scholarly journals Removal of water hardness using zeolite synthesized from Ethiopian kaolin by hydrothermal method

2018 ◽  
Vol 14 (1) ◽  
pp. 145-159 ◽  
Author(s):  
Tadele Assefa Aragaw ◽  
Adane Adugna Ayalew
Keyword(s):  
Adsorption Capacity ◽  
Hydrothermal Method ◽  
Contact Time ◽  
Low Cost ◽  
Infrared Spectrometry ◽  
Zeolite Synthesis ◽  
Batch Experiments ◽  
Water Softening ◽  
Scanning Calorimetry ◽  
Wide Range

Abstract The use of low cost materials in zeolite synthesis becomes an area of important interest in water softening. This research is aimed to utilize kaolin for zeolite synthesis with hydrothermal method. Mechanical, thermal chemical treatments of raw kaolin were used for zeolite synthesis. Fourier Transform Infrared Spectrometry (FTIR), AAS, XRD, surface area (BET), differential scanning calorimetry and TGA were used to characterize kaolin and zeolite and UV–VIS/spectrometer were used for adsorption capacity of ion exchange. Effect of contact time, pH solution and temperature of the solution were studied for batch experiments. XRD values indicated that the prepared material is showed as fully crystalline and primarily amorphous. Before and after hardness removal sample transmittance percentage intensity showed a wide range of difference. From this study, it can be deduced that Zeolite can be used as a low cost water softening agent. At room temperature, the residue is well with calcium and badly with magnesium, whereas affinity toward Mg ions increases to acceptable levels at 60 °C. The cation exchange capacity of zeolite was found to be dependent on contact time. The batch experiments of removing Ca2+ and Mg2+ show that the adsorption capacity of zeolite in calcium ion is higher affinity than magnesium ion.

scholarly journals The Novel Use of Saraca thaipingensis Leaf Powder as Potential Biosorbent Material for the Removal of Chromium(VI)

2015 ◽  
Vol 3 (3) ◽  
pp. 35-39
Author(s):  
Sannasi Palsan ◽  
Chai Swee Fern ◽  
Stephanie Bernardine ◽  
Lim Fan Shiang
Keyword(s):  
Heavy Metals ◽  
Particle Size ◽  
Contact Time ◽  
Low Cost ◽  
Peninsular Malaysia ◽  
The Novel ◽  
Batch Experiments ◽  
Chromium Vi ◽  
Removal Of Heavy Metals ◽  
Leaf Powder

Saraca thaipingensis or ‘Gapis’ tree, classified under the Fabaceae family is a native of Taiping; copious over Peninsular Malaysia and Southeast Asia. The withered and fallen dead leaves were collected from INTI International University’s garden walkway. To date, literature has yet to capture the use of S. thaipingensis tree parts or refuse as potential biosorbent material for the removal of heavy metals thus verifying the novelty of this study. Batch experiments were carried out with the leaf powder to study the effects of dosage, particle size and contact time towards Cr(VI) removal (%) at 1-100 mg/L. Results showed that Cr(VI) removal increased from 52.22% to 99.31% (p < 0.05) with increase in biosorbent dosage (0.005, 0.010, 0.015, 0.020, 0.025 and 0.050 g). The different particle size ranges tested were: 107-125, 126-150, 151-250, 251-500, and 501- 1000 ?m. Highest Cr(VI) removal of 99.53% was obtained with the 151-250 ?m particle size; further size decrease did not yield more removal (p > 0.05). The optimal Cr(VI) removal was recorded after 45 min (99.62%) and 90 min (99.76%) contact time (p > 0.05). Further characterization and optimization studies are being carried out to develop a novel, sustainable, low cost yet effective leaf powder based biosorbent material.

Phosphorus and Nitrogen Removal from Sewage by Modified Honeycomb Cinder

2013 ◽  
Vol 726-731 ◽  
pp. 2931-2935
Author(s):  
Qi Bin Liang ◽  
Yun Gen Liu ◽  
Kun Tian
Keyword(s):  
Nitrogen Removal ◽  
Phosphorus Removal ◽  
Contact Time ◽  
Low Cost ◽  
Ammonia Nitrogen ◽  
Domestic Sewage ◽  
Operating Conditions ◽  
Optimal Conditions ◽  
Batch Experiments ◽  
Adsorption Capacities

The study aimed at phosphorus and nitrogen removal by honeycomb cinder modified with Zinc chloride (ZnCl2). By bench-scale batch experiments, honeycomb cinders with different modification time and ZnCl2 dosage were modified and its adsorption capacities were evaluated by methylence blue as the adsorbate. Under the optimal modification conditions, large amount modified honeycomb cinders were prepared to remove the phosphorus and nitrogen from domestic sewage, which different operating conditions of honeycomb cinders dosage, and contact time were considered. The results show that removal efficiencies of total phosphate (TP), orthophosphate (PO43-P), total nitrogen (TN) and ammonia nitrogen (NH4+-N) could reach 89.9%, 96.7%, 18.9% and 23.3% under the optimal conditions, respectively. Modified honeycomb cinders might be an effective and low cost adsorbent for phosphorus removal.

Adsorption of Cadmium (II) from Aqueous Solutions by Peanut Shell Cellulose Modified with Carbon Disulphide

2013 ◽  
Vol 791-793 ◽  
pp. 24-27
Author(s):  
Qing Shan Pan ◽  
Dai Qi Li ◽  
Jian Qiang Li ◽  
Wei Liu ◽  
Mei Gui Ma ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Sodium Hydroxide Solution ◽  
Carbon Disulphide ◽  
Removal Rate ◽  
Low Cost ◽  
Cellulose Xanthate ◽  
Ion Concentration ◽  
Peanut Shell ◽  
Hydroxide Solution

Peanut shell Cellulose Xanthate (PCX) was prepared by reacting with carbon disulphide after mercerized by sodium hydroxide solution. The preparing conditions (hydroxide solution concentration, carbon disulphide dosage, temperature) were optimized in this study. And the effects of PCX amount and contact time on the removal of Cd (II) ion from aqueous solution was studied,the results indicated that when the initial Cd (II) ion concentration was 10mg/L, the adsorption capacity of PXC was high effective with the PCX amount was 1g/L and the contact time was 1.5h,the equilibrium adsorption capacity of PCX was 9.87 mg/g and the removal rate of Cd (II) ion was 98.72%.Then the regeneration capacities of PCX adsorbent was investigated, the results indicated that the removal rate of Cd (II) ion was more than 75% after regeneration. All the results indicated that the PCX can be used as a low cost but effective biosorbent for heavy metals remediation.

scholarly journals Adsorption Of Cd(II) Ions From Aqueous Solution By A Low-Cost Biosorbent Prepared From Ipomea Pes-Caprae Stem

2020 ◽  
Vol 9 (3) ◽  
pp. 197-206
Author(s):  
Thaharah Ramadhani ◽  
Faisal Abdullah ◽  
Indra Indra ◽  
Abrar Muslim ◽  
Suhendrayatna Suhendrayatna ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Optimal Condition ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Ph Values ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

The use of a low-cost biosorbent prepared from Ipomoea pes-caprae stem for the adsorption of Cd(II) ions from aqueous solution at different contact times, biosorbent sizes, pH values, and initial Cd(II) ions concentration solution was investigated. The biosorbent was analyzed using Fourier-transform infrared spectroscopy (FT-IR) to find important IR-active functional groups. A scanning electron microscope (SEM) was used to examine the biosorbent morphology. The experimental results showed the highest Cd(II) ions adsorption was 29.513 mg/g  under an optimal condition as initial Cd(II) ions concentration of 662.77 mg/L, 1 g dose, 80-min contact time, pH 5, 75 rpm of stirring speed, 1 atm, and 30 oC. Cd(II) ions' adsorption kinetics obeys the linearized pseudo-second-order kinetics (R2 = 0.996), and the adsorption capacity is based on the optimal condition, and the rate attained was 44.444 mg/g and 0.097 g/mg. Min, respectively. Besides, the adsorption isotherms were very well fitted by the linearized Langmuir isotherm model, and the monolayer adsorption capacity and pore volume determined was 30.121 mg/g and 0.129 L/mg, respectively. These results indicated the chemisorption nature

scholarly journals Biosorption of Cr(III) from aqueous solution using an agricultural by-product jute stick powder: Equilibrium and kinetic studies

2018 ◽  
Vol 9 (3) ◽  
pp. 202-212 ◽  
Author(s):  
Mohammad Nasir Uddin ◽  
Jahangir Alam ◽  
Syeda Rahimon Naher
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Metal Ion ◽  
Water Solution ◽  
Low Cost ◽  
Isotherm Models ◽  
Infrared Spectrometry ◽  
Order Kinetic ◽  
Adsorption Model ◽  
Experimental Conditions

The adsorption capacity of chromium(III) from synthetic waste water solution by a low cost biomaterial, Jute Stick Powder (JSP)was examined. A series of batch experiments were conducted at different pH values, adsorbent dosage and initial chromium concentration to investigate the effects of these experimental conditions. To analyze the metal adsorption on to the JSP, most common adsorption isotherm models were applied. To study the reaction rate, the kinetic and diffusion models were also applied. The morphological structure and variation of functional groups in the JSP before and after adsorption was examined by scanning electron microscope (SEM) and Fourier transform infrared spectrometry (FT-IR). Maximum chromium removal capacities of JSP was 84.34%with corresponding equilibrium uptake 8.4 mg/g from 50 mg/L of synthetic metal solution in 60 minutes of contact time at pH = 6.0 and 28 °C with continuous stirring at 180 rpm. The percent sorption of the biomass decreased with increasing concentration of metal ion but increased with decreasing pH, increasing contact time and adsorbent doses. Data for this study indicated a good correspondence with both isotherms of Langmuir and Freundlich isotherm. The analysis of kinetic indicated that Chromium was consistent with the second-order kinetic adsorption model. The rate of removal of Cr(III) ions from aqueous solution by JSP was found rapid initially within 5-30 minutes and reached in equilibrium in about 40 minutes. The investigation revealed that JSP, a low cost agricultural byproduct, was a potential adsorbent for removal of heavy metal ions from aqueous solution.

scholarly journals ISOTERM ADSORPSI FENOL OLEH LEMPUNG ALAM

2019 ◽  
Vol 7 (1) ◽  
pp. 029
Author(s):  
Nelly Wahyuni ◽  
Imelda H. Silalahi ◽  
Dina Angelina
Keyword(s):  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Freundlich Isotherm ◽  
Langmuir Adsorption Isotherm ◽  
Batch Experiments ◽  
Natural Clay ◽  
Langmuir Adsorption ◽  
Equilibrium Data ◽  
Initial Phenol Concentration

Abstrak Fenol merupakan polutan yang sangat berbahaya di lingkungan karena bersifat racun dan sulit terdegradasi oleh organisme pengurai. Lempung alam yang berasal dari Kecamatan Capkala, Kabupaten Bengkayang  akan dikaji penggunaannya sebagai adsorben fenol. Adsorpsi dilakukan dengan metoda batch pada variasi waktu kontal dan konsentrasi awal fenol. Data kesetimbangan adsorpsi diuji dengan isoterm Langmuir dan Freundlich. Hasil penelitian menunjukkan waktu kontak optimum adsorpsi adalah 4 jam. Proses adsorpsi fenol  oleh lempung alam  mengikuti model isoterm adsorpsi Langmuir dengan kapasitas adsorpsi sebesar 0,65mg/g. Kata Kunci: fenol, Freundlich, isoterm adsorpsi, Langmuir, lempung alamAbstract Phenol is a pollutant that is very dangerous in the environment because it is toxic and difficult to degrade by decomposing organisms. Natural clay from Capkala District, Bengkayang Regency will be studied as phenol adsorbent. Batch experiments were carried out by varying the parameters like contact time of adsorption and initial phenol concentration. The equilibrium data were tested with Langmuir and Freundlich isotherm. The results showed that the optimum contact time for adsorption was 4 hours. The process of adsorption of phenol by natural clay follows the Langmuir adsorption isotherm model with an adsorption capacity of 0.65mg/g.  Keywords: adsorption isotherm, Freundlich, natural clay, phenol, Langmuir.

scholarly journals Glyphosate adsorption by Eucalyptus camaldulensis bark-mediated char and optimization through response surface modeling

2019 ◽  
Vol 9 (7) ◽  
Author(s):  
Kamalesh Sen ◽  
Jayanta Kumar Datta ◽  
Naba Kumar Mondal
Keyword(s):  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Eucalyptus Camaldulensis ◽  
Zero Point ◽  
Isotherm Models ◽  
Multilayer Adsorption ◽  
Batch Mode ◽  
Initial Concentration ◽  
Glyphosate Herbicide

Abstract In this study, orthophosphoric acid-modified activated char was prepared from Eucalyptus camaldulensis bark (EBAC), and used for removing traces of [N-(phosphonomethyl)glycine] (glyphosate) herbicide from aqueous solution. The adsorption capacity was characterized by zero-point-charge pH, surface analysis, and Fourier transform infrared spectroscopy. Batch mode experiments were conducted to observe the effects of selected variables, namely dose, contact time, pH, temperature, and initial concentration, on adsorption capacity. Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm models were generated to describe the mechanisms involved in the multilayer adsorption process. The results show that high temperature enhanced the adsorption capacity of EBAC, with a temperature of 373 K yielding adsorption capacity (qmax) and Freundlich parameter (KF) of 66.76 mg g−1 and 9.64 (mg g−1) (L mg−1)−n, respectively. The thermodynamics study revealed entropy and enthalpy of −5281.3 J mol−1 and −20.416 J mol−1, respectively. Finally, glyphosate adsorption was optimized by the Box–Behnken model, and optimal conditions were recorded as initial concentration of 20.28 mg L−1, pH 10.18, adsorbent dose of 199.92 mg/50 mL, temperature of 303.23 K, and contact time of 78.42 min, with removal efficiency of 98%. Therefore, it can be suggested that EBAC could be used as an efficient, low-cost adsorbent for removal of glyphosate from aqueous solutions.

Mechanical, morphological, flamability and thermal properties of artificial wood plastic

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Emad S. Shafik ◽  
Medhat L. Tawfic ◽  
Adel F. Younan
Keyword(s):  
Maleic Anhydride ◽  
Flame Retardant ◽  
Coupling Agent ◽  
Low Cost ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Content Type ◽  
Wide Range ◽  
Efficient Coupling ◽  
Analytical Tools

Purpose The purpose of this study is to manufacture composites from sawdust and polymer high-density polyethylene (HDPE) with different loading from alum as natural and cheap flame retardant and subsequently characterized using standard analytical tools. Design/methodology/approach Artificial wood plastic composites (WPCs) were prepared by mixing HDPE with sawdust as a filler with constant ratio (2:1) using hot press. Polyethylene-graft-maleic anhydride (PE-g-MAH) used as a coupling agent between two parents of the composites with different ratios (2.5, 5, 7 and 10). Alum as a flame retardant was incorporated into HDPE with 5 phr polyethylene grafted with maleic anhydride (PE-g-MAH) with different ratios (10, 15 and 20). Flame retardant efficiency was investigated using differential scanning calorimetry, thermal gravimetric analysis and the technique of ASTM E162. Findings The results revealed that the composite containing 5 phr from (PE-g-MAH) exhibited higher mechanical properties and this proved that (PE-g-MAH) act as an efficient coupling agent using the aforementioned ratio. The results also revealed that incorporation of alum as a flame retardant increased the thermal stability of the composites. Originality/value Artificial WPCs are ecofriendly materials with a wide range of applications in the constructions field. Moreover, they have high mechanical and physical properties with low cost. Evaluate alum as a natural and cheap flame retardant.

scholarly journals Magnesium Filled Polylactic Acid (PLA) Material for Filament Based 3D Printing

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 719 ◽  
Author(s):  
Iulian Antoniac ◽  
Diana Popescu ◽  
Aurelian Zapciu ◽  
Aurora Antoniac ◽  
Florin Miculescu ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Vitamin E ◽  
Polylactic Acid ◽  
Manufacturing Process ◽  
Structural Integrity ◽  
Low Cost ◽  
Cruciate Ligament ◽  
Infrared Spectrometry ◽  
Scanning Calorimetry ◽  
Anterior Cruciate

The main objective of this research is to prove the viability of obtaining magnesium (Mg) filled polylactic acid (PLA) biocomposites as filament feedstock for material extrusion-based additive manufacturing (AM). These materials can be used for medical applications, thus benefiting of all the advantages offered by AM technology in terms of design freedom and product customization. Filaments were produced from two PLA + magnesium + vitamin E (α-tocopherol) compositions and then used for manufacturing test samples and ACL (anterior cruciate ligament) screws on a low-cost 3D printer. Filaments and implant screws were characterized using SEM (scanning electron microscopy), FTIR (fourier transform infrared spectrometry), and DSC (differential scanning calorimetry) analysis. Although the filament manufacturing process could not ensure a uniform distribution of Mg particles within the PLA matrix, a good integration was noticed, probably due to the use of vitamin E as a precursor. The results also show that the composite biomaterials can ensure and maintain implant screws structural integrity during the additive manufacturing process.

scholarly journals Steel slag as low-cost adsorbent for the removal of phenanthrene and naphthalene

2018 ◽  
Vol 36 (3-4) ◽  
pp. 1160-1177 ◽  
Author(s):  
Liyun Yang ◽  
Xiaoming Qian ◽  
Zhi Wang ◽  
Yuan Li ◽  
Hao Bai ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Low Cost ◽  
Steel Slag ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Batch Experiments ◽  
Obvious Effect ◽  
X Ray ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model

This study investigates the removal effectiveness and characteristics of phenanthrene and naphthalene using low-cost steel slag with batch experiments. The adsorption characteristics of steel slag were measured and analysed using X-ray fluorescence, X-ray diffraction, and Fourier transform infrared spectroscopy. The batch experiments investigated the effect of the time gradient, pH, and steel slag dosage gradient on the adsorption of the steel slag. The results show that with time and dosage of steel slag increased, the adsorption capacity of phenanthrene and naphthalene increased and gradually became balanced, but pH had no obvious effect on the adsorption of phenanthrene and naphthalene. The Langmuir isotherm model best describes the phenanthrene and naphthalene removal by the steel slag, which shows the adsorption occurring in a monolayer. The maximum adsorption capacity of the steel slag to phenanthrene and naphthalene is 0.043 and 0.041 mg/g, respectively. A pseudo-first-order kinetic model can better represent the adsorption of phenanthrene and naphthalene by steel slag. The research demonstrates that the steel slag has a certain adsorption capacity for phenanthrene and naphthalene.

Sign in / Sign up

Export Citation Format

Share Document