Low-Cycle Fatigue Life and Plasticity Mechanisms of a Fe−15Mn−10Cr−8Ni−4Si Seismic Damping Alloy Under Cyclic Loading at Various Temperatures

2020 ◽  
Author(s):  
Takahiro Sawaguchi ◽  
Ilya Nikulin ◽  
Kazuyuki Ogawa ◽  
Susumu Takamori ◽  
Fumiyoshi Yoshinaka ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Cyclic Loading ◽  
Low Cycle Fatigue ◽  
Cycle Fatigue ◽  
Seismic Damping

Low-cycle fatigue life and plasticity mechanisms of a Fe−15Mn−10Cr−8Ni−4Si seismic damping alloy under cyclic loading at various temperatures

2021 ◽  
Vol 220 ◽  
pp. 117267
Author(s):  
Takahiro Sawaguchi ◽  
Ilya Nikulin ◽  
Kazuyuki Ogawa ◽  
Susumu Takamori ◽  
Fumiyoshi Yoshinaka ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Cyclic Loading ◽  
Low Cycle Fatigue ◽  
Cycle Fatigue ◽  
Seismic Damping

Low Cycle Fatigue Life Prediction of Ti-6Al-4V Titanium Alloy under Multi-Axial Non Proportional Cyclic Loading

2013 ◽  
Vol 668 ◽  
pp. 814-817
Author(s):  
Rui Feng Wang ◽  
You Tang Li ◽  
Hu Ping An
Keyword(s):  
Fatigue Life ◽  
Cyclic Loading ◽  
Low Cycle Fatigue ◽  
Testing Machine ◽  
Equivalent Strain ◽  
Cycle Fatigue ◽  
Critical Plane ◽  
Plane Method ◽  
Torsional Strain ◽  
Method Model

A series multi-axial tension and torsion low cycle fatigue life experiments of Ti-6Al-4V alloy were conducted on the MTS tension and torsion joint testing machine, in which the torsional strain control and non proportional cyclic loading method under the loading paths of circular, rectangular, square, oval and diamond were successively used. The experimental results are compared and analyzed with the results that calculated by the equivalent strain model, the energy method model and the critical plane method model. The results show that the critical plane method is the accurate prediction model to predict the multi-axial low cycle fatigue life of Ti-6Al-4V alloy.

On low cycle fatigue life of nickel-based superalloy valve membranes under non-proportional cyclic loading

2008 ◽  
Vol 30 (7) ◽  
pp. 1160-1168 ◽  
Author(s):  
M ABBADI ◽  
S BELOUETTAR ◽  
P MUZZO ◽  
P KREMER ◽  
O OUSSOUADDI ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Cyclic Loading ◽  
Low Cycle Fatigue ◽  
Cycle Fatigue ◽  
Nickel Based Superalloy

Low-Cycle Fatigue Performance of Buckling Restrained Braces and Assessment of Cumulative Damage under Severe Earthquakes

2018 ◽  
Vol 763 ◽  
pp. 867-874
Author(s):  
Yu Shu Liu ◽  
Ke Peng Chen ◽  
Guo Qiang Li ◽  
Fei Fei Sun
Keyword(s):  
Fatigue Life ◽  
Energy Dissipation ◽  
Structural Reliability ◽  
Low Cycle Fatigue ◽  
Engineering Application ◽  
Fatigue Performance ◽  
Cycle Fatigue ◽  
Variable Amplitude ◽  
Buckling Restrained Braces ◽  
Energy Dissipation Devices

Buckling Restrained Braces (BRBs) are effective energy dissipation devices. The key advantages of BRB are its comparable tensile and compressive behavior and stable energy dissipation capacity. In this paper, low-cycle fatigue performance of domestic BRBs is obtained based on collected experimental data under constant and variable amplitude loadings. The results show that the relationship between fatigue life and strain amplitude satisfies the Mason-Coffin equation. By adopting theory of structural reliability, this paper presents several allowable fatigue life curves with different confidential levels. Besides, Palmgren-Miner method was used for calculating BRB cumulative damages. An allowable damage factor with 95% confidential level is put forward for assessing damage under variable amplitude fatigue. In addition, this paper presents an empirical criterion with rain flow algorithm, which may be used to predict the fracture of BRBs under severe earthquakes and provide theory and method for their engineering application. Finally, the conclusions of the paper were vilified through precise yet conservative prediction of the fatigue failure of BRB.

scholarly journals Fatigue Testing of Wearable Sensing Technologies: Issues and Opportunities

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4070
Author(s):  
Andrea Karen Persons ◽  
John E. Ball ◽  
Charles Freeman ◽  
David M. Macias ◽  
Chartrisa LaShan Simpson ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Prediction Models ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
Wearable Sensors ◽  
Fatigue Tests ◽  
Proof Of Concept ◽  
Cycle Fatigue ◽  
Wearable Sensing ◽  
Failure Data

Standards for the fatigue testing of wearable sensing technologies are lacking. The majority of published fatigue tests for wearable sensors are performed on proof-of-concept stretch sensors fabricated from a variety of materials. Due to their flexibility and stretchability, polymers are often used in the fabrication of wearable sensors. Other materials, including textiles, carbon nanotubes, graphene, and conductive metals or inks, may be used in conjunction with polymers to fabricate wearable sensors. Depending on the combination of the materials used, the fatigue behaviors of wearable sensors can vary. Additionally, fatigue testing methodologies for the sensors also vary, with most tests focusing only on the low-cycle fatigue (LCF) regime, and few sensors are cycled until failure or runout are achieved. Fatigue life predictions of wearable sensors are also lacking. These issues make direct comparisons of wearable sensors difficult. To facilitate direct comparisons of wearable sensors and to move proof-of-concept sensors from “bench to bedside,” fatigue testing standards should be established. Further, both high-cycle fatigue (HCF) and failure data are needed to determine the appropriateness in the use, modification, development, and validation of fatigue life prediction models and to further the understanding of how cracks initiate and propagate in wearable sensing technologies.

Uniaxial Ratcheting and Low-Cycle Fatigue Failure of U75V Rail Steel

2016 ◽  
Vol 853 ◽  
pp. 246-250 ◽  
Author(s):  
Tao Fang ◽  
Qian Hua Kan ◽  
Guo Zheng Kang ◽  
Wen Yi Yan
Keyword(s):  
Fatigue Life ◽  
Strain Amplitude ◽  
Stress Ratio ◽  
Stress Amplitude ◽  
Rail Steel ◽  
Low Cycle Fatigue ◽  
Mean Stress ◽  
Cycle Fatigue ◽  
Ratcheting Strain ◽  
Cyclic Straining

Experiments on U75V rail steel were carried out to investigate the cyclic feature, ratcheting behavior and low-cycle fatigue under both strain- and stress-controlled loadings at room temperature. It was found that U75V rail steel shows strain amplitude dependent cyclic softening feature, i.e., the responded stress amplitude under strain-controlled decreases with the increasing number of cycles and reaches a stable value after about 20th cycle. Ratcheting strain increases with an increasing stress amplitude and mean stress, except for stress ratio, and the ratcheting strain in failure also increases with an increasing stress amplitude, mean stress and stress ratio. The low-cycle fatigue lives under cyclic straining decrease linearly with an increasing strain amplitude, the fatigue lives under cyclic stressing decrease with an increasing mean stress except for zero mean stress, and decrease with an increasing stress amplitude. Ratcheting behavior with a high mean stress reduces fatigue life of rail steel by comparing fatigue lives under stress cycling with those under strain cycling. Research findings are helpful to evaluate fatigue life of U75V rail steel in the railways with passenger and freight traffic.

A Multi-Level Low Cycle Fatigue Damage Model for Forging Die Material

2006 ◽  
Vol 514-516 ◽  
pp. 804-809
Author(s):  
S. Gao ◽  
Ewald Werner
Keyword(s):  
Fatigue Life ◽  
Fatigue Damage ◽  
Low Cycle Fatigue ◽  
Damage Model ◽  
Fatigue Loading ◽  
Cycle Fatigue ◽  
Die Material ◽  
Multi Level ◽  
Loading Sequence ◽  
Forging Die

The forging die material, a high strength steel designated W513 is considered in this paper. A fatigue damage model, based on thermodynamics and continuum damage mechanics, is constructed in which both the previous damage and the loading sequence are considered. The unknown material parameters in the model are identified from low cycle fatigue tests. Damage evolution under multi-level fatigue loading is investigated. The results show that the fatigue life is closely related to the loading sequence. The fatigue life of the materials with low fatigue loading first followed by high fatigue loading is longer than that for the reversed loading sequence.

Sign in / Sign up

Export Citation Format

Share Document