scholarly journals Effects of chemical activating agents on physical properties of activated carbons – a commentary

2020 ◽  
Vol 15 (4) ◽  
pp. 863-876
Author(s):  
Fadina Amran ◽  
Muhammad Abbas Ahmad Zaini
Keyword(s):  
Physical Properties ◽  
Pore Size ◽  
Surface Area ◽  
Activated Carbons ◽  
Pollutant Removal ◽  
Operating Conditions ◽  
Surface Areas ◽  
Chemical Agents ◽  
Developed Surface ◽  
Surface Area Increase

Abstract Well-developed surface areas and porous structures that render high adsorption capacity are necessary for pollutant removal from wastewater by activated carbons. Activated carbons from natural resources, and agricultural and industrial waste materials are produced using chemical agents, including KOH, H3PO4, K2CO3, ZnCl2 and NaOH. This study is intended to highlight the effects of those agents on the physical properties of the activated carbons. The operating conditions, i.e., temperature, time and ratio, show an interplay towards the physical properties at varying degree. The yield, pore size, mesoporosity and surface area of activated carbons derived using different chemical agents correlate well with the impregnation ratio. Generally, the pore size, mesoporosity and surface area increase, while the yield decreases with increasing ratio (over a given range). Higher ratio and temperature are recommended for KOH, K2CO3 and NaOH activation, to endow activated carbons with greater surface area.

scholarly journals Investigation on physical activation of some Mongolian coals

2019 ◽  
Vol 20 (46) ◽  
pp. 24-28
Author(s):  
Batkhishig Damdin ◽  
Barnasan Purevsuren ◽  
Yuanli Zhang ◽  
Haizhen Sun ◽  
Ariunaa Alyeksandr ◽  
...  
Keyword(s):  
Pore Size ◽  
Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Physical Activation ◽  
Surface Areas ◽  
Adsorption Of Nitrogen

Activation characteristics of four different Mongolian coals were investigated. The coals were carbonized at temperatures of 550 °C and the obtained samples were activated by preheated steam. The pore size, pore volume and surface areas of all activated carbons (AC) have been determined by adsorption of nitrogen (N2) gas. The BET surface areas of Aduunchuluun (ACAC), Shivee Ovoo (SCAC), Baganuur (BCAC) coal and Ulaan Ovoo coals (UCAC) are 283, 205, 251 and 460 m2/g respectively. Langmuir surface area is 283 m2/g of ACAC, 230 m2/g of SCAC, 537 m2/g in UCAC and 254 m2/g in BCAC.

scholarly journals The Effects of Methane Storage Capacity Using Upgraded Activated Carbon by KOH

2018 ◽  
Vol 8 (9) ◽  
pp. 1596 ◽  
Author(s):  
Jung Park ◽  
Gi Lee ◽  
Sang Hwang ◽  
Ji Kim ◽  
Bum Hong ◽  
...  
Keyword(s):  
Surface Area ◽  
Storage Capacity ◽  
Activated Carbons ◽  
Chemical Activation ◽  
High Surface ◽  
Heat Of Adsorption ◽  
Low Grade ◽  
Surface Areas ◽  
Ch4 Adsorption ◽  
Ch4 Storage

In this study, a feasible experiment on adsorbed natural gas (ANG) was performed using activated carbons (ACs) with high surface areas. Upgraded ACs were prepared using chemical activation with potassium hydroxide, and were then applied as adsorbents for methane (CH4) storage. This study had three principal objectives: (i) upgrade ACs with high surface areas; (ii) evaluate the factors regulating CH4 adsorption capacity; and (iii) assess discharge conditions for the delivery of CH4. The results showed that upgraded ACs with surface areas of 3052 m2/g had the highest CH4 storage capacity (0.32 g-CH4/g-ACs at 3.5 MPa), which was over two times higher than the surface area and storage capacity of low-grade ACs (surface area = 1152 m2/g, 0.10 g-CH4/g-ACs). Among the factors such as surface area, packing density, and heat of adsorption in the ANG system, the heat of adsorption played an important role in controlling CH4 adsorption. The released heat also affected the CH4 storage and enhanced available applications. During the discharge of gas from the ANG system, the residual amount of CH4 increased as the temperature decreased. The amount of delivered gas was confirmed using different evacuation flow rates at 0.4 MPa, and the highest efficiency of delivery was 98% at 0.1 L/min. The results of this research strongly suggested that the heat of adsorption should be controlled by both recharging and discharging processes to prevent rapid temperature change in the adsorbent bed.

scholarly journals Insights into the influence of the pore size and surface area of activated carbons on the energy storage of electric double layer capacitors with a new potentially universally applicable capacitor model

2019 ◽  
Vol 21 (6) ◽  
pp. 3122-3133 ◽  
Author(s):  
Ruben Heimböckel ◽  
Frank Hoffmann ◽  
Michael Fröba
Keyword(s):  
Energy Storage ◽  
Pore Size ◽  
Surface Area ◽  
Double Layer ◽  
Electric Double Layer ◽  
Activated Carbons ◽  
Porous Carbons ◽  
Pore Sizes ◽  
Double Layer Capacitors ◽  
Electric Double Layer Capacitors

A new capacitor model that confirms the non-constant capacitive contribution of different pore sizes and provides the possibility of simulating the capacitance values of porous carbons.

Preparation And Characterization Of Ultra-Small Sized Metal And Semiconductor Particles In Sol-Gel Materials

1994 ◽  
Vol 346 ◽  
Author(s):  
Kyung Moon Choi ◽  
Kenneth J. Shea
Keyword(s):  
Pore Size ◽  
Surface Area ◽  
Sol Gel ◽  
High Vacuum ◽  
Particle Sizes ◽  
Transition Metal Clusters ◽  
Surface Areas ◽  
Sol Gel Process ◽  
Bridged Silsesquioxanes

ABSTRACTPoly(l,4-phenylene)-bridged and poly(1,6-hexylene)-bridged silsesquioxanes (PPS and HPS) were prepared by the sol-gel process. The surface areas and pore diameters of these porous xerogels were obtained by BET and BJH methods, respectively. These porous materials were used as a confinement matrix for the growth of small-sized semiconductor and transition metal clusters. Quantum-sized CdS particles in PPS (approximately 58+12 Â) and HPS (91+16 Â) matrices were prepared by first soaking the xerogel in a CdCl2 solution. Following a washing with water, a Na2S solution was then added. EDAX and electron diffraction techniques were used to identify the CdS particles. The particle sizes of CdS in PPS and HPS were determined by both UV measurements and from TEM images. Small-sized Cr clusters were prepared in dried xerogels by an internal doping method. Mixed Cr/CdS phases were also prepared by internal loading of a chromium metal precursor. Following deposition of CdS the xerogel was heated at 120 °C under high vacuum, resulting in formation of intimately mixed phases of Cr metal and CdS. Changes in morphology, in particular the surface area and pore size distribution were noted. A decrease in surface area and an increase in pore size were observed as a result of Cr metal deposition.

A Comparison of Methods for Determining Surface Areas of Carbon Black

1973 ◽  
Vol 46 (1) ◽  
pp. 192-203 ◽  
Author(s):  
R. A. Klyne ◽  
B. D. Simpson ◽  
M. L. Studebaker
Keyword(s):  
Carbon Black ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Surface Areas ◽  
Furnace Black ◽  
Area Increase ◽  
Experimental Errors ◽  
Specific Surface Areas ◽  
Surface Area Increase

Abstract 1. The various tint tests correlate with each other—it does not make much difference which of the three procedures is used. The discrimination between similar blacks is comparable. Specific surface areas obtained by the three methods are comparable and differences appear to be due to experimental errors. (Compare Figures 5–7). 2. Surface areas larger than some 90 to 100 m2/g cannot be reliably determined from tint strength measurements alone. 3. Structure exerts a pronounced effect on tint strength of furnace blacks, especially above 90 to 100 m2/g. Porosity and/or composition are apparently also variables which affect tinting strength. 4. Densichron reflectance on the dry carbon black can be used to estimate specific surface areas up to about 140 m2/g; but, since theabsoluteerrorincreases as the specific surface area increases, this method loses some of its reliability at values above about 110 m2/g. The relative error in reflectance determinations does not vary greatly over the furnace-black range. Densichron reflectance is influenced by composition, evidently due to composition-related differences in optical properties of the carbons. 5. In CTAB adsorption measurements, titration errors and handling errors tend to be rather constant for blacks of different surface area. Hence, CTAB permits better discrimination among blacks of small particle size. 6. The errors in Densichron reflectance surface area increase with specific surface area. Hence, the deviations between CTAB and reflectance surface area which are due to experimental error increase with the surface area of the sample.

Changes in the Microstructure of Plasma-Sprayed Yttria-Stabilized Zirconia Deposits during Simulated Operating Conditions

1997 ◽  
Author(s):  
J. Ilavsky ◽  
G.G. Long ◽  
A.J. Allen ◽  
C.C. Berndt ◽  
H. Herman
Keyword(s):  
Surface Area ◽  
Small Angle Neutron Scattering ◽  
Operating Conditions ◽  
Yttria Stabilized Zirconia ◽  
Pore Surface ◽  
Stabilized Zirconia ◽  
Heating Rates ◽  
Surface Areas ◽  
Time Changes ◽  
Plasma Sprayed

Abstract The microstructures of as-sprayed and thermally-cycled freestanding and on-substrate deposits of yttria-stabilized zirconia were studied using small-angle neutron scattering (SANS). The SANS analysis allows the interlamellar pores and the intralamellar cracks, which are the two dominant void systems in the microstructure, to be characterized separately. Whereas up to 20% of the void surface area in the as-sprayed deposits was found to be in the cracks, the thermally-cycled deposits contained only a negligible quantity of cracks. At the same time, changes in the pore surface areas between the lamellae (i.e., the interlamellar pores) were much smaller. As a result, the microstructure of the thermally-cycled deposits was much more anisotropic than the microstructure of the as-sprayed deposits. Varying the cooling and the heating rates did not significantly change the microstructure but varying the total time that the deposits were at high temperature did affect the evolution of the surface area. The presence or absence of a bond coat and substrate also did not measurably influence the results.

RSM Optimization for the Production of Activated Carbons from Para-Wood Residue

2016 ◽  
Vol 718 ◽  
pp. 100-104 ◽  
Author(s):  
Pichaya Nitnithiphrut ◽  
Rangsinee Pimsri ◽  
Varinrumpai Seithtanabutara
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Activated Carbons ◽  
Operating Conditions ◽  
Optimal Conditions ◽  
Wood Residue ◽  
Impregnation Ratio ◽  
Rsm Optimization

Para-wood residue was impregnated in 40% wt. of H3PO4 solution for 24 h before carbonization under different temperatures and times. The response surface methodology (RSM) based on Box-Behnken was applied to optimize the operating conditions in producing activated carbon with high specific surface area. The effects of three variables; impregnation ratio, carbonising temperature and time on the specific surface of activated carbons were investigated. The proposed model was almost in accordance with the experimental case with correlation efficient and of 0.9653 and 0.9029, respectively. The optimal conditions were found to be 6%wt. of impregnation ratio and carbonization at 400°C for 67.27 min. The predicted surface area of produced activated carbon under these optimal conditions determined by RSM was 1069.30 m2/g. Experimental validation at these conditions was observed of 978.95 m2/g which closely agreed with the predicted value. This obtained activated carbon structure composed of mesopores and micropores with the average pore diameter of 21.71°A. This study indicated the RSM based on Box-Behnken design was the effectively method to optimize the operating condition and maximize the specific surface area of produced activated carbons.

scholarly journals Some Surface Properties of Activated Carbons Prepared by Gasification with Different Gases

1997 ◽  
Vol 15 (9) ◽  
pp. 707-715 ◽  
Author(s):  
Amina A. Attia
Keyword(s):  
Carbon Dioxide ◽  
Surface Area ◽  
Water Vapour ◽  
Pore Volume ◽  
Activated Carbons ◽  
Total Pore Volume ◽  
Surface Areas ◽  
Adsorption Of Nitrogen ◽  
Adsorption Of Water ◽  
Different Gases

A non-activated carbon ‘D’ was obtained by carbonizing date pits at 773 K in a limited supply of air. Activated carbons were obtained by gasifying portions of ‘D’ with air at 773 K, carbon dioxide at 1123 K, or steam at 1173 K, all to different burn-offs between 15% and 60%. The adsorption of nitrogen at 77 K and of carbon dioxide at 298 K was investigated using a volumetric adsorption apparatus of a conventional type. The adsorption of water vapour at 298 K and the chemisorption of pyridine at 423 K was followed by means of quartz spring balances. Gasification with oxidizing gases increased the surface area and total pore volume, as measured by nitrogen or carbon dioxide adsorption. In most cases, comparable surface areas were measured by nitrogen and carbon dioxide. The adsorption of water vapour depended on the percentage burn-off and the gasification conditions. Chemisorption of pyridine at 423 K was found to be related to the chemistry of the surface rather than to the surface area or total pore volume.

Correlation of Physical Properties of Inorganic Carrier and Microbial Survival Rate

2006 ◽  
Vol 317-318 ◽  
pp. 793-796 ◽  
Author(s):  
Hyung Mi Lim ◽  
Seung Ho Lee ◽  
Jun Bo Park ◽  
Jin A Kwon ◽  
Yeon Su Yu
Keyword(s):  
Survival Rate ◽  
Physical Properties ◽  
Pore Size ◽  
Surface Area ◽  
Inorganic Materials ◽  
Ion Conductivity ◽  
Bet Surface Area ◽  
Lower Survival Rate ◽  
Microbial Survival ◽  
Soluble Ions

Physical properties of various inorganic materials have been measured in terms of pore size distribution and porosity, BET surface area by nitrogen adsorption, pH, ion conductivity, and concentration of ions after elution test. The microbial survival rate and their stability have been monitored in every 10 days during 120 days by dilution plating method. The correlations between physical property of the inorganic carrier and microbial survival rate have been examined for the better preparation of microbial fertilizer. Average size of pore, and concentration of soluble ions were unequivocal factors affecting on microbial survival rate but BET surface area, average porosity, and ion conductivity revealed the equivocal correlation with microbial survival rate. Higher concentration of soluble ions gives lower survival rate and inorganic carriers with high microbial survival rate seemed to have preferred range of pore size.

Sign in / Sign up

Export Citation Format

Share Document