Kinetics of Straininduced Crystallization of Polymers During Flow.

ABSTRACTThe effect of pre-crystallization pulsed magnetic field (PMF) treatment of linear flexible-chain polymers on kinetics of their crystallization and structure in the crystalline state has been studied in polydimethylsiloxane (PDMS) and polyethylene oxide (PEO). It was established that the PMF treatment can destruct the initial net of non-chemically bonded “physical nodes” of the polymer and thus turn the melt into a metastable state with the increased sensitivity to regimes of crystallization. The effect revealed can lay the foundation for the development of new effective methods of controlled crystallization of the flexible-chain polymers, including fractionation and crystallization of polymorphic polymers in the chosen structural modification.

Download Full-text

Some fundamental aspects of the kinetics of flow-induced crystallization of polymers

Colloid & Polymer Science ◽

10.1007/s00396-010-2266-y ◽

2010 ◽

Vol 288 (16-17) ◽

pp. 1525-1537 ◽

Cited By ~ 27

Author(s):

H. Janeschitz-Kriegl ◽

Ewa Ratajski

Keyword(s):

Crystallization Of Polymers ◽

Kinetics Of ◽

Induced Crystallization ◽

Flow Induced Crystallization

Download Full-text

Direct observations of radiation-enhanced transformations in glass

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100075543 ◽

1983 ◽

Vol 41 ◽

pp. 354-355

Author(s):

J. F. DeNatale ◽

D. G. Howitt

Keyword(s):

Glass Matrix ◽

Diffusion Mechanism ◽

Bubble Formation ◽

Silicate Glasses ◽

Phase Decomposition ◽

Direct Observations ◽

Thin Foils ◽

Oxygen Bubble ◽

Electron Energy Loss ◽

Kinetics Of

The electron irradiation of silicate glasses containing metal cations produces various types of phase separation and decomposition which includes oxygen bubble formation at intermediate temperatures figure I. The kinetics of bubble formation are too rapid to be accounted for by oxygen diffusion but the behavior is consistent with a cation diffusion mechanism if the amount of oxygen in the bubble is not significantly different from that in the same volume of silicate glass. The formation of oxygen bubbles is often accompanied by precipitation of crystalline phases and/or amorphous phase decomposition in the regions between the bubbles and the detection of differences in oxygen concentration between the bubble and matrix by electron energy loss spectroscopy cannot be discerned (figure 2) even when the bubble occupies the majority of the foil depth.The oxygen bubbles are stable, even in the thin foils, months after irradiation and if van der Waals behavior of the interior gas is assumed an oxygen pressure of about 4000 atmospheres must be sustained for a 100 bubble if the surface tension with the glass matrix is to balance against it at intermediate temperatures.

Download Full-text

Irradiation behavior of pyrolytic silicon carbide

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100074288 ◽

1983 ◽

Vol 41 ◽

pp. 72-73

Author(s):

R. J. Lauf

Keyword(s):

Silicon Carbide ◽

Fission Products ◽

Thermodynamics And Kinetics ◽

Neutron Fluences ◽

Fuel Particles ◽

Sic Coatings ◽

Irradiation Behavior ◽

Kinetics Of ◽

Htgr Fuel

Fuel particles for the High-Temperature Gas-Cooled Reactor (HTGR) contain a layer of pyrolytic silicon carbide to act as a miniature pressure vessel and primary fission product barrier. Optimization of the SiC with respect to fuel performance involves four areas of study: (a) characterization of as-deposited SiC coatings; (b) thermodynamics and kinetics of chemical reactions between SiC and fission products; (c) irradiation behavior of SiC in the absence of fission products; and (d) combined effects of irradiation and fission products. This paper reports the behavior of SiC deposited on inert microspheres and irradiated to fast neutron fluences typical of HTGR fuel at end-of-life.

Download Full-text

The Ordered Phase Formation in Ti-Al-Ga Alloys

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100069193 ◽

1970 ◽

Vol 28 ◽

pp. 440-441

Author(s):

Shiro Fujishiro ◽

Harold L. Gegel

Keyword(s):

Thermal Stability ◽

High Temperature ◽

Titanium Alloys ◽

Growth Kinetics ◽

Stoichiometric Composition ◽

Good Potential ◽

Alpha Titanium ◽

Cold Rolled ◽

Kinetics Of ◽

Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

Download Full-text

Ion Beam Induced Interfacial Reactions in Molybdenum Thin Films on Silicon

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100097466 ◽

1981 ◽

Vol 39 ◽

pp. 162-163

Author(s):

L. J. Chen ◽

L. S. Hung ◽

J. W. Mayer

Keyword(s):

Ion Beam ◽

Chemical Vapor ◽

Interfacial Reactions ◽

Practical Applications ◽

Microelectronic Devices ◽

Recent Emergence ◽

Chemical Vapor Deposited ◽

Atomic Mixing ◽

Silicon Interface ◽

Kinetics Of

When an energetic ion penetrates through an interface between a thin film (of species A) and a substrate (of species B), ion induced atomic mixing may result in an intermixed region (which contains A and B) near the interface. Most ion beam mixing experiments have been directed toward metal-silicon systems, silicide phases are generally obtained, and they are the same as those formed by thermal treatment.Recent emergence of silicide compound as contact material in silicon microelectronic devices is mainly due to the superiority of the silicide-silicon interface in terms of uniformity and thermal stability. It is of great interest to understand the kinetics of the interfacial reactions to provide insights into the nature of ion beam-solid interactions as well as to explore its practical applications in device technology.About 500 Å thick molybdenum was chemical vapor deposited in hydrogen ambient on (001) n-type silicon wafer with substrate temperature maintained at 650-700°C. Samples were supplied by D. M. Brown of General Electric Research & Development Laboratory, Schenectady, NY.

Download Full-text