scholarly journals RELIABILITY OF TWO STAIN REMOVAL REGIMES ON COLOR CHANGE OF CONTEMPORARY RESIN-BASED RESTORATIVE MATERIALS IN VITRO STUDY

2016 ◽  
Vol 62 (1) ◽  
pp. 493-504
Author(s):  
Y. Hamouda ◽  
H. El Sayed ◽  
Th. Genaid
Keyword(s):  
Color Change ◽  
In Vitro Study ◽  
Vitro Study ◽  
Stain Removal ◽  
Restorative Materials

EFFECT OF HUMAN ENAMEL ON WEAR OF THREE TYPES OF INTERIM RESTORATIVE MATERIALS (AN IN-VITRO STUDY)

2017 ◽  
Vol 63 (4) ◽  
pp. 3933-3945
Author(s):  
Khaled Haggag ◽  
Muhammad Abbas ◽  
Zainab EL Sharkawy
Keyword(s):  
In Vitro Study ◽  
Vitro Study ◽  
Human Enamel ◽  
Restorative Materials

scholarly journals The behaviour of composites, glass ionomers and compomers in erosive conditions – in vitro study

2014 ◽  
Vol 60 (5) ◽  
pp. 200-203
Author(s):  
Andreea Borş ◽  
Cristina Molnar-Varlam ◽  
Melinda Székely
Keyword(s):  
Surface Roughness ◽  
Wear Resistance ◽  
Erosive Wear ◽  
In Vitro Study ◽  
Vitro Study ◽  
Initial Surface ◽  
Dental Filling ◽  
Filling Materials ◽  
Restorative Materials

Abstract Objective: The aim of this in vitro study was to evaluate the influence of erosive conditions on the wear resistance of aesthetic direct restorative materials. Methods: Six dental filling materials were tested: two composites (Filtek Z550 and X-tra fil), two compomers (Dyract Extra and Twinky Star) and two glass ionomers (Ketac Molar and Fuji II LC). Twenty disks (10mm×2mm) of each material were prepared (n=120) and kept in artificial saliva at 37˚C for 24 hours. Specimens were cycled in acidic soft drink (Coca-Cola) 5×/day, for 5’, over 30 days. Initial surface roughness ISR (Ra-μm) and final surface roughness FSR were measured using a profilometer. The wear rate was calculated as difference of final minus the initial roughness (ΔSR=FSR-ISR). For statistical analysis t-test and one-way ANOVA test were used by GraphPad Prism version 5.03 statistical software. The level of significance was set at p<0.05. Results: The erosive wear rates (mean±SD, μm) after exposure to acidic beverage were: 0.30±0.03 (Ketac Molar), 0.28±0.04 (Fuji II LC), 0.27±0.00 (Filtek Z550), 0.23±0.01 (X-tra fil), 0.20±0.00 (Twinky Star) and 0.14±0.01 Dyract Extra, respectively. There were significant differences between the tested materials (p<0.05). Conclusions: Dental filling materials had different behaviour under the same erosive condition, however all investigated aesthetic restorative materials showed surface degradation. These findings suggest that erosive wear resistance of tooth coloured restoratives could influence their longevity in intraoral acidic conditions. Acknowledgements: The study was supported by the Internal Research Grant no. 5/30.01.2013 of the University of Medicine and Pharmacy of Tirgu Mureş.

Effect of two fluoride varnishes on the color stability of three resin-based restorative materials: an in vitro study

2015 ◽  
Vol 7 (4) ◽  
pp. 355-360 ◽  
Author(s):  
Raha Tafaroji ◽  
Mina Biria ◽  
Farhad Ameri ◽  
Hassan Torabzadeh ◽  
Pasha Qahari ◽  
...  
Keyword(s):  
In Vitro Study ◽  
Color Stability ◽  
Vitro Study ◽  
Restorative Materials

scholarly journals Comparative Evaluation of Root Surface Changes by Air-Polishing using Glycine and Chlorhexidine Acetate Powder: An in-vitro Study

2017 ◽  
Vol 1 (1) ◽  
pp. 7-11
Author(s):  
Hardi Rajanbhai Shukla ◽  
Aditi Mathur ◽  
Neema Shetty ◽  
Barkha Makhijani ◽  
Balaji Manohar
Keyword(s):  
In Vitro Study ◽  
Root Surface ◽  
Periodontal Therapy ◽  
Vitro Study ◽  
Tooth Surface ◽  
Air Polishing ◽  
Biofilm Removal ◽  
Stain Removal ◽  
Surface Changes

Background: Biofilm removal is the central part of the etiotropic and maintenance phase of periodontal therapy. Commercially available injection water jets such as Prophy-Jet allows an efficient and convenient biofilm removal as an adjunct to mechanical periodontal therapy. But, due to the abrasive nature of traditionally used air polishing powders such as sodium bicarbonate, there is a continuous research going on for less abrasive materials. Aims: To compare the effectiveness of air polishing using glycine powder and chlorhexidine acetate powder on tooth surface as compared to ultrasonic scaling and also to evaluate the time taken for stain removal. Materials and Methods: Thirty fully erupted, single rooted teeth extracted due to poor periodontal prognosis were used in this in-vitro study. The sample teeth were divided into 3 equal groups and stained in coffee solution. The test Groups A and B underwent air-polishing with glycine powder and chlorhexidine acetate powder respectively. Group C was control group and underwent ultrasonic scaling. Time taken for stain removal was recorded. The sample teeth were also evaluated under a stereo-microscope and digital micrometer preprocedurally and post-procedurally to measure surface changes. Results: The study showed statistically significant results (p<0.05) when measurements of changes in surface roughness of samples treated with glycine powder air-polishing were compared with ultrasonic scaling and chlorhexidine acetate powder air-polishing were compared with ultrasonic scaling. Surface texture loss as well as time taken for stain removal was minimum with glycine powder and maximum with ultrasonic scaling. Conclusion: Air-polishing with glycine powder was least abrasive on root surface followed by chlorhexidine acetate powder air-polishing. This is because of the lower particle size of glycine which also covers larger area in lesser time.  

Sign in / Sign up

Export Citation Format

Share Document