Stagnation Point Flow and Heat Transfer Under Free-Stream Turbulence

2004 ◽  
Author(s):  
Zhongmin Xiong ◽  
Sanjiva K. Lele
Keyword(s):  
Heat Transfer ◽  
Stagnation Point ◽  
Free Stream ◽  
Stagnation Point Flow ◽  
Free Stream Turbulence ◽  
Flow And Heat Transfer

Stagnation-point flow under free-stream turbulence

2007 ◽  
Vol 590 ◽  
pp. 1-33 ◽  
Author(s):  
ZHONGMIN XIONG ◽  
SANJIVA K. LELE
Keyword(s):  
Heat Transfer ◽  
Stagnation Point ◽  
Reynolds Stress ◽  
Free Stream ◽  
Leading Edge ◽  
Stagnation Point Flow ◽  
Mean Flow ◽  
Free Stream Turbulence ◽  
Local Boundary ◽  
The Mean

In this paper, the effects of free-stream turbulence on stagnation-point flow and heat transfer are investigated through large eddy simulation (LES) of homogeneous isotropic turbulence impinging upon an isothermal elliptical leading edge. Turbulent mean flow and Reynolds stress profiles along the stagnation streamline, where the mean flow is strain dominant, and at different downstream locations, where the mean flow gradually becomes shear-dominated, are used to characterize evolution of the free-stream turbulence. The Reynolds stress budgets are also obtained, and the turbulence anisotropy is analysed through the balance between the mean flow strain and the velocity pressure gradient correlation. In the presence of free-stream turbulence, intense quasi-streamwise vortices develop near the leading edge with a typical diameter of the order of the local boundary-layer thickness. These strong vortices cause the thermal fluxes to peak at a location much closer to the wall than that of the Reynolds stresses, resulting a greater sensitivity to free-stream turbulence for the heat transfer than the momentum transfer. The heat transfer enhancement obtained by the present LES agrees quantitatively with available experimental measurements. The present LES results are also used to examine the eddy viscosity and pressure-strain correlations in Reynolds stress turbulence models.

Numerical solutions of non-alignment stagnation-point flow and heat transfer over a stretching/shrinking surface in a nanofluid

2016 ◽  
Vol 26 (6) ◽  
pp. 1747-1767 ◽  
Author(s):  
Ioan Pop ◽  
Kohi Naganthran ◽  
Roslinda Nazar
Keyword(s):  
Heat Transfer ◽  
Differential Equations ◽  
Stagnation Point ◽  
Numerical Solutions ◽  
Dual Solutions ◽  
Stagnation Point Flow ◽  
Content Type ◽  
Boundary Layer Equations ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

Purpose – The purpose of this paper is to analyse numerically the steady stagnation-point flow of a viscous and incompressible fluid over continuously non-aligned stretching or shrinking surface in its own plane in a water-based nanofluid which contains three different types of nanoparticles, namely, Cu, Al2O3 and TiO2. Design/methodology/approach – Similarity transformation is used to convert the system of boundary layer equations which are in the form of partial differential equations into a system of ordinary differential equations. The system of similarity governing equations is then reduced to a system of first-order differential equations and solved numerically using the bvp4c function in Matlab software. Findings – Unique solution exists when the surface is stretched and dual solutions exist as the surface shrunk. For the dual solutions, stability analysis has revealed that the first solution (upper branch) is stable and physically realizable, while the second solution (lower branch) is unstable. The effect of non-alignment is huge for the shrinking surface which is in contrast with the stretching surface. Practical implications – The results obtained can be used to explain the characteristics and applications of nanofluids, which are widely used as coolants, lubricants, heat exchangers and micro-channel heat sinks. This problem also applies to some situations such as materials which are manufactured by extrusion, production of glass-fibre and shrinking balloon. In this kind of circumstance, the rate of cooling and the stretching/shrinking process play an important role in moulding the final product according to preferable features. Originality/value – The present results are original and new for the study of fluid flow and heat transfer over a stretching/shrinking surface for the problem considered by Wang (2008) in a viscous fluid and extends to nanofluid by using the Tiwari and Das (2007) model.

Stagnation-Point Flow over an Exponentially Shrinking/Stretching Sheet

2011 ◽  
Vol 66 (12) ◽  
pp. 705-711 ◽  
Author(s):  
Sin Wei Wong ◽  
Abu Omar Awang ◽  
Anuar Ishak
Keyword(s):  
Differential Equations ◽  
Stagnation Point ◽  
Stretching Sheet ◽  
Free Stream ◽  
Stagnation Point Flow ◽  
Stream Velocity ◽  
Heat Transfer Characteristics ◽  
Keller Box Method ◽  
Flow And Heat Transfer ◽  
Box Method

The steady two-dimensional stagnation-point flow of an incompressible viscous fluid over an exponentially shrinking/stretching sheet is studied. The shrinking/stretching velocity, the free stream velocity, and the surface temperature are assumed to vary in a power-law form with the distance from the stagnation point. The governing partial differential equations are transformed into a system of ordinary differential equations before being solved numerically by a finite difference scheme known as the Keller-box method. The features of the flow and heat transfer characteristics for different values of the governing parameters are analyzed and discussed. It is found that dual solutions exist for the shrinking case, while for the stretching case, the solution is unique.

Stability analysis on the stagnation-point flow and heat transfer over a permeable stretching/shrinking sheet with heat source effect

2018 ◽  
Vol 28 (11) ◽  
pp. 2650-2663 ◽  
Author(s):  
Fatinnabila Kamal ◽  
Khairy Zaimi ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Stability Analysis ◽  
Heat Source ◽  
Skin Friction ◽  
Stagnation Point ◽  
Stagnation Point Flow ◽  
Shrinking Sheet ◽  
Content Type ◽  
Source Effect ◽  
Flow And Heat Transfer

PurposeThis paper aims to analyze the behavior of the stagnation-point flow and heat transfer over a permeable stretching/shrinking sheet in the presence of the viscous dissipation and heat source effects.Design/methodology/approachThe governing partial differential equations are converted into ordinary differential equations by similarity transformations before being solved numerically using the bvp4c function built in Matlab software. Effects of suction/injection parameter and heat source parameter on the skin friction and heat transfer coefficients as well as the velocity and temperature profiles are presented in the forms of tables and graphs. A temporal stability analysis will be conducted to verify which solution is stable for the dual solutions exist for the shrinking case.FindingsThe analysis indicates that the skin friction coefficient and the local Nusselt number as well as the velocity and temperature were influenced by suction/injection parameter. In contrast, only the local Nusselt number, which represents heat transfer rate at the surface, was affected by heat source effect. Further, numerical results showed that dual solutions were found to exist for the certain range of shrinking case. Then, the stability analysis is performed, and it is confirmed that the first solution is linearly stable and has real physical implication, while the second solution is not.Practical implicationsIn practice, the study of the steady two-dimensional stagnation-point flow and heat transfer past a permeable stretching/shrinking sheet in the presence of heat source effect is very crucial and useful. The problems involving fluid flow over stretching or shrinking surfaces can be found in many industrial manufacturing processes such as hot rolling, paper production and spinning of fibers. Owing to the numerous applications, the study of stretching/shrinking sheet was subsequently extended by many authors to explore various aspects of skin friction coefficient and heat transfer in a fluid. Besides that, the study of suction/injection on the boundary layer flow also has important applications in the field of aerodynamics and space science.Originality/valueAlthough many studies on viscous fluid has been investigated, there is still limited discoveries found on the heat source and suction/injection effects. Indeed, this paper managed to obtain the second (dual) solutions and stability analysis is performed. The authors believe that all the results are original and have not been published elsewhere.

Unsteady separated stagnation-point flow and heat transfer past a stretching/shrinking sheet in a copper-water nanofluid

2019 ◽  
Vol 29 (8) ◽  
pp. 2588-2605 ◽  
Author(s):  
Natalia C. Roşca ◽  
Alin V. Roşca ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Partial Differential Equations ◽  
Differential Equations ◽  
Stagnation Point ◽  
Design Methodology ◽  
Similarity Transformation ◽  
Stagnation Point Flow ◽  
Shrinking Sheet ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to theoretically investigate the unsteady separated stagnation-point flow and heat transfer past an impermeable stretching/shrinking sheet in a copper (Cu)-water nanofluid using the mathematical nanofluid model proposed by Tiwari and Das. Design/methodology/approach A similarity transformation is used to reduce the governing partial differential equations to a set of nonlinear ordinary (similarity) differential equations which are then solved numerically using the function bvp4c from Matlab for different values of the governing parameters. Findings It is found that the solution is unique for stretching case; however, multiple (dual) solutions exist for the shrinking case. Originality/value The authors believe that all numerical results are new and original, and have not been published elsewhere.

Sign in / Sign up

Export Citation Format

Share Document