrane filtration with rainwater.

Sign in / Sign up

Export Citation Format

Share Document