A Study on Effect of Seal Profile on Leakage Flow Rate in a Labyrinth Seal Using Computation Fluid Dynamics Analysis

2018 ◽  
Author(s):  
J Sharana Basavaraja ◽  
Aprameya C R ◽  
Rajesh P
Keyword(s):  
Fluid Dynamics ◽  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Dynamics Analysis ◽  
Computation Fluid Dynamics ◽  
Leakage Flow Rate

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

scholarly journals Leakage Characteristic Identification of Labyrinth Seals on Reciprocating Piston through Transient Simulations

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Lingzi Wang ◽  
Jianmei Feng ◽  
Mingfeng Wang ◽  
Zenghui Ma ◽  
Xueyuan Peng
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Piston Compressor ◽  
Pressure Change ◽  
Labyrinth Seal ◽  
Relative Molecular Mass ◽  
Geometrical Parameters ◽  
Leakage Flow ◽  
Reciprocating Motion ◽  
Leakage Flow Rate

In the reciprocating labyrinth piston compressor, the characteristic of the internal leakage is crucial for the leakage management and performance improvement of the compressor. However, most of the published studies investigated the rotor-stator system, and those who study the reciprocating piston-cylinder system basically focus on the effects of the geometrical parameters. These conclusions could not directly be applied to predict the real-time leakage flow rate through the labyrinth seal because of the fast reciprocating motion of the piston, which will cause continually pressure change in two compression chambers, and then the pressure fluctuation will affect the flow through the labyrinth seal. A transient simulation model employing the multiscale dynamic mesh, which considers the effect of the reciprocating motion of the piston in the cylinder, is established to identify the characteristics of the internal leakage. This model was verified by a specially designed compressor, and the influence of various parameters was analyzed in detail. The sealing performance decreased linearly with the increase in the pressure ratio, and higher pressure inlet leads to higher leakage flow under the same pressure ratio. The labyrinth seal performance positively correlated to the increase of the rotational speed. Leakage characteristics of five working mediums were carried out, and the results indicated that the relative leakage decreased with an increase in the relative molecular mass. From this study, the realistic internal leakage flow rate under different operating parameters in the reciprocating labyrinth piston compressor could be predicated.

Numerical Investigations on the Leakage and Rotordynamic Characteristics of Pocket Damper Seals—Part II: Effects of Partition Wall Type, Partition Wall Number, and Cavity Depth

2014 ◽  
Vol 137 (3) ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Cavity Depth ◽  
Partition Wall ◽  
Leakage Flow Rate ◽  
Direct Stiffness ◽  
Cfd Method ◽  
Positive Direct ◽  
Orbit Model

Effects of partition wall type, partition wall number and cavity depth on the leakage and rotordynamic characteristics of the pocket damper seal (PDS) were numerically investigated using a presented 3D transient computational fluid dynamics (CFD) method based on the multifrequency elliptical whirling orbit model. The accuracy and availability of this transient CFD method and the multifrequency elliptical whirling orbit model were demonstrated with the experimental data of the experimental eight-bladed fully partitioned pocket damper seal (FPDS). The leakage flow rates and frequency-dependent rotordynamic coefficients of PDS were computed for two types of partition wall (namely conventional PDS and fully partitioned PDS), four partition wall numbers including the labyrinth seal (no partition wall) and six cavity depths including the plain smooth seal (zero cavity depth) at operational conditions with or without inlet preswirl and 15,000 rpm rotational speed. The numerical results show that the FPDS has the similar leakage performance and more superior stability capacity than the conventional PDS. The FPDS possesses slightly larger leakage flow rate (∼2.6–4.0% larger) compared to the labyrinth seal. Eight is a preferable value for the partition wall number to gain the best leakage performance of the FPDS with the least manufacturing cost. The FPDS possesses significantly larger stiffness and damping than the labyrinth seal. Increasing partition wall number results in a significant increase in the direct stiffness but limited desirable effect on the effective damping. The FPDS possesses the lowest leakage flow rate when the cavity depth is about 2.0 mm. Compared to the plain smooth seal, the FPDS possesses larger positive direct stiffness and significantly less direct damping and effective damping. Increasing cavity depth results in a significant decrease in the stabilizing direct damping and the magnitude of the destabilizing cross-coupling stiffness. H= 3.175 mm is a preferable value of the cavity depth for which the effective damping of the FPDS is largest, especially for the concerned frequencies (80–120 Hz) where most multistage high-pressure centrifugal compressors have stability problem.

scholarly journals Optimizing the Geometric Parameters of a Straight-Through Labyrinth Seal to Minimize the Leakage Flow Rate and the Discharge Coefficient

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 705
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Flow Rate ◽  
Axial Length ◽  
Discharge Coefficient ◽  
Labyrinth Seal ◽  
Geometric Parameters ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Tooth Width ◽  
Cavity Width

A straight-through labyrinth seal is one of the most popular non-contacting annular seals through which energy dissipation by turbulence viscosity interaction is achieved with a series of teeth and cavities. The geometric parameters of the straight-through labyrinth seal, such as clearance, tooth width, tooth height, cavity width, and tooth inclination angle, affect its performance. The space for installing a labyrinth seal in turbomachinery is limited, and so it is important to optimize its geometry for a fixed axial length in order to minimize the leakage flow rate and the discharge coefficient. The objective of the current study is to understand the effects of changing the geometric parameters of the seal on the leakage flow rate and the discharge coefficient, and to determine the optimized geometry for a fixed axial length. When the whole axial length is fixed, the most effective way to decrease the discharge coefficient is to reduce the cavity width by increasing the number of cavities. However, if the number of cavities is too high, the beneficial effect of more cavities can be reversed. The results of this study will help turbomachinery manufacturers to design a more efficient labyrinth seal. Numerical simulations of leakage flow for the straight-through labyrinth seal were carried out using Reynolds-Averaged Navier–Stokes (RANS) models, and the results for their discharge coefficients and pressure distributions were compared to previously published experimental data.

Performance Analysis of a Rotating Labyrinth Seal With Radial Growth

2013 ◽  
Author(s):  
Sivakumar Subramanian ◽  
A. S. Sekhar ◽  
B. V. S. S. S. Prasad
Keyword(s):  
Flow Rate ◽  
Radial Growth ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Wide Range ◽  
Structural Deformations ◽  
Angular Velocities ◽  
Computational Methodology ◽  
Initial Clearance

A computational methodology is proposed to predict the running clearance of a six-tooth straight-through rotating labyrinth seal numerically by taking into account both the centrifugal and thermal growths. Four different angular velocities ranging from 0 to 3000 rad/s are chosen to study the influence of rotation on the leakage flow rate. The detailed leakage flow fields and the structural deformations are presented. Further, different pressure ratios in the range of 1.1 to 2.5 have been investigated for a wide range of initial clearances. The methodology is validated against the available data in the literature. It is found out that there is a significant reduction in leakage flow rate by incorporating the radial growth for a particular operating condition. However, for a given initial clearance, the rotation has negligible effect on the reduction in the leakage flow rate, except at pressure ratios lower than 1.7. Further; the rotation has more prominent effect for smaller clearance values.

Effects of Pressure Ratio and Fin Pitch on Leakage Flow Characteristics in High Rotating Labyrinth Seals

2006 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Geometrical Structure ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Rotational Axis ◽  
Labyrinth Seals ◽  
Sealing Performance ◽  
Leakage Flow Rate

Labyrinth seals represent an important flow element in the sealing equipment of modern turbomachinery industries. The straight-through and stepped labyrinth seal are widely used in modern steam turbine due to their comparable simple structure and low manufactured costs. The influence of pressure ratio and fin pitch on the leakage flow characteristics of the straight-through and stepped labyrinth seals is numerically determined. The pressure ratio is defined as the outlet static pressure divided by the inlet total pressure. The fin pitch varied in the fixed axial distance of the labyrinth seal. The geometries investigated represent designs of the straight-through and stepped labyrinth seal typical for modern steam turbines. The leakage flow fields in the high rotating straight-through and stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT with the fixed seal clearance and fins geometrical structure. The effect of the rotational axis is also taken into account in numerical computations. Numerical simulations covered a range of pressure ratio and fin pitch for the straight-through and stepped labyrinth seals. Dimensionless discharge coefficients, describing the sealing performance, are calculated from the simulation results. The numerical results show that pressure ratio and fin pitch both affects the sealing performance with the fixed seal clearance and fin geometrical structure. The leakage flow rate decreases with the decreasing fin pitch for both the straight-through and stepped labyrinth seal at the fixed pressure ratio. Furthermore, the leakage flow rate decreases with the increasing pressure ratio at the fixed fin pitch for two kinds of labyrinth seals in the present study. This research provides technical support for improved design of labyrinth seals in turbomachinery.

Numerical Investigations on the Leakage and Rotordynamic Characteristics of Pocket Damper Seals: Part II — Effects of Partition Wall Type, Partition Wall Number and Cavity Depth

2014 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Cavity Depth ◽  
Partition Wall ◽  
Leakage Flow Rate ◽  
Direct Stiffness ◽  
Cfd Method ◽  
Positive Direct ◽  
Orbit Model

Effects of partition wall type, partition wall number and cavity depth on the leakage and rotordynamic characteristics of the pocket damper seal (PDS) were numerically investigated using a presented 3D transient CFD method based on the multi-frequency elliptical whirling orbit model. The accuracy and availability of this transient CFD method and the multi-frequency elliptical whirling orbit model were demonstrated with the experimental data of the experimental eight-bladed fully-partitioned pocket damper seal (FPDS). The leakage flow rates and frequency-dependent rotordynamic coefficients of PDS were computed for two types of partition wall (namely conventional PDS and fully-partitioned PDS), four partition wall numbers including the labyrinth seal (no partition wall) and six cavity depths including the plain smooth seal (zero cavity depth) at operational conditions with or without inlet preswirl and 15000rpm rotational speed. The numerical results show that the FPDS has the similar leakage performance and more superior stability capacity than the conventional PDS. The FPDS possesses slightly larger leakage flow rate (∼2.6–4.0% larger) compared to the labyrinth seal. Eight is a preferable value for the partition wall number to gain the best leakage performance of the FPDS with the least manufacturing cost. The FPDS possesses significantly larger stiffness and damping than the labyrinth seal. Increasing partition wall number results in a significant increase in the direct stiffness but limited desirable effect on the effective damping. The FPDS possesses the lowest leakage flow rate when the cavity depth is about 2.0mm. Compared to the plain smooth seal, the FPDS possesses larger positive direct stiffness and significantly less direct damping and effective damping. Increasing cavity depth results in a significant decrease in the stabilizing direct damping and the magnitude of the destabilizing cross-coupling stiffness. H = 3.175mm is a preferable value of the cavity depth for which the effective damping of the FPDS is largest, especially for the concerned frequencies (80–120Hz) where most multistage high-pressure centrifugal compressors have stability problem.

Leakage Flow and Heat Transfer Over Shrouded Turbine Blades

2000 ◽  
Author(s):  
Yumin Xiao ◽  
R. S. Amano
Keyword(s):  
Flow Rate ◽  
High Efficiency ◽  
Stokes Equations ◽  
Turbine Blades ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Complex Flow ◽  
Flow Area ◽  
Sharp Drop ◽  
Leakage Flow Rate

Abstract In this paper a high efficiency labyrinth seal and the staggered labyrinth seal for shrouded blades was presented. The flows in the seal with single, double, and triple tip seals were simulated by solving the two-dimensional Reynolds-averaged Navier-Stokes equations (RANS) and a compressible k-ε turbulence model. A multi-zone technique was used to generate the grids in the complex flow channel. The calculation results showed that the presently proposed staggered labyrinth seal is more efficient than the typical one and the leakage flow rate is dominated by the minimum flow area and the pressure difference. Comparing the performance with the typical labyrinth seal, the present staggered labyrinth seal model can average the total pressure drop among the seals, while the typical one induces a sharp drop across the first tooth. It showed that the leakage flow rate varies as a function of the number of seals to the power of −0.45. For the cases of multiple-seals the space between two seals has little effect on the total mass flow rate. Finally, decreasing the wall temperature will result in an increase of leakage flow.

Application of blade tip shroud brush seal to improve the aerodynamic performance of turbine stage

2019 ◽  
Vol 234 (6) ◽  
pp. 777-794
Author(s):  
Dengqian Ma ◽  
Jun Li ◽  
Yuanqiao Zhang ◽  
Zhigang Li ◽  
Xin Yan ◽  
...  
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Aerodynamic Performance ◽  
Leakage Flow ◽  
Turbine Stage ◽  
Brush Seal ◽  
Leakage Flow Rate ◽  
Blade Tip ◽  
Brush Seals ◽  
Tip Shroud

The blade tip shroud brush seal is applied to replace the labyrinth seal for the aerodynamic performance improvement of turbine stage. The leakage flow characteristics of the brush seal are numerically predicted by using the Reynolds-Averaged Navier–Stokes equations and non-linear Darcian porous medium model. The numerical leakage flow rate of the brush seal is in well agreement with the experimental data. The last and first long teeth of the labyrinth seal were designed to bristle pack named as the postposed and preposed brush seals based on the 1.5 turbine stage. The leakage flow rate and aerodynamic performance of the turbine stage with blade tip shroud labyrinth seal and brush seal are numerically investigated. The effect of the sealing clearance between bristle pack and tip shroud on the aerodynamic performance of turbine stage is conducted which ranged from 0 mm to 0.4 mm. The axial deflection of the bristle pack is analyzed with consideration of the aerodynamic forces and contact frictional force. The obtained results show that the leakage flow rate of the tip shroud brush seals with bristle tip 0.4 mm clearance which decreases by up to 18% in comparison with the labyrinth seal, and the aerodynamic efficiency increases by 0.6%. Compared to the tip labyrinth seal, tip shroud brush seals can decrease the relative deflection angle of exit flow. This flow behavior results in reducing the mixing loss between the tip leakage flow and mainstream. The similar axial deflection of the bristle pack for two kinds of brush seals is observed at the same sealing clearance. The deflection of the bristle pack under the function of the aerodynamic forces is protected by the backing plate. This work provides the theoretical basis and technical support for the brush seal application in the turbine industries.

Numerical Investigations on the Leakage Flow Characteristics of Pocket Damper Seals

2011 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng ◽  
Jiandao Yang ◽  
Rui Yang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Rotational Speed ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Numerical Results ◽  
Flow Coefficient ◽  
Leakage Flow ◽  
Leakage Flow Rate

The effects of pressure ratios, rotational speeds and sealing clearances on the leakage flow characteristics of pocket damper seals (PDS) were numerically investigated using Reynolds-Averaged Navier-Stokes (RANS) solutions. The leakage flow rate of the experimental PDS with the eight-bladed and eight-pocket was conducted at three different pressure drops and three different rotational speeds. The numerical results were in agreement with the experimental data. Six pressure ratios, four rotational speeds and four sealing clearances were utilized to study the effects of theses factors on the leakage flow characteristics of the PDS. Numerical results show that the leakage rate of the PDS increases with decreased pressure ratio. The leakage rate decreases with the increasing rotational speed, and this phenomenon is more pronounced at higher rotational speed. At the highest rotational speed 20200rpm, the flow coefficient is up to 4.4% less than that of the non-rotating case. The leakage rate increases linearly with sealing clearance increasing. The comparison of the leakage flow rate shows that the PDS leaks slightly less than that of the labyrinth seal at the same pressure ratio, rotational speed and sealing clearance, especially at the higher rotational speed case. Furthermore, the circumferential partition wall can significantly decrease the circumferential flow in the PDS cavity. At the highest rotational speed with 20200rpm, the swirl ratio in the active and inactive cavity of the PDS is reduced by 94.5% and 46% compared to the labyrinth seal, respectively.

Sign in / Sign up

Export Citation Format

Share Document