Effects of Strain Rate on the Strain Induced Martensite Nucleation and Growth in 301LN Metastable Austenitic Steel

2021 ◽  
Author(s):  
Lalit Pun ◽  
Guilherme Corrêa Soares ◽  
Matti Isakov ◽  
Mikko Hokka
Keyword(s):  
Strain Rate ◽  
Austenitic Steel ◽  
Nucleation And Growth ◽  
Metastable Austenitic Steel ◽  
Strain Induced Martensite

Spherulite Structures in a Melt Spun Fe-Ni Austenitic Steel

1985 ◽  
Vol 43 ◽  
pp. 52-53
Author(s):  
G. M. Michal ◽  
T. K. Glasgow ◽  
T. J. Moore
Keyword(s):  
Austenitic Steel ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Large Range ◽  
Amorphous Structure ◽  
Nucleation And Growth ◽  
Ni Alloys ◽  
Melt Spun ◽  
Crystal Fibers ◽  
Rapidly Solidified

Large additions of B to Fe-Ni alloys can lead to the formation of an amorphous structure, if the alloy is rapidly cooled from the liquid state to room temperature. Isothermal aging of such structures at elevated temperatures causes crystallization to occur. Commonly such crystallization pro ceeds by the nucleation and growth of spherulites which are spherical crystalline bodies of radiating crystal fibers. Spherulite features were found in the present study in a rapidly solidified alloy that was fully crysstalline as-cast. This alloy was part of a program to develop an austenitic steel for elevated temperature applications by strengthening it with TiB2. The alloy contained a relatively large percentage of B, not to induce an amorphous structure, but only as a consequence of trying to obtain a large volume fracture of TiB2 in the completely processed alloy. The observation of spherulitic features in this alloy is described herein. Utilization of the large range of useful magnifications obtainable in a modern TEM, when a suitably thinned foil is available, was a key element in this analysis.

scholarly journals Structural Transformations and Mechanical Properties of Metastable Austenitic Steel under High Temperature Thermomechanical Treatment

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 645
Author(s):  
Igor Litovchenko ◽  
Sergey Akkuzin ◽  
Nadezhda Polekhina ◽  
Kseniya Almaeva ◽  
Evgeny Moskvichev
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
High Temperature ◽  
Austenitic Steel ◽  
Structural Transformations ◽  
Initial State ◽  
Twin Boundaries ◽  
Metastable Austenitic Steel ◽  
Average Grain Size ◽  
Heating Up

The effect of high-temperature thermomechanical treatment on the structural transformations and mechanical properties of metastable austenitic steel of the AISI 321 type is investigated. The features of the grain and defect microstructure of steel were studied by scanning electron microscopy with electron back-scatter diffraction (SEM EBSD) and transmission electron microscopy (TEM). It is shown that in the initial state after solution treatment the average grain size is 18 μm. A high (≈50%) fraction of twin boundaries (annealing twins) was found. In the course of hot (with heating up to 1100 °C) plastic deformation by rolling to moderate strain (e = 1.6, where e is true strain) the grain structure undergoes fragmentation, which gives rise to grain refining (the average grain size is 8 μm). Partial recovery and recrystallization also occur. The fraction of low-angle misorientation boundaries increases up to ≈46%, and that of twin boundaries decreases to ≈25%, compared to the initial state. The yield strength after this treatment reaches up to 477 MPa with elongation-to-failure of 26%. The combination of plastic deformation with heating up to 1100 °C (e = 0.8) and subsequent deformation with heating up to 600 °C (e = 0.7) reduces the average grain size to 1.4 μm and forms submicrocrystalline fragments. The fraction of low-angle misorientation boundaries is ≈60%, and that of twin boundaries is ≈3%. The structural states formed after this treatment provide an increase in the strength properties of steel (yield strength reaches up to 677 MPa) with ductility values of 12%. The mechanisms of plastic deformation and strengthening of metastable austenitic steel under the above high-temperature thermomechanical treatments are discussed.

Acoustic emission measurements on metastable austenitic steel oligocrystals

2021 ◽  
Vol 827 ◽  
pp. 142066
Author(s):  
R. Lehnert ◽  
A. Franke ◽  
H. Biermann ◽  
A. Weidner
Keyword(s):  
Acoustic Emission ◽  
Austenitic Steel ◽  
Metastable Austenitic Steel

Critical grain size to limit the hydrogen-induced ductility drop in a metastable austenitic steel

2015 ◽  
Vol 40 (33) ◽  
pp. 10697-10703 ◽  
Author(s):  
Arnaud Macadre ◽  
Nobuo Nakada ◽  
Toshihiro Tsuchiyama ◽  
Setsuo Takaki
Keyword(s):  
Grain Size ◽  
Austenitic Steel ◽  
Metastable Austenitic Steel ◽  
Critical Grain Size
Sign in / Sign up

Export Citation Format

Share Document