Gas Analysis and Control Methods for Thermal Batteries

2013 ◽  
Author(s):  
Frank C. Krieger ◽  
Michael S. Ding
Keyword(s):  
Gas Analysis ◽  
Control Methods ◽  
Thermal Batteries ◽  
And Control

Cooperative ship formation system and control methods in the ship lock waterway

2021 ◽  
Vol 226 ◽  
pp. 108826
Author(s):  
Chenguang Liu ◽  
Junlin Qi ◽  
Xiumin Chu ◽  
Mao Zheng ◽  
Wei He
Keyword(s):  
Control Methods ◽  
And Control ◽  
Formation System ◽  
Ship Lock

scholarly journals Research on influence factors and control methods of backfill compactness

2021 ◽  
Vol 787 (1) ◽  
pp. 012027
Author(s):  
Yudian Li ◽  
Jiajie Dong ◽  
Kai Fei ◽  
Hao Song ◽  
Zeyi Li ◽  
...  
Keyword(s):  
Influence Factors ◽  
Control Methods ◽  
And Control

scholarly journals Characterisation and Control of a Woven Biomimetic Actuator for Wearable Neurorehabilitative Devices

Actuators ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 37
Author(s):  
Vaughan Murphy ◽  
Brandon P. R. Edmonds ◽  
Ana Luisa Trejos
Keyword(s):  
Performance Metrics ◽  
Woven Fabric ◽  
Total Force ◽  
Control Methods ◽  
Soft Actuator ◽  
Sewing Thread ◽  
And Control ◽  
Fabric Mesh ◽  
Biomimetic Actuator ◽  
Multiple Units

Twisted coiled actuators (TCAs) are a type of soft actuator made from polymer fibres such as nylon sewing thread. As they provide motion in a compact, lightweight, and flexible package, they provide a solution to the actuation of wearable mechatronic devices for motion assistance. Their limitation is that they provide low total force, requiring them to actuate in parallel with multiple units. Previous literature has shown that the force and stroke production can be improved by incorporating them into fabric meshes. A fabric mesh could also improve the contraction efficiency, strain rate, and user comfort. Therefore, this study focused on measuring these performance metrics for a set of TCAs embedded into a woven fabric mesh. The experimental results show that the stroke of the actuators scaled linearly with the number of activated TCAs, achieving a maximum applied force of 11.28 N, a maximum stroke of 12.23%, and an efficiency of 1.8%. Additionally, two control methods were developed and evaluated, resulting in low overshoot and steady-state error. These results indicate that the designed actuators are viable for use in wearable mechatronic devices, since they can scale to meet different requirements, while being able to be accurately controlled with minimal additional components.

scholarly journals Resonance Instability of Photovoltaic E-Bike Charging Stations: Control Parameters Analysis, Modeling and Experiment

2019 ◽  
Vol 9 (2) ◽  
pp. 252 ◽  
Author(s):  
Ziqian Zhang ◽  
Cihan Gercek ◽  
Herwig Renner ◽  
Angèle Reinders ◽  
Lothar Fickert
Keyword(s):  
Major Effect ◽  
Current Control ◽  
Current Loop ◽  
Control Methods ◽  
Control Parameters ◽  
Charging System ◽  
Grid Connected Inverter ◽  
The Time Domain ◽  
Charging Stations ◽  
And Control

This article presents an in-situ comparative analysis and power quality tests of a newly developed photovoltaic charging system for e-bikes. The various control methods of the inverter are modeled and a single-phase grid-connected inverter is tested under different conditions. Models are constituted for two current control methods; the proportional resonance and the synchronous rotating frames. In order to determine the influence of the control parameters, the system is analyzed analytically in the time domain as well as in the frequency domain by simulation. The tests indicated the resonance instability of the photovoltaic inverter. The passivity impedance-based stability criterion is applied in order to analyze the phenomenon of resonance instability. In conclusion, the phase-locked loop (PLL) bandwidth and control parameters of the current loop have a major effect on the output admittance of the inverter, which should be adjusted to make the system stable.

Numerical Simulation of Blasting-Induced Damage in Grouting Curtain of Sandstone Aquifer for Vertical Shaft

2015 ◽  
Vol 723 ◽  
pp. 271-278
Author(s):  
Yu Liang Zhou ◽  
Dong Feng Yuan ◽  
Jun Zheng ◽  
Hua Wang
Keyword(s):  
Numerical Simulation ◽  
Prevention And Control ◽  
Damage Zone ◽  
Surrounding Rock ◽  
Damage Effect ◽  
Vertical Shaft ◽  
Control Methods ◽  
Sandstone Aquifer ◽  
And Control ◽  
Dynamic Damage

To provide a theoretical basis for water prevention and control methods and reasonable supporting techniques for vertical shaft, and to ensure the shaft construction to pass the sandstone aquifer safely and rapidly, numerical simulation using dynamic damage constitutive model, which was a user-defined constitutive modules in FLAC3D, a lagrangian analysis code in three dimensions, has been applied to investigate the dynamic damage effect in the surrounding rock of the grouting curtain near the driving working face for vertical shaft excavated by blasting. The results indicate that the distribution of the damage zone in the surrounding rock of the shaft, which decreases the effective thickness of the grouting curtain, was like a ellip-se, and that the depth of the damage zone in the surrounding rock of the shaft grouting curtain is fewer than that of the driving face floor. It can be concluded that the centre part of the driving face floor, especially the cutting hole zones, and the shaft wall in the greater horizontal stress side are the " key parts " for shaft water prevention and control methods.

Sign in / Sign up

Export Citation Format

Share Document