Constitutive Behavior and Damage Characterization of High Temperature Polymer Composites

2001 ◽  
Author(s):  
Isaac M. Daniel ◽  
Jyi-Jiin Luo ◽  
Zuo Sun
Keyword(s):  
High Temperature ◽  
Polymer Composites ◽  
Constitutive Behavior ◽  
Damage Characterization

Characterization of the Thermo-Oxidative Stability of Filled Thermoplastic Polyetherimide

Materials ◽  
2003 ◽  
Author(s):  
V. A. Harinath ◽  
Jianzhong Lou ◽  
Jag Sankar ◽  
Leonard Uitenham
Keyword(s):  
High Temperature ◽  
Thermogravimetric Analysis ◽  
Oxidative Stability ◽  
Polymer Composites ◽  
Polymer Composite ◽  
Polymeric Composites ◽  
Filler Loading ◽  
Service Temperature ◽  
Temperature Conditions

Selected fillers were incorporated to prepare polytherimide composite. The influence of fillers on the thermo-oxidative stability of the composite was studied by thermogravimetric analysis. The results showed that at optical filler loading and characteristics, the polymer composite became superior in its thermo-oxidative stability that is very promising in widening the window of service temperature of polyimides for extremely high temperature conditions where most polymeric composites fail. The findings should prove useful in developing high-temperature polymer composites for aerospace and electronics applications.

Thermo-mechanical characterization of nonwoven fabric reinforced polymer composites

2020 ◽  
Author(s):  
Sachin Tejyan ◽  
Divyesh Sharma ◽  
Brijesh Gangil ◽  
Amar Patnaik ◽  
Tej Singh
Keyword(s):  
Polymer Composites ◽  
Mechanical Characterization ◽  
Nonwoven Fabric ◽  
Reinforced Polymer

scholarly journals Fabrication and Characterization of Quinary High Entropy-Ultra-High Temperature Diborides

Ceramics ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 108-120
Author(s):  
Simone Barbarossa ◽  
Roberto Orrù ◽  
Valeria Cannillo ◽  
Antonio Iacomini ◽  
Sebastiano Garroni ◽  
...  
Keyword(s):  
High Temperature ◽  
Single Phase ◽  
Nominal Composition ◽  
High Entropy ◽  
Chemical Complexity ◽  
Alternative Processing ◽  
Plasma Sintering ◽  
High Temperature Synthesis ◽  
Spark Plasma

Due to their inherent chemical complexity and their refractory nature, the obtainment of highly dense and single-phase high entropy (HE) diborides represents a very hard target to achieve. In this framework, homogeneous (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2, (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2, and (Hf0.2Zr0.2Nb0.2Mo0.2Ti0.2)B2 ceramics with high relative densities (97.4, 96.5, and 98.2%, respectively) were successfully produced by spark plasma sintering (SPS) using powders prepared by self-propagating high-temperature synthesis (SHS). Although the latter technique did not lead to the complete conversion of initial precursors into the prescribed HE phases, such a goal was fully reached after SPS (1950 °C/20 min/20 MPa). The three HE products showed similar and, in some cases, even better mechanical properties compared to ceramics with the same nominal composition attained using alternative processing methods. Superior Vickers hardness and elastic modulus values were found for the (Hf0.2Nb0.2Ta0.2Mo0.2Ti0.2)B2 and the (Hf0.2Zr0.2Ta0.2Mo0.2Ti0.2)B2 systems, i.e., 28.1 GPa/538.5 GPa and 28.08 GPa/498.1 GPa, respectively, in spite of the correspondingly higher residual porosities (1.2 and 2.2 vol.%, respectively). In contrast, the third ceramic, not containing tantalum, displayed lower values of these two properties (25.1 GPa/404.5 GPa). However, the corresponding fracture toughness (8.84 MPa m1/2) was relatively higher. This fact can be likely ascribed to the smaller residual porosity (0.3 vol.%) of the sintered material.

scholarly journals Multianvil High-Pressure/High-Temperature Synthesis and Characterization of multiferroic HP-Co3TeO6

2021 ◽  
Author(s):  
Gunter Heymann ◽  
Elisabeth Selb ◽  
Toni Buttlar ◽  
Oliver Janka ◽  
Martina Tribus ◽  
...  
Keyword(s):  
High Pressure ◽  
High Temperature ◽  
Type Structure ◽  
Synthesis And Characterization ◽  
Temperature Synthesis ◽  
Space Group ◽  
Crystal System ◽  
High Temperature Synthesis ◽  
High Pressure High Temperature

By high-pressure/high-temperature multianvil synthesis a new high-pressure (HP) phase of Co3TeO6 was obtained. The compound crystallizes in the acentric trigonal crystal system of the Ni3TeO6-type structure with space group R3...

Sign in / Sign up

Export Citation Format

Share Document