Innovation as Response to Emissions Legislation: Revisiting the Automatic Catalytic Converter at Johnson Matthey

2009 ◽  
Author(s):  
Lan Tao ◽  
Elizabeth W. Garnsey ◽  
David Probert ◽  
Tom Ridgman
Keyword(s):  
Catalytic Converter

Microstructure and reactivity of small metal particles: The role of Ce additives

1992 ◽  
Vol 50 (1) ◽  
pp. 318-319
Author(s):  
L.D. Schmidt ◽  
K. R. Krause ◽  
J. M. Schwartz ◽  
X. Chu
Keyword(s):  
Atmospheric Pressure ◽  
Noble Metals ◽  
Mixed Oxides ◽  
Catalytic Properties ◽  
Chemical Shifts ◽  
Catalytic Converter ◽  
Structural Evolution ◽  
Single Particles ◽  
Small Metal Particles

The evolution of microstructures of 10- to 100-Å diameter particles of Rh and Pt on SiO2 and Al2O3 following treatment in reducing, oxidizing, and reacting conditions have been characterized by TEM. We are able to transfer particles repeatedly between microscope and a reactor furnace so that the structural evolution of single particles can be examined following treatments in gases at atmospheric pressure. We are especially interested in the role of Ce additives on noble metals such as Pt and Rh. These systems are crucial in the automotive catalytic converter, and rare earths can significantly modify catalytic properties in many reactions. In particular, we are concerned with the oxidation state of Ce and its role in formation of mixed oxides with metals or with the support. For this we employ EELS in TEM, a technique uniquely suited to detect chemical shifts with ∼30Å resolution.

High Resolution Transmission Electron Microscopy of an automobile catalytic converter

1990 ◽  
Vol 48 (4) ◽  
pp. 242-243
Author(s):  
Jan-Olle Malm ◽  
Jan-Olov Bovin
Keyword(s):  
Electron Microscopy ◽  
High Resolution ◽  
Catalytic Converter ◽  
Active Material ◽  
Image Intensifier ◽  
High Resolution Electron Microscopy ◽  
Detailed Knowledge ◽  
Transmission Electron ◽  
Resolution Electron ◽  
Atomic Surface

Understanding of catalytic processes requires detailed knowledge of the catalyst. As heterogeneous catalysis is a surface phenomena the understanding of the atomic surface structure of both the active material and the support material is of utmost importance. This work is a high resolution electron microscopy (HREM) study of different phases found in a used automobile catalytic converter.The high resolution micrographs were obtained with a JEM-4000EX working with a structural resolution better than 0.17 nm and equipped with a Gatan 622 TV-camera with an image intensifier. Some work (e.g. EDS-analysis and diffraction) was done with a JEM-2000FX equipped with a Link AN10000 EDX spectrometer. The catalytic converter in this study has been used under normal driving conditions for several years and has also been poisoned by using leaded fuel. To prepare the sample, parts of the monolith were crushed, dispersed in methanol and a drop of the dispersion was placed on the holey carbon grid.

EMISSION OF POLYCYCLIC AROMATIC HYDROCARBONS CONTAINED IN COMBUSTION PRODUCTS OF GASOLINE ENGINES

2018 ◽  
Vol 62 (3) ◽  
pp. 341-346 ◽  
Author(s):  
M. Assad ◽  
V. V. Grushevski ◽  
O. G. Penyazkov ◽  
I. N. Tarasenko
Keyword(s):  
Polycyclic Aromatic Hydrocarbons ◽  
Aromatic Hydrocarbons ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Catalytic Converter ◽  
Combustion Products ◽  
Chromatography Method ◽  
Exhaust Gases ◽  
Polycyclic Aromatic ◽  
Load Mode

The concentration of 16 polycyclic aromatic hydrocarbons (PAHs) in the gasoline combustion products emitted into the atmosphere by internal combustion engines (ICE) has been measured using the gas chromatography method. The concentrations of PAHs in the exhaust gases sampled behind a catalytic converter has been determined when the ICE operates in five modes: idle mode, high speed mode, load mode, ICE cold start mode (engine warm-up) and transient mode. Using 92 RON, 95 RON and 98 RON gasoline the effect of the octane number of gasoline on the PAHs content in the exhaust gases has been revealed. The concentration of the most carcinogenic component (benzo(α)pyrene) in the exhaust gases behind a catalytic converter significantly exceeds a reference value of benzo(α)pyrene in the atmospheric air established by the WHO and the EU for ICE in the load mode.

An Investigation on the Performance of an Oxidation Catalyst Using Two-dimensional Simulation with Detailed Reaction Mechanism

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Sreeharsh Nair ◽  
Mayank Mittal
Keyword(s):  
Single Channel ◽  
Catalytic Converter ◽  
Oxidation Catalyst ◽  
Low Temperature Combustion ◽  
Wide Range ◽  
Detailed Reaction Mechanism ◽  
Temperature Combustion ◽  
High Concentrations ◽  
Dimensional Simulation ◽  
Surface Reaction Kinetics

AbstractThe advent of stricter emission standards has increased the importance of aftertreatment devices and the role of numerical simulations in the evolution of better catalytic converters in order to satisfy these emission regulations. In this paper, a 2-D numerical simulation of a single channel of the monolith catalytic converter is presented by using detailed surface reaction kinetics aiming to investigate the chemical behaviour inside the converter. The model has been developed to study the conversion of carbon monoxide (CO) in the presence of propene (C3H6) for low-temperature combustion (LTC) engine application. The inhibition effect of C3H6 over a wide range of CO inlet concentrations is investigated. Considering both low and high levels of CO concentration at the inlet, the 2-D model predicted better results than their corresponding 1-D counterparts when compared with the experimental data from literature. It was also observed that C3H6 inhibition at high temperatures was significant, particularly for high concentrations of CO compared to low concentrations of CO at the inlet.

scholarly journals Small Cogeneration Unit with Heat and Electricity Storage

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2102
Author(s):  
Josef Stetina ◽  
Michael Bohm ◽  
Michal Brezina
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Storage System ◽  
Internal Combustion ◽  
Energy Storage System ◽  
Balance Model ◽  
Exhaust Pipe ◽  
Water Storage Tank

A micro cogeneration unit based on a three-cylinder internal combustion engine, Skoda MPI 1.0 L compressed natural gas (CNG), with an output of 25 kW at 3000 RPM is proposed in this paper. It is a relatively simple engine, which is already adopted by the manufacturer to operate on CNG. The engine life and design correspond to the original purpose of use in the vehicle. A detailed dynamic model was created in the GT-SUITE environment and implemented into an energy balance model that includes its internal combustion engine, heat exchangers, generator, battery storage, and water storage tank. The 1D internal combustion engine model provides us with information on engine start-up time, actual effective power, friction power, and the amount of heat going to the cooling system and exhaust pipe. The catalytic converter was removed from the exhaust pipe, and the engine was always operating at full load; thus, engine power control is not considered. An energy storage system for an island operation of the entire power unit for a large, detached house was designed to withstand accumulated energy for a few days in the case of a breakout. To reach a low initial system cost, the possible implementation of worn-out battery packs toward emission reduction in terms of the second life of the battery is proposed. The energy and emission balance are carried out, and the service life of the engine is also discussed.

scholarly journals Recovery of Platinum from a Spent Automotive Catalyst through Chloride Leaching and Solvent Extraction

Recycling ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 27
Author(s):  
Ana Méndez ◽  
Carlos A. Nogueira ◽  
Ana Paula Paiva
Keyword(s):  
Solvent Extraction ◽  
Environmental Sustainability ◽  
Catalytic Converter ◽  
Reaction Times ◽  
Model Solution ◽  
Critical Metals ◽  
Experimental Conditions ◽  
Chloride Leaching ◽  
Good Potential ◽  
Hydrometallurgical Treatment

Considering economics and environmental sustainability, recycling of critical metals from end-of-life devices should be a priority. In this work the hydrometallurgical treatment of a spent automotive catalytic converter (SACC) using HCl with CaCl2 as a leaching medium, and solvent extraction (SX) with a thiodiglycolamide derivative, is reported. The aim was to develop a leaching scheme allowing high Pt recoveries and minimizing Al dissolution, facilitating the application of SX. The replacement of part of HCl by CaCl2 in the leaching step is viable, without compromising Pt recovery (in the range 75–85%), as found for the mixture 2 M CaCl2 + 8 M HCl when compared to 11.6 M HCl. All leaching media showed good potential to recover Ce, particularly for higher reaction times and temperatures. Regarding SX, results achieved with a model solution were promising, but SX for Pt separation from the real SACC solution did not work as expected. For the adopted experimental conditions, the tested thiodiglycolamide derivative in toluene revealed a very good loading performance for both Pt and Fe, but Fe removal and Pt stripping from the organic phases after contact with the SACC solution were not successfully accomplished. Hence, the reutilization of the organic solvent needs improvement.

scholarly journals Mass and Heat Transfer Coefficients in Automotive Exhaust Catalytic Converter Channels

Catalysts ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 507
Author(s):  
Chrysovalantis C. Templis ◽  
Nikos G. Papayannakos
Keyword(s):  
Heat Transfer ◽  
Flow Reactor ◽  
Catalytic Converter ◽  
Reaction Rates ◽  
Cfd Model ◽  
Automotive Exhaust ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
Wide Range ◽  
Mass And Heat Transfer

Mass and heat transfer coefficients (MTC and HTC) in automotive exhaust catalytic monolith channels are estimated and correlated for a wide range of gas velocities and prevailing conditions of small up to real size converters. The coefficient estimation is based on a two dimensional computational fluid dynamic (2-D CFD) model developed in Comsol Multiphysics, taking into account catalytic rates of a real catalytic converter. The effect of channel size and reaction rates on mass and heat transfer coefficients and the applicability of the proposed correlations at different conditions are discussed. The correlations proposed predict very satisfactorily the mass and heat transfer coefficients calculated from the 2-D CFD model along the channel length. The use of a one dimensional (1-D) simplified model that couples a plug flow reactor (PFR) with mass transport and heat transport effects using the mass and heat transfer correlations of this study is proved to be appropriate for the simulation of the monolith channel operation.

scholarly journals Ni-γ-AL2O3 catalysts for obtaining nanocarbon by decomposition of natural gas

2021 ◽  
Author(s):  
Hikmet Ibrahimov ◽  
Sara Malikli ◽  
Zenfira Ibrahimova ◽  
Rahim Babali ◽  
Sevinc Aleskerova
Keyword(s):  
Natural Gas ◽  
Specific Surface ◽  
Catalytic Converter ◽  
Sol Gel ◽  
Nickel Content ◽  
Maximum Yield ◽  
Methane Decomposition ◽  
Impregnation Method ◽  
Decomposition Of Methane ◽  
Gas Supply

Abstractγ-Al2O3 was synthesized by the Sol–gel method, Ni (NO3)2 was placed in the pores by the impregnation method, and Ni-γ-Al2O3 was obtained by pyrolysis in a hydrogen stream in a CVD device. By the method of chemical vapors phase deposition (CVD) on Ni-Al2O3 catalytic converter with decomposition of methane in the natural gas produced carbon nanotubes (CNT) (Chunduri et al. in Mater Express 4(3):235–241, 2014; Zhou et al. in Appl Catal B 208:44–59, 2017). The catalytic activity of the catalysts in methane decomposition was examined from 650 °C to 900 °C by the method of chemical vapors phase deposition (CVD), the yield of CNTs tends to increase with the growth at the ratio of natural gas supply to hydrogen. The specific surface increases with an increase of nickel content and can reach 265.5 m2/g for a sample of 2% Ni-A12O3 at 850 °C. Growth at the temperature of methane decomposition leads to reduction in its specific surface. It has been established that the use of the Ni-Cu/γ-Al2O3 catalytic system, in which copper acts as a stabilizing additive, makes it possible to double the maximum yield of the carbon product during the decomposition of natural gas.

Sign in / Sign up

Export Citation Format

Share Document