Deviation Angle / Turning Angle Prediction for Advanced Axial-Flow Compressor Blade Row Geometries.

1977 ◽  
Author(s):  
George K. Serovy
Keyword(s):  
Axial Flow ◽  
Compressor Blade ◽  
Deviation Angle ◽  
Turning Angle ◽  
Axial Flow Compressor ◽  
Blade Row ◽  
Flow Compressor

An Implicit Off-Design Deviation Angle Correlation of Axial Flow Compressor Blade Elements

2017 ◽  
Author(s):  
Wu Dong-run ◽  
Teng Jin-fang ◽  
Qiang Xiao-qing ◽  
Feng Jin-zhang
Keyword(s):  
Experimental Data ◽  
Incidence Angle ◽  
High Reliability ◽  
Axial Flow ◽  
Compressor Blade ◽  
Deviation Angle ◽  
Axial Flow Compressor ◽  
New Correlation ◽  
Classical Correlations ◽  
Flow Compressor

This paper applies a new analytical/empirical method to formulate the off-design deviation angle correlation of axial flow compressor blade elements. An implicit function of deviation angle is used to map off-design deviation curves into linear correlations (minimum linear correlation coefficient R = 0.959 in this paper). Solution of the coefficients in the correlation is given through the study of classical theories and statistical analysis of the experimental data. The off-design deviation angle can be calculated numerically. The approach requires only knowledge of the blade element geometry. The comparison among 2 classical correlations and the new correlation proposed in this paper shows the new correlation has minimum error over the entire range of incidence angle while classical correlations show high reliability only in a limited range. Experimental data in this paper is collected from NASA’s open technical reports. Rotors and stators are studied together. Considering there is significant deviation angle variation along spanwise direction, only data at 50% span is studied, if possible. The error among experimental data, statistical regressions of the experimental data, and numerical results based on the new correlation is discussed. It has to be noted that the influence of the flow condition other than incidence angle is only being discussed but with less break through.

Influence of Rain Ingestion on the Endwall Treatment in an Axial Flow Compressor

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
Jichao Li ◽  
Juan Du ◽  
Mingzhen Li ◽  
Feng Lin ◽  
Hongwu Zhang ◽  
...  
Keyword(s):  
Rotor Blade ◽  
Axial Flow ◽  
Pressure Rise ◽  
Water Film ◽  
Stall Margin ◽  
Axial Flow Compressor ◽  
Water Ingestion ◽  
Blade Row ◽  
Flow Compressor ◽  
The Stability

The effects of water ingestion on the performance of an axial flow compressor are experimentally studied with and without endwall treatment. The background to the work is derived from the assessment of airworthiness for an aero-engine. The stability-enhancing effects with endwall treatments under rain ingestion are not previously known. Moreover, all the endwall treatments are designed under dry air conditions in the compressor. Water ingestion at 3% and 5% relative to the design mass flow proposed in the airworthiness standard are applied to initially investigate the effects on the performance under smooth casing (SC). Results show that the water ingestions are mainly located near the casing wall after they move through the rotor blade row. The pressure rise coefficient increases, efficiency declines, and torque increases under the proposed water ingestion. The increase of the inlet water increases the thickness of the water film downstream the rotor blade row and aggravates the adverse effects on the performances. Subsequently, three endwall treatments, namely circumferential grooves, axial slots, and hybrid slots–grooves, are tested with and without water ingestion. Compared with no water ingestion, the circumferential grooves basically have no resistance to the water ingestion. The axial slots best prevent the drop of the pressure rise coefficient induced by water ingestion, and hybrid slots–grooves are the second-best place owing to the contribution of the front axial slots. Therefore, the hybrid slots–grooves can not only extend the stall margin with less efficiency penalty compared with axial slots, but also prevent rain ingestion from worsening the compressor performance.

Material Optimizations on UAV’s axial flow compressor blade by using FSI Approach

2022 ◽  
Author(s):  
Vijayanandh Raja ◽  
Meenakshi Samy ◽  
Keerthana Nachimuthu ◽  
Samrithi Sathyamoorthy ◽  
Deviparameswari Krishnasamy ◽  
...  
Keyword(s):  
Axial Flow ◽  
Compressor Blade ◽  
Axial Flow Compressor ◽  
Flow Compressor

Mean Velocity and Decay Characteristics of the Guidevane and Stator Blade Wake of an Axial Flow Compressor

1980 ◽  
Vol 102 (1) ◽  
pp. 50-60 ◽  
Author(s):  
B. Lakshminarayana ◽  
R. Davino
Keyword(s):  
Axial Flow ◽  
Mean Velocity ◽  
Axial Flow Compressor ◽  
Profile Similarity ◽  
Blade Row ◽  
Wake Production ◽  
Flow Curvature ◽  
Stator Blade ◽  
Single Sensor ◽  
Flow Compressor

Pure tone noise, blade row vibrations, and aerodynamic losses are phenomena which are influenced by stator and IGV blade wake production, decay, and interaction in an axial-flow compressor. The objective of this investigation is to develop a better understanding of the nature of stator and IGV blade wakes that are influenced by the presence of centrifugal forces due to flow curvature. A single sensor hot wire probe was employed to determine the three mean velocity components of stator and IGV wakes of a single stage compressor. These wake profiles indicated a varying decay rate of the tangential and axial wake velocity components and a wake profile similarity. An analysis, which predicts this trend, has been developed. The radial velocities are found to be appreciable in both IGV and the stator wakes. This wake data as well as the data from other sources are correlated in this paper. Appreciable static pressure gradient across the wake is found to exist near the trailing edge of both stator and IGV.

Sign in / Sign up

Export Citation Format

Share Document