Plastic Deformation of Granular Materials

The use of resilient models to describe the behavior of the materials in pavement design is the current standard. However, there are periods of the year when these resilient models may not be valid. Granular materials in pavements show some resiliency at every load level and moisture content. Nonresiliency is critical, however, when the plastic deformation becomes a large portion of the overall deformation in response to a load. Detection of possible nonresiliency in a pavement during use of a falling-weight deflectometer (FWD) would alert the FWD operator to possible nonresilient behavior. Two statistical checks are proposed to test for nonresiliency using the raw data provided by the FWD. Daily testing of a very weak pavement during spring thaw provided FWD data during and after a period of known nonresilient behavior. A chi-squared test of the variance may be able to detect nonresilient behavior.

Download Full-text

Sem Examinations of Glass Knives

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100068400 ◽

1970 ◽

Vol 28 ◽

pp. 282-283

Author(s):

J. Temple Black

Keyword(s):

Plastic Deformation ◽

Tensile Loading ◽

Resultant Force ◽

Stress Concentrations ◽

Edge Chipping ◽

Surface Flaws ◽

Edge Defects ◽

Microscopic Surface

There are two types of edge defects common to glass knives as typically prepared for microtomy purposes: 1) striations and 2) edge chipping. The former is a function of the free breaking process while edge chipping results from usage or bumping of the edge. Because glass has no well defined planes in its structure, it should be highly resistant to plastic deformation of any sort, including tensile loading. In practice, prevention of microscopic surface flaws is impossible. The surface flaws produce stress concentrations so that tensile strengths in glass are typically 10-20 kpsi and vary only slightly with composition. If glass can be kept in compression, wherein failure is literally unknown (1), it will remain intact for long periods of time. Forces acting on the tool in microtomy produce a resultant force that acts to keep the edge in compression.

Download Full-text

Stereo Electron Microscopy Applied to High Resolution Freeze-Etch Replicas

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100068527 ◽

1970 ◽

Vol 28 ◽

pp. 306-307

Author(s):

L. Andrew Staehelin

Keyword(s):

Electron Microscopy ◽

Plastic Deformation ◽

High Resolution ◽

Smooth Surfaces ◽

Small Particles ◽

Membrane Surfaces ◽

Wide Acceptance ◽

New Information ◽

Number Of Particles ◽

Small Holes

Freeze-etched membranes usually appear as relatively smooth surfaces covered with numerous small particles and a few small holes (Fig. 1). In 1966 Branton (1“) suggested that these surfaces represent split inner mem¬brane faces and not true external membrane surfaces. His theory has now gained wide acceptance partly due to new information obtained from double replicas of freeze-cleaved specimens (2,3) and from freeze-etch experi¬ments with surface labeled membranes (4). While theses studies have fur¬ther substantiated the basic idea of membrane splitting and have shown clearly which membrane faces are complementary to each other, they have left the question open, why the replicated membrane faces usually exhibit con¬siderably fewer holes than particles. According to Branton's theory the number of holes should on the average equal the number of particles. The absence of these holes can be explained in either of two ways: a) it is possible that no holes are formed during the cleaving process e.g. due to plastic deformation (5); b) holes may arise during the cleaving process but remain undetected because of inadequate replication and microscope techniques.

Download Full-text

Plastic Deformation in Microtomed Sections

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100066346 ◽

1971 ◽

Vol 29 ◽

pp. 458-459

Author(s):

J. Temple Black

Keyword(s):

Plastic Deformation ◽

Plastic Strain ◽

Applied Stress ◽

Elastic Strain ◽

High Strain ◽

Tool Material ◽

Cutting Edge ◽

Material Structure ◽

Geometrical Constraints

The output of the ultramicrotomy process with its high strain levels is dependent upon the input, ie., the nature of the material being machined. Apart from the geometrical constraints offered by the rake and clearance faces of the tool, each material is free to deform in whatever manner necessary to satisfy its material structure and interatomic constraints. Noncrystalline materials appear to survive the process undamaged when observed in the TEM. As has been demonstrated however microtomed plastics do in fact suffer damage to the top and bottom surfaces of the section regardless of the sharpness of the cutting edge or the tool material. The energy required to seperate the section from the block is not easily propogated through the section because the material is amorphous in nature and has no preferred crystalline planes upon which defects can move large distances to relieve the applied stress. Thus, the cutting stresses are supported elastically in the internal or bulk and plastically in the surfaces. The elastic strain can be recovered while the plastic strain is not reversible and will remain in the section after cutting is complete.

Download Full-text