Same-Side Platinum Electrodes for Metal Assisted Etching of Porous Silicon

2015 ◽  
Author(s):  
Matthew H. Ervin ◽  
Brian Isaacson
Keyword(s):  
Porous Silicon ◽  
Platinum Electrodes

Control of Metal Alloy Oxidation with Electric Fields

1973 ◽  
Vol 31 ◽  
pp. 164-165
Author(s):  
R. R. Dils ◽  
P. S. Follansbee
Keyword(s):  
Electric Fields ◽  
Oxidation Process ◽  
Base Alloy ◽  
Oxide Surface ◽  
Platinum Electrodes ◽  
Insulating Layer ◽  
Iron Base Alloy ◽  
Alloy Oxidation ◽  
Aluminum Oxide Layer ◽  
And Control

Electric fields have been applied across oxides growing on a high temperature alloy and control of the oxidation of the material has been demonstrated. At present, three-fold increases in the oxidation rate have been measured in accelerating fields and the oxidation process has been completely stopped in a retarding field.The experiments have been conducted with an iron-base alloy, Pe 25Cr 5A1 0.1Y, although, in principle, any alloy capable of forming an adherent aluminum oxide layer during oxidation can be used. A specimen is polished and oxidized to produce a thin, uniform insulating layer on one surface. Three platinum electrodes are sputtered on the oxide surface and the specimen is reoxidized.

Cerebral Tissue Response in Chronic Electrode Implantation

1977 ◽  
Vol 35 ◽  
pp. 624-625
Author(s):  
R.F. Dodson ◽  
L.W-F Chu ◽  
N. Ishihara
Keyword(s):  
Tissue Response ◽  
Whole Body ◽  
Platinum Electrodes ◽  
Fixed Tissue ◽  
Electrode Implantation ◽  
Surface Areas ◽  
Tissue Changes ◽  
Micron Diameter ◽  
Extent Of Damage ◽  
Electrode Sheath

The extent of damage surrounding an implanted electrode in the cerebral cortex is a question of significant importance with regard to attaining consistency and validity of physiological recordings. In order to determine the extent of such tissue changes, 150 micron diameter platinum electrodes were implanted in the cortex of four adult baboons, and after eight days the animals were sacrificed by whole body perfusion with a 3% glutaraldehyde in 0.1M phosphate fixative.The calvarium was carefully removed and the electrode tracts were readily discernible in the firm, glutaraldehyde fixed tissue.Careful dissection of the zone of the electrode tract resulted in a small block which was further sectioned into tip, mid-tract and surface areas. Ultrastructurally, damage extended from the electrode sheath to the greatest extent of from 0.2 to 3.5 mm.

Use of fractals to describe microstructures of porous thick-film platinum electrodes

1992 ◽  
Vol 50 (1) ◽  
pp. 314-315
Author(s):  
Steven D. Toteda
Keyword(s):  
Fractal Dimension ◽  
Power Plants ◽  
Electrical Response ◽  
Cubic Phase ◽  
Platinum Electrodes ◽  
Fine Grained ◽  
Impedance Response ◽  
Platinum Particles ◽  
Energy Surfaces ◽  
Highly Porous

Zirconia oxygen sensors, in such applications as power plants and automobiles, generally utilize platinum electrodes for the catalytic reaction of dissociating O2 at the surface. The microstructure of the platinum electrode defines the resulting electrical response. The electrode must be porous enough to allow the oxygen to reach the zirconia surface while still remaining electrically continuous. At low sintering temperatures, the platinum is highly porous and fine grained. The platinum particles sinter together as the firing temperatures are increased. As the sintering temperatures are raised even further, the surface of the platinum begins to facet with lower energy surfaces. These microstructural changes can be seen in Figures 1 and 2, but the goal of the work is to characterize the microstructure by its fractal dimension and then relate the fractal dimension to the electrical response. The sensors were fabricated from zirconia powder stabilized in the cubic phase with 8 mol% percent yttria. Each substrate was sintered for 14 hours at 1200°C. The resulting zirconia pellets, 13mm in diameter and 2mm in thickness, were roughly 97 to 98 percent of theoretical density. The Engelhard #6082 platinum paste was applied to the zirconia disks after they were mechanically polished ( diamond). The electrodes were then sintered at temperatures ranging from 600°C to 1000°C. Each sensor was tested to determine the impedance response from 1Hz to 5,000Hz. These frequencies correspond to the electrode at the test temperature of 600°C.

Calculation of exchange energy in quantum dots : application to porous silicon

1993 ◽  
Vol 03 (C5) ◽  
pp. 355-358 ◽  
Author(s):  
G. FISHMAN ◽  
R. ROMESTAIN ◽  
J. C. VIAL
Keyword(s):  
Quantum Dots ◽  
Porous Silicon ◽  
Exchange Energy

SrBi2Nb2O9 ferroelectric thin films deposited by pulsed laser deposition on textured and epitaxied platinum electrodes

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-133-Pr11-137
Author(s):  
J. R. Duclère ◽  
M. Guilloux-Viry ◽  
A. Perrin ◽  
A. Dauscher ◽  
S. Weber ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Platinum Electrodes

ANTI-REFLECTIVE PROPERTIES OF GRADIENT-POROUS SILICON

2017 ◽  
pp. 16-25
Author(s):  
E. A. Gosteva ◽  
V. V. Starkov ◽  
Yu. N. Parhomenko ◽  
M. O. Kah ◽  
I. A. Iwe
Keyword(s):  
Porous Silicon

Investigation of Porous Silicon/Carbon Composite as Anodes for Lithium Ion Batteries

2015 ◽  
Vol 30 (4) ◽  
pp. 351 ◽  
Author(s):  
HUANG Yan-Hua ◽  
HAN Xiang ◽  
CHEN Hui-Xin ◽  
CHEN Song-Yan ◽  
YANG Yong
Keyword(s):  
Porous Silicon ◽  
Lithium Ion Batteries ◽  
Lithium Ion ◽  
Carbon Composite ◽  
Silicon Carbon
Sign in / Sign up

Export Citation Format

Share Document