scholarly journals Interaction between the US Army Corps of Engineers and the Orleans Levee Board preceding the drainage canal wall failures and catastrophic flooding of New Orleans in 2005

Water Policy ◽  
2015 ◽  
Vol 17 (4) ◽  
pp. 707-723 ◽  
Author(s):  
J. David Rogers ◽  
G. Paul Kemp ◽  
H. J. Bosworth ◽  
Raymond B. Seed

The authors hope to correct any premature conclusions about the role of the pre-Katrina Orleans Levee Board (OLB) in the failure of the outfall drainage canals in New Orleans during the 2005 hurricane – conclusions that appear to have been based on inaccurate information and/or assumptions. With regard to the 17th Street and London Avenue Canals, the authors have not uncovered any information that would suggest that the OLB behaved irresponsibly in its duties. What is evident from the project record is that the Army Corps of Engineers recommended raising the canal floodwalls for the 17th Street Canal, but recommended gated structures at the mouths of the Orleans and London Avenue Canals because the latter plan was less expensive. The OLB convinced Congress to pass legislation that required the Corps to raise the floodwalls for all three canals. Furthermore, the Corps, in a separate attempt to limit project costs, initiated a sheet pile load test (E-99 Study), but misinterpreted the results and wrongly concluded that sheet piles needed to be driven to depths of only 17 feet (1 foot = 0.3048 meters) instead of between 31 and 46 feet. That decision saved approximately US$100 million, but significantly reduced overall engineering reliability.

1964 ◽  
Vol 1 (4) ◽  
pp. 215-226 ◽  
Author(s):  
W G Brown

Calculations using the Neumann solution (as modified by Aldrich) and thermal properties of soils (obtained by Kersten) show that the frost penetration depth for the same freezing index for essentially all soils with any moisture content and for dry sand and rock varies by a factor of about 2 to 1. The extremes calculated in this way bracket the experimentally determined design curve of the US Army Corps of Engineers and give it theoretical support. The theoretical calculations and additional experimental data are used as a basis for a small alteration in the slope of the design curve. This modified design curve is recommended for field use because of (1) inherent imperfections in existing theory and (2) practical limitations to precise specification of field conditions.


2015 ◽  
Vol 35 (2) ◽  
pp. 196-208 ◽  
Author(s):  
Julie Dean Rosati ◽  
Katherine Flynn Touzinsky ◽  
W. Jeff Lillycrop

2017 ◽  
Vol 8 (1) ◽  
pp. 125-151 ◽  
Author(s):  
Eric M Gagnet ◽  
John M Hoemann ◽  
James S Davidson

Over recent decades, three distinct methods have evolved that are currently being used to generate resistance functions for single-degree-of-freedom analyses of unreinforced masonry walls subjected to blast loading. The degree of differences in these resistance definitions depends on whether the wall is assumed to be simply supported or whether compression arching forces result from rotation restraint at the supports. The first method originated in the late 1960s as a result of both experimental and analytical research sponsored by the US Department of Defense. That method, referred to as the Wiehle method, is the basis of Unified Facilities Criteria 3-340-02 and other derived analytical software such as the Wall Analysis Code developed by the US Army Corps of Engineers, Engineer Research and Development Center. The second method is based on elastic mechanics and an assumed linear decay function that follows and is the basis of the widely used Single-Degree-of-Freedom Blast Effects Design Spreadsheets software distributed by the US Army Corps of Engineers, Protective Design Center. The third method is largely based on concrete and masonry behavioral theories developed by Paulay and Priestly in the early 1990s. This article systematically compares the resistance methodologies for arching and non-arching scenarios, demonstrates the implications by plugging the disparate resistance functions into blast load single-degree-of-freedom models, compares the analytical results to full-scale blast test results, and offers conclusions about the accuracy and efficacies of each method.


2021 ◽  
Author(s):  
Jennifer McAlpin ◽  
Jason Lavecchia

The Brunswick area consists of many acres of estuarine and marsh environments. The US Army Corps of Engineers District, Savannah, requested that the US Army Engineer Research and Development Center, Coastal and Hydraulics Laboratory, develop a validated Adaptive Hydraulics model and assist in using it to perform hydrodynamic modeling of proposed navigation channel modifications. The modeling results are necessary to provide data for ship simulation. The model setup and validation are presented here.


Sign in / Sign up

Export Citation Format

Share Document